Remote Internet Monitoring Quick Start Guide For IP Camera Models: QSTC201 QSTC211
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 The Q-See IP Camera Model QST201/211 with our New Firmware v 1.3.0 Build 20091022 allows you to: 1. 2. 3. 4. Record Live Footage Directly to your PC via Internet Explorer Playback Recorded Video Files via Internet Explorer Receive Email Notifications when Motion is Detected Enable Dynamic Network Service through www.dyndns.com and my-qsee.com.
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 (Figure 2) *Note that the example of this IPTOOL screen above lists an IP Camera with the Device Name of “name”, an IP Address of 192.168.1.201, a Subnet Mask of 255.255.255.0 and a Gateway of 192.168.1.1 d.
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 (Figure 5) (Figure 6) 2. Setting up the Wireless Function of the Camera a. Go to: [START→ALL PROGRAMS→CONTROL CENTER→IPTOOL] on your Windows Start Bar. This will generate a dialog box listing all connected IP Cameras (see Figure 2). From here, right click on the camera you wish to set the wireless function for.
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 d. The name of your router will appear in your list of routers under the column “SSID”. Clicking on the router will reveal the IP, Gateway, DNS and Subnet Mask Addresses on lower right hand side of your Wireless Setting dialog box. e. Please note that if your Router is encrypted, then you will need to set all the addresses manually with the addresses listed on your IPTOOL screen (See Figure 4).
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 3. Setting up Email Notification. This function allows you to receive email messages if your system detects some type of motion. To receive email notification when your camera detects motion, you must first enter the information for your email addresses using your IPTOOL program. To do this, follow these steps: a. Go to: [START→ALL PROGRAMS→CONTROL CENTER→IPTOOL] on your Windows Start Bar.
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 (Figure 9) b. After you click the Setup button, a menu will appear on the left hand side of your screen (Figure 9). Click on the [Mail Config] option from the menu (circled in red, Figure 9). This will generate a configuration dialog on the right hand side of your screen (Figure 10) where you can set your email accounts up and set your notification preferences by following these steps: 1.
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 2. Enter the email address you wish to receive alerts at in the “Receiving Address” field (Figure 10) and click the [Add] button. 3. Click the [Save] button at the bottom of your screen. Repeat Steps 2 and 3 for each email address you wish to set up to receive notification alerts.
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 1. 2. (Figure 12) 4. 3. 5. 6. 7.
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 4. Setting up DDNS Service Dynamic Domain Name Service (DDNS) provides the capability for a networked device using the Internet Protocol Suite to notify a DDNS host to change the active DNS configuration of its hostnames or addresses.
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 g. h. . i. (Figure 16) f. Once you are logged in, click on the [Setup] tab at the right hand side of your screen (See Figure 8). This will generate a drop down menu on the left hand side of your Setup screen (See Figure 11). Choose the “DDNS Config” option from the menu and you will generate a DDNS Config dialog on the right of your screen (Figure 16). g.
Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 Questions or Comments? Contact Us: Mailing Address: Customer Service: DPS Inc. 8015 E. Crystal Dr. Anaheim, CA 92807 Phone: 877-998-3440 x 538 Email: cs@dpsi-usa.com Live Chat from our Website Website: Tech Support: http://www.q-see.com Fax: 714-998-3509 Phone: 877-998-3440 x 539 Email: ts@dpsi-usa.
Digital Peripheral Solutions, Inc. 8015 East Crystal Drive Anaheim, CA 92807 www.Q-See.com Q-See is a registered trademark of Digital Peripheral Solutions, Inc.
