QHY5 Mono/Color CMOS Camera manual QHY5用户手册 V1.
CONTENT 1)SAFETY PRECAUTIONS---------------------------2 2)STANDARD EQUIPMENT---------------------------3 3)CAMERA STRUCTURE AND INTERFACE CONNECTION----5 4) C A M E R A D R I V ER S I N ST A L L AT I O N AN D Q U I C K LY MASTERING -------------------------------------6 5)SERVICE TEMPERATURE AND HUMIDITY OF CAMERA---7 6)QHY5 CMOS CHIP READ-OUT MODE ----------------7 7)CLEAN THE SURFACE OF CMOS CHIP---------------7 8)QHY5 MECHIANICAL-----------------------------9 9)QHY5 BACK FOUCS LENGTH--------------------
STANDARD EQUIPMENT Make sure that the following items are included in your camera package. If anything is missing, contact the retailer from which you purchased the camera. 1 2 QHY5 Camera 3 M42*0.75 to 1.25 inch adapter USB cable 4 guiding cable Note: The attachment is supplied by dealers, Please contact the dealers to know what are sold.
Camera Interface 1: Camera Front Part 2：M42*0.75 inner screw 2 3：M28*0.5 1.25 inch filter interface 4：Guiding port 5: USB port CAMERA DRIVERS INSTALLATION AND QUICKLY MASTERING 1 1. Please download last QHY5 system driver from http://www.qhyccd.com/download.html (WINUSB 64/32version) This version support windowsXP,windowsVista and windows 7, 64 and 32bit version. 3 4 2. Run installer 5 3. Connect the camera to computer with USB cable 4. System will find new device.
SERVICE TEMPERATURE AND HUMIDITY OF CAMERA Service Temperature of this camera is from 20C/-4F to +30C/86F. Relative Humidity amount is from 0% to 90%. QHY5 CMOS CHIP READ-OUT MODE QHY5’s CMOS chip is single channel and progressive. The camera supports reading out non-compressed video. CLEAN THE SURFACE OF CMOS CHIP If dust coats the surface of the CMOS-it will impact the your images and possible create “dust donuts” and other artifacts.
QHY5 MECHIANICAL QHY5 BACK FOUCS LENGTH QHY5’s back focus is 12.
QHY5 SOFTWARE ABC COURSE QGVideo5T is the capture software for QHY5. It’s supports reading out non-compressed video/image data, and it is very suit for capturing solar, moon, or planets. 1. Run QGVideo5T, if the drivers of QHY5 has been installed correctly, and QHY5 has been connected with computer correctly, the software will note “CONNECTED” and run, if the QHY5 has been not installed correctly, the software will note “No Camera Detected” . 2.
Guiding by using QHY5 in MAXim DL QHY5 contains a guiding port, it can be used as a guiding ccd with ASCOM. QHY5 uses 1*1 bin and normal download speed default. It can use subframe mode to guide. 1. 2. 3. 4. 5. 6. 13 Connect the QHY5 and the equatorial mount’s guide spot. Run MAXim DL, choose View-Camera Control Window, choose Setup-Setup Camera-Camera Model-ASCOM-Advanced, in the ASCOM Camera Choose window, choose the CMOS QHY5 Camera, and click the Properties button, set Gain and Offset and so on.
Guiding by using QHY5 in PHD QHY5 Guiding Port Definition 1. QHY5 uses the ST-4 guiding port, you can watch the under picture to know detail. 2. 3. 4. 5. 6. 7. 15 Connect the QHY5 and the equatorial mount’s guide spot. Run PHD, choose Connect to Camera ( )ASCOM v5 camera-CMOS QHY5 CameraProperties, set Gain, click OK to return. Choose Mount-On-camera, and then click Connect to telescope ( ). Click to expose.
