BOX MERCHANT PRE-DELIVERY GUIDE This guide contains everything you need to know about the delivery and installation of your new QCA Spa.
Important Information Please make a record of the following information. It will be valuable if service is required. ....................................................................................... Spa Model: __________________________________________________ Spa Serial Number: __________________________________________ Date Purchased: ______________ Date Installed: _______________ .......................................................................................
Introduction Congratulations on the purchase of your new QCA Spa! With some advance preparation, delivery of your new spa will be a breeze. We’ve prepared this planning guide to provide you with the information necessary for you to be ready for your spa’s delivery. We recommend reading this guide completely prior to the scheduled delivery of your QCA Spa. Proper preparation and care of your new QCA Spa will give your family years of relaxation and enjoyment. .................................................
1. Things To Determine Before Spa Installation yyWill my spa be located inside or outside? yyHow much space do I have available for a spa? (Size of room, deck, or patio) yyWhat are the measurements of door openings, fence gates or deck stairs for getting your spa to its destination? yyWhat are the dimensions of the spa’s length, width, and depth to determine if it will pass through interior doors or exterior gates? yyWhat is the weight of the spa without water and when filled.
Commonly Asked Questions yyDo I need a building permit? Most cities and counties require permits for exterior construction and electrical circuits. Check with your county or city to see if a building permit is required for spa installation. yyDo I need a fence or a gate around my spa? Some communities have codes requiring residential barriers such as fencing and/or self closing gates on the property to prevent unsupervised access to a spa by children under five years of age.
2. Selecting The Best Location For Your Spa Indoors or outdoors, its up to you. But there are some things you will need to consider when determining your spa’s placement. Outdoor Spa Placement Outdoor spa placement, such as decks or concrete is common However, the spa can be placed on any solid, uniform, level surface. Do not place your spa on grass or bare ground. If placing your spa on a wooden deck, be sure to consider your spa’s weight (filled with water) and the weight bearing capacity of your deck.
DO NOT place your spa directly under or within 12 feet of overhead power, telephone or cable lines. Make sure the spa is positioned so you have full access to the equipment compartments located by the spa controls. Be sure to leave at least 30” around all sides and back panels for easy service access if needed. Many people choose to build their spa into a deck or patio with custom tile or wood built up to the top of the spa cabinet for a built-in look.
View Think about the direction you will be facing when sitting in your spa. Facing the exterior siding of your house would not be very enjoyable. Place your spa where you will be facing a special landscaped area of your yard or a lovely evening sunset. Keep Dirt and Debris Out of your Spa Check the location of trees and spill paths from gutters to see if wind or rain will sweep debris into your spa. Prevent dirt and foliage from being tracked into your spa by providing a concrete path.
Exhaust fans are rated by CFM’s (cubic feet per minute). The fan must be powerful enough to remove all the air in the room in 3 minutes. To determine what size fan you will need, measure the rooms length x width x height and divide by 3 = CFM’s. Example: 20’ x 10’ x 8’ = 1600 cubic ft. / 3 = 533 CFM’s. You would need at least a 533 CFM fan for this room. We do not recommend placing your spa directly on household carpet or a wood floor.
A spa filled with water is very heavy. Existing decks and concrete patios must be inspected by a licensed contractor to determine adequate support. Your base must have a minimum of 150 pounds per sq. ft. load bearing capacity. Add additional bracing if necessary. Place the spa on an elevated foundation so that water drains away from it. Proper drainage will keep components protected from rain and wet weather. New concrete patios must be a 4” minimum depth with reinforced wire placed in the concrete.
4. Plan The Delivery Of Your Spa Check the dimensions of your spa The Spa Specification chart on page 20 lists your spa model and its dimensions. Compare the dimensions to the width of gates, sidewalks, and doorways along the delivery route used to bring the spa into your yard. It may be necessary for you to remove a gate or partially remove a fence in order to provide an unobstructed passageway to the installation location.
Sample Spa Route Diagram 12
Plan your spa route Use the diagram to plan your spa route. Consider the following when planning your spa route: Check the width of gates (#1), doors, steps (#2) and sidewalks to make sure your spa will pass through unobstructed. You may have to remove a gate or part of a fence to allow for adequate width clearance. If the route will require a 90° turn, check the measurements at the turn to ensure the spa will fit.
5. Electrical Requirements Before Spa Delivery IMPORTANT When installed in the United States, the electrical wiring of this spa must meet the requirements of the National Electric Code (NEC) and any applicable state or local codes. The electrical circuit must be installed by an electrical contractor and approved by a local building/electrical inspector. Electrical setup before delivery of your spa 1. All 240 Volt spas must be permanently connected (hard wired) to the power supply.
4. The electrical supply for the spa must include a suitable rated switch or circuit breaker to open all ungrounded supply conductors to comply with Section 422-20 of the National Electric Code, ANSI/NFPA 70. The disconnecting means must be readily accessible to the spa’s occupant but installed at least 10 feet from the spa water. Check with local municipalities for additional code requirements. 5.
6. GFCI Wiring Diagram This diagram shows a “Three Wire Plus Ground” installation. It has a load Neutral connection, commonly required for spa’s containing both 120 and 240 volt equipment. They need the load neutral connection to produce the 120 volt. 7. Electrical Siemens GFCI Breaker Box Note This - The white Neutral wire from the back of the G.F.C.I. MUST be connected to an incoming Line Neutral. The internal mechanism of the G.F.C.I. requires this neutral connection. The G.F.C.I.
7. Electrical Installation Of Spa After Delivery Important Safety notice for all models! Proper grounding is extremely important. Hot R E D G R N Ground GREEN (GROUND) Hot B O X B L K BLK (HOT) RED (HOT) W H T WHITE (NEUTRAL) Neutral TB1 USE COPPER 240V WIRE MIN. 6AWG. 40A 60HZ QC 8000 VS 300 VS 501 VS 515 S Y S T E M CIRCUIT BOARD GROUND 1. To gain access to the spa’s control box, remove the cabinet panel on the front of the spa, under the spas topside control.
8.
9. Wiring Schematic VS 300/501/515 House Breaker Box W H T Hot B L K R E D Hot 240V 40A 60HZ G R N Ground B O X Neutral RED (HOT) BLK (HOT) GRN USE COPPER WIRE MIN. 6AWG. S Y S T E M CIRCUIT BOARD WHT GROUND G.F.C.I. Breaker Box Bottom View of G.F.C.I. (Square D) Front View of G.F.C.I.
10. QCA Spas Model Specifications Model Number Outside Dimensions Gallons Dry Weight Filled Weight Power in Volts/ Amps 0 91"x42"x29" 190 214 1734 120V/15Amp 0HSM 91"x42"x29" 190 214 1734 120V/15Amp 1P 80.5"x56.5"x30" 240 309 2229 120V/15Amp 2P 82"x79"x36" 475 563 4363 120V/15Amp 14P 80"x74"x30" 300 614 3113 120V/15Amp 1 80.5"x56.5"x30" 240 309 2500 120V/15Amp 10 88"x60"x29.
