iSR6142 Intelligent Storage Router Installation Guide SN0051102-00 A
S iSR6142 Intelligent Storage Router Installation Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
A iSR6142 Intelligent Storage Router Installation Guide Table of Contents 1 Introduction Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communications Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSR6142 Intelligent Storage Router Installation Guide S Chassis LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heartbeat LED (Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input Power LED (Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Fault LED (Amber) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chassis Controls . . . . . . . . . . . . . . . . . . . . . . . . . .
A 4 iSR6142 Intelligent Storage Router Installation Guide Installation Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Management Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iSR6142 Router Installation . . . . . . . . . . . . .
iSR6142 Intelligent Storage Router Installation Guide 6 S Removal/Replacement SFP Transceiver Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . Router Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A Log Messages Log Data. . . . . . . . . . . . .
A iSR6142 Intelligent Storage Router Installation Guide Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notification Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agent Start Up Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agent Shut Down Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network Port Down Notification. . . . . . . . . . . . . .
iSR6142 Intelligent Storage Router Installation Guide A-2 A-3 A-4 A-5 A-6 A-7 A-8 A-9 A-10 A-11 A-12 A-13 A-14 A-15 A-16 B-1 B-2 S iSCSI Driver—Informational Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fibre Channel Driver—Informational Log Messages. . . . . . . . . . . . . . . . . . . . . . . . User Modules—Informational Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FCIP—Informational Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Introduction This manual describes the features and installation of the QLogic iSR6142 Intelligent Storage Router (iSR-6142), also referred to as the iSR6142 router or simply router. Intended Audience This guide is for users who are responsible for installing, managing, and servicing the iSR6142 router and the storage area network (SAN) equipment to which it is attached.
S 1 – Introduction Safety ANSI SCSI – SCSI-3 Architecture Model (SAM), X3T10/994D/Rev 18, SCSI-3 Controller Command Set, X3T10/Project 1047D/Rev 6c. IEEE – 802.1Q Virtual LAN (VLAN), 802.1p Priority of Service, 802.3x Flow Control, 802.3ad Link Aggregation SCSI-3 Fibre Channel Protocol (SCSI-FCP), X3.269:1996 Fibre Channel Physical and Signaling Interface (FC-PH), X3.230:199 Fibre Channel 2nd Generation (FC-PH-2), X3.
A 1 – Introduction Communications Statements Federal Communications Commission (FCC) Class A Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
S 1 – Introduction Communications Statements CE Statement The CE symbol on the equipment indicates that this system complies with the EMC (Electromagnetic Compatibility) directive of the European Community (89/336/EEC) and to the Low Voltage (Safety) Directive (73/23/EEC).
A 1 – Introduction Laser Safety Information VCCI Class A Statement This is a Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. Laser Safety Information This product may use Class 1 laser optical transceivers to communicate over the fiber optic conductors. The U.S.
S 1 – Introduction Accessible Parts Accessible Parts The following field replaceable units (FRUs) are supported by the iSR6142 router: Small form-factor pluggable (SFP) optical transceivers License Agreements Refer to the QLogic Software End User License Agreement for a complete listing of all license agreements affecting this product. General Public License QLogic routers are powered by the Linux operating system.
A 1 – Introduction General Public License When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new programs, and that you know you can do these things.
1 – Introduction General Public License S translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this License – they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program).
A 1 – Introduction General Public License Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
1 – Introduction General Public License S 5. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 6.
A 1 – Introduction General Public License This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 9.
S 1 – Introduction General Public License ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
A 1 – Introduction Technical Support Yoyodyne, Inc., hereby disclaims all copyright interest in the program ’Gnomovision’ (which makes passes at compilers) written by James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library.
S 1 – Introduction Technical Support Contact Information Support Headquarters QLogic Corporation 4601 Dean Lakes Blvd Shakopee, MN 55379 USA QLogic Web Site www.qlogic.com Technical Support Web Site support.qlogic.com Technical Support Email support@qlogic.com Technical Training Email tech.training@qlogic.com North American Region Email support@qlogic.com Phone +1-952-952-4040 Fax +1-952-687-2504 Europe, Middle East, and Africa Region Email emeasupport@qlogic.
2 General Description This section describes the following features and capabilities of the iSR6142 router: Router Capabilities (see page 2-2) Licensed Features (see page 2-2) Remote SAN Island Connectivity (see page 2-4) Local SAN Island Connectivity (see page 2-6) FCIP - Fibre Channel over IP (see page 2-6) Chassis LEDs (see page 2-6) Chassis Controls (see page 2-7) Fibre Channel Ports (see page 2-9) Fibre Channel SFP Transceivers (see page 2-11) iSCSI/Gigabit Ether
S 2 – General Description Router Capabilities Router Capabilities The iSR6142 is a bi-directional FC-to-iSCSI router.
