Electronic Lock Model: M15 Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com Quick start tip: 1.We are sincerely recommend you to scan the QR code below to watch our product installation and programming video on Youtube which will save your valuable time. 2.Our customer support team is providing video call guide service now,which will guide you to complete the lock installation and setups in minutes. Feel free to email us at support@kingforceusa.com to schedule your video call.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com Prepare the door and check dimensions If drilling a new door, use the supplied template and the complete door drilling instructions 1. 2. ba 60 or 70 mm ck se t 54 mm 3. 4. Measure to confirm the thickness of the door is the door edge is 1" (25 mm). between 1-3/8" and 2"(35mm and 50mm).
2 Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com Install the latch and strike 1 . Insert the latch bolt into the door. Make sure t he T-shaped hole is in the bottom position. up YES No adjustment is required. Proceed to next step. up NO Twist the latch and adjust the bolt length. (Make sure the latch bolt is retracted). YES NO NO up 2 . Install strike on the door frame. Make sure the hole in the door frame is drilled a minimum of 1"(25mm)deep.
3 Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com Install the exterior assembly cable YES NO Route the cable through the door below The key must be pulled out when installing. the bolt.and push the keypad onto the door.
4 Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com Install the interior assembly 3 1. Take off the mounting plate. Mounting plate Loose the 2 screws 2. Route cable through the bottom of mouting plate. 3. Tighten screws evenly. Note: please support exterior assembly during mounting plate installation. Cable 4. Ensure tight cable connection. 5. Tighten screws evenly. The smooth side of the plug should be at the bottom.
5 Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com Install the batteries and perform the door handing process Note:Do not use rechargeable batteries or Non-alkaline batteries. 1.Install 4 AA batteries in battery pack. T he b atte ries are no t inc luded. 2. Perform the door handing process. Press ,the latch bolt extends by itself. If the latch bolt extends or retracts not smoothly. please check the latch and re-install the lock.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com The Tuya APP is available for iOS and Android devices-free of charge. You can set up, operate and control all your Kingforce products with Tuya app. Download Tuya App Two methods to download Tuya App. F a cto ry de fa u lt se ttin g s Method 1： Scan the following QR code to download Tuta App.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com How to set up a new entrance Me Home Management Create a Home Add Member Step 1: Invite your members to family with invite code by Tuya account, Wechat and SMS. Step 2: Control smart lock (Two ways) ①The administrator: Home Member management Open mode Password Create a password to members. ②The users: Control smart lock by swiping phone.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com How should I do if I can’t connect to smart lock Restart the Bluetooth, and try again. How many passwords can be added It can be added for ten passwords.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com I 5 the keypad will be locked 90 seconds p exited 90 seconds for more than 5 seconds A factory reset will delete all codes associated with the lock. O pen t he b a t t e r y c o v e r . blue 5x Keep press holding set button more than 5 seconds until the lock short beeps 5 times and light flash blue 5 times. then the beeps 1 second and light flash green 1 times. the lock has been reset sucessful.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com System Alerts Alert button flashes red 3 times with 3 beeps. button flashes red 3 times with 3 beeps. Reason Solution Door jammed while attempting to lock. Manually re-lock door. If needed, reposition strike. Incorrect User Code ente red. Re-enter User Code. 5 incorrect User Codes entered within one minute. Re-enter User Code after 90 seconds keypad lock out. LED redlight when press Low battery. any button.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.
Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
