User's Manual
Table Of Contents
- 1 Read This First
- 2 Safety Information
- 3 Overview
- 4 Preparing the System
- Inserting a microSD Card
- Using the Stand
- Charging the System
- Connecting the Transducer
- Removing the Transducer
- Using the System On The Go
- Using the Wheel Brakes
- Placing the Transducer Holder
- Mounting the System to the System Cart
- Adjusting the System Cart Height
- Connecting an External Printer
- Tilting the System
- Unmounting the System From the System Cart
- Moving the System
- Outputting the System Display to an HDMI-Enabled TV or Monitor
- Supported External Printers
- 5 Using the System
- Turning On/Off the System
- Logging Into the System
- Launching the Main Screen
- Setting the System Time and Date
- Controlling the System
- Setting the System Language
- Identifying the Main Screen Layout
- Switching the Control Panel Pages
- Managing the System Power
- Managing Disk Space
- Network Configuration
- DICOM Configuration
- 6 Performing an Exam
- Starting a New Exam
- Adding a New Patient
- Loading a Worklist
- Selecting a Preset
- Setting the Transducer Orientation
- Selecting/Switching a Scan Mode
- Adjusting the Displayed Image
- Freezing an Image
- Adding Annotations
- Adding Measurements
- Saving and Printing the Image
- Reviewing the Image
- Exporting the Exam
- Managing the Exam List
- Ending the Exam
- 7 Using Image Controls
- 2D Mode Image Controls
- Overview
- Adjusting Gain
- Adjusting Frequency
- Adjusting Time Gain Compensation (TGC)
- Adjusting the Scan Depth
- Adjusting the Focus Depth, Focal Zone and Focal span
- Adjusting Dynamic Range
- Using Tissue Harmonic Imaging (THI)
- Adjusting Persistence
- Adjusting Sharpness and Smoothing
- Adjusting Gray Map
- Adjusting Chroma Map
- Adjusting Steer Angle
- Adjusting the Sector Width and Position
- Adjusting Power
- Using Trapezoidal Imaging
- Adjusting Density
- Using Compound Imaging
- Using ENV (Enhanced Needle Visualization)
- Color/CPA Mode Image Controls
- M-Mode Image Controls
- Spectral Doppler Mode Image Controls
- 2D Mode Image Controls
- 8 System Customization and Service
- Customizing Your System
- Configuring Security Policies
- Servicing your system
- Reinstalling Software
- Checking the Software Version
- Checking the System’s Serial Number
- Checking the Tablet’s Serial Number
- Checking the License Status
- Resetting User Settings
- Backing Up System Settings and Patient Data
- Restoring System Settings and Patient Data
- Resetting Your System
- Testing the System
- Exporting System Logs
- Reading the User Manual
- 9 Transducers
- 10 Transducer Care
- 11 System Maintenance
- 12 Appendix
InnoSight Ultrasound System
Adding Measurements
einnx
P6992-4, EN, 16/12/6
3 When the tracing is nearly done, release the cursor and the system completes the loop by drawing a
line from the current cursor position to the starting point
c
Angle
Measure an angle
1 Touch Angle A crosshair cursor appears on the image Drag the target cursor to the desired location
and release it to set the start point of measurement
2 Drag the first target cursor along one side of the desired area, and release it to draw the first line
3 Drag the second target cursor along the other side of the area, and release it to draw the second line
The angle between the two lines is then formed
d
IMT
Measure IMT (Intimal Media Thickness) of the carotid artery, which is useful for detecting early signs of
arteriosclerosis
1 Touch IMT A crosshair cursor appears on the image Drag the target cursor to the desired location and
release it to set the start point of measurement
2 Drag the target cursor to the other end of the desired area, and release it to set the end point of
measurement
e
Calculation Package
Perform a set of predefined measurements based on the scan mode/calculation method you select
1 Touch Calc to open the calculation package menu
2 Touch a desired calculation method The items to measure display in a list of order under the selected
method
3 Touch the first item and the screen displays the corresponding cursor Drag it to perform measurement
4 After you have finished with the measurement, touch the second item The first item is checked
automatically
with the measured result
Repeat step 3-4 to perform the rest of the measurements on the list
For measurement accuracy and precision in 2D measurement:
Linear distance measurement errors will be less than
Perimeter, and ellipse circumference measurement errors will be less than
Area measurement errors are related to the linear distance measurement and will be less than
1
Measuring in M-Mode
Distance
Measure the length between two horizontal lines that lean on two cursors The position of the vertical time
lines does not affect the distance measurement
1 Touch Distance A crosshair cursor with horizontal and vertical axes appears on the time series window
Drag the cursor to a desired start point on the vertical axis and release it
2 A second cursor appears Drag it to the end point on the vertical axis then release it to complete
measurement