HK316 User’s Manual Document version 1.
Safety Notices Before Installation or Use ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ It is required grounded well and the supply voltage shall be stable, and you must confirm that the voltage of the outlet provides shall be in line with the voltage marked on the label of the unit. Be sure not to sprinkle any liquid or fall any object into the unit. Be sure not to keep heavy, strenuous movement, shake & heavy strike away from the POS.
1. Applied range The HK316 terminal adopt open operating system, flexible component structure and standard peripherals. The products are suitable for the commercial enterprises, such as restaurants, supermarkets, and convenience stores to Internet –connected use or stand-alone use. The main components are standard parts, so the quality of the products is reliable, the system is easy to upgrade and the components are conveniently and easily maintained.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1、24V power input 2、Cash drawer interface 3、Serial port 4、printer 24V power 5、USB*2 6、USB*2 7、RJ45 8、Audio 9、Volume+ button 10、Volume - button 11、Brightness+ button 12、Brightness - button 13、TF card slot 14、Micro USB 15、USB 4
3. Mainboard Mainboard front layout: Ports and definition Ports 1.CON25 2.CON65 3.CON4 4.CON23 CON24 5.J8 J9 6.CON5 7.CON19 8.J10 9.CON31 10.CON18 11.CON61 12.CON58 13.CON7 14.CON8 Interface Serial port wafer1.25 1*8pin x1set Serial port 12PIN FPC socket Button board pin wafer2.0 2*6 pin x1set Serial port COM0 pin wafer2.0 2*5 pinx1set Serial port COM2 pin wafer2.0 2*5 pinx1set 1*3 wafer2.
Mainboard back layout Edp1 interface definition Pin No. Function Pin No.
EDP2 interface definition Pin No. Function Pin No.
4. Device Assembly and disassembly 1). Unscrew the two screw shown to remove the back shell of the base. 2).After removing the screw, pull at the back shell of the base according to the picture shows, and remove the back shell of the base. 3).
screen hinge and the second screen hinge respectively, and carefully pass the screen line through the line hole. Separate the main and auxiliary screen from the base respectively. 5).Remove the hinges of the host: Remove four screws according to the picture shows. Remove the hinges of the host and the hinges cover of the host separately. 6).Remove the extended interface cover: pull the expanded interface cover outward at the notch according to the picture shows, and remove it. 7).
8).Remove 7 screws according to the picture shows to remove the host fixed seat, so that the motherboard can be replaced and maintained. 5. Functional testing and parameter setting of peripherals In product test mode, magnetic stripe card test items are swiped by magnetic stripe card, and magnetic stripe card corresponding to the track shows "success" (three tracks, different magnetic stripe cards may store info into different tracks). As the following figure.
Contactless card test items In product test, with RFID card close to the back of the card reader, show "find * card" (Contactless card is divided into A card, B card, M card). As The following figure. Printer U-port printer, without setting baud rate, can use the normal detection of product test procedures. Cash drawer As shown below, for the item "CashBox ByCPU" in the product test, click "Click to Open Cashbox".
6. Environmental requirements Type State Voltage Environmental AC 100V-240V 50-60Hz Bipolar grounding 5℃ - 40℃ Temperature Optimal 40% - 90% 7.
Double Screen，Length×Width×Height：405*250*370； Main Flip Angle 0-45°，Second screen Flip Angle 0-30° High position +printer，Length×Width×Height：405*250*420 Self-service，Length×Width×Height：230*250*450 8. Open the box and check. 1) Before opening the box, check whether the box is in good condition, and whether there is any obvious damage. 2) The equipment must be installed by technical service person or distributors.
Start-up: When the adapter is connected, hold down the switch button on the right back side of the bottom of the machine for about 3 seconds. When the screen is on and the button indicator light is on, the startup can be realized. Shutdown: Press the switch button on the right back side of the bottom of the machine for about 3 seconds, and operate according to the screen prompt, which can realize shutdown and restart functions.
2) Load and change paper introduction a. Press the open button to open the paper bin cover, as shown below. If there are paper tubes in the paper warehouse, please take them out. b. Put the paper roll into the paper bin, pay attention to the correct direction of the paper roll.
c. Please take out a small amount of paper from the front of the roll and close the cover of the printer's paper bin d. Remove excess paper toward the side of the paper cut.
Width of paper：57.5±0.5mm / 79.5±0.5mm Outside Diameter of paper roll：Max 83mm Thickness of Thermal Paper：0.056 ~ 0.13mm 2) Recommendation of thermal Paper Model： Type FD210,PD150R,PD160R Manufacture OJI Paper CO., Notes： A. Please use the recommended paper roll or the same quality paper roll. The use of other types of paper roll may affect the printing effect and the life of the printing head. B.
10. Accessories No. Item Unit Quantity 1 POS terminal 1 2 Power adaptor 1 3 Power cable 1 Note FCC Statement： Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules.