A 2 – General Description Licensed Features Provides failover and failback between two gigabit Ethernet links. Allows data compression. This is very useful when data round-trip latencies between two routers exceed more than 50 ms or long distance link rate is equal or less than 4500 Mbits/sec (DS-3 line rate) SmartWrite is an optional feature that requires purchasing a license key.
2 – General Description Remote SAN Island Connectivity S Remote SAN Island Connectivity The iSR6142 router supports inter-connecting remote SAN islands (see Figure 2-2). Figure 2-2 Remote SAN Island Connectivity This configuration has the following additional requirements: At least one FC port of iSR6142 connected to FC SAN. Accessibility between the iSCSI/GE (Gigabit Ethernet ports on the router) port IP addresses of remote router and iSCSI/GE port IP addresses of local routers.
A 2 – General Description Remote SAN Island Connectivity To map remote FC devices to local SAN: 1. If the remote router is not already associated with a local router, use either the Add Remote Router wizard (see the iSR6142 Router Manager User's Guide) or the CLI command remotepeer add (see the iSR6142 Router CLI User's Guide) to associate the two routers with each other. 2.
S 2 – General Description Local SAN Island Connectivity Local SAN Island Connectivity You can use either the the SANsurfer Router Manager (see the iSR6142 Router Manager User's Guide) or Command Line Interface (CLI) (see the iSR6142 Router CLI User's Guide) to map any of the following connections: iSCSI server to an FC device (target) FC server to an iSCSI device (target) FC server from one SAN to FC target on another SAN CAUTION! When adding multiple routers in the same physical SAN, you must
A 2 – General Description Chassis Controls Heartbeat LED (Green) The heartbeat LED blinks once a second as long the router firmware is operational. Input Power LED (Green) The power LED shows the voltage status at the router logic circuit board. During normal operation, this LED lights up to show that the router logic circuit board is receiving the DC voltage from the power supply. System Fault LED (Amber) The system fault LED lights up to show that a fault exists in the router firmware or hardware.
2 – General Description Chassis Controls S Maintenance Button The maintenance button is a multifunction momentary switch on the front panel.
A 2 – General Description Fibre Channel Ports The IP address set by this method is not persistent; to make the change persistent, use the command line interface (CLI) or the SANsurfer Router Manager to set the IP address. For more information, see the iSR6142 Router Manager User's Guide or the iSR6142 Router CLI User's Guide.
S 2 – General Description Fibre Channel Ports Each port is served by a small form-factor pluggable (SFP) optical transceiver and is capable of 1-Gbps or 2-Gbps transmission. SFPs are hot-pluggable. FC ports can self-discover both the connection type and transmission speed when connected to public devices or switches. The port LEDs are located to the right of their respective ports and provide status and activity information.
A 2 – General Description Fibre Channel SFP Transceivers Fibre Channel SFP Transceivers The iSR6142 router supports SFP optical transceivers for the Fibre Channel ports. A transceiver converts electrical signals to and from optical laser signals to transmit and receive data. Duplex fibre optic cables plug into the transceivers, which then connect to the devices. The Fibre Channel ports are capable of transmitting at 1-Gbps or 2-Gbps; the transceiver must also be capable of delivering these rates.
2 – General Description iSCSI/Gigabit Ethernet Port LEDs S iSCSI/Gigabit Ethernet Port LEDs The iSCSI/gigabit Ethernet ports shown in Figure 2-7 are RJ-45 connectors that provide connection to an Ethernet SAN through a 10/100/1000 Base-T Ethernet cable. The ports are labeled GE1 and GE2. These ports have two LEDs – the link status LED (green) and the activity LED (also green). The link status LED lights up continuously after the router establishes an Ethernet connection.
A 2 – General Description Serial Port Serial Port The iSR6142 router is equipped with an RS-232 serial port for maintenance purposes. Figure 2-9 shows the serial port location. It is labeled IOIOI. You can manage the router through the serial port using the CLI. Figure 2-9 Serial Port The serial port connection requires a standard, eight-wire Ethernet cable and the RJ45-to-DB9F adapter (supplied) to convert the Ethernet RJ45 connector to a female DB9 connector.
S 2 – General Description Serial Port Table 2-4.
3 Planning This section describes how to plan for the iSR6142 router.
S 3 – Planning Device Access Device Access Consider device access needs within the FC and iSCSI SANs. Access to an FC device is controlled by mapping FC device to specific iSCSI initiators. FC devices may be mapped to more than one initiator. Giving multiple initiators access to an FC device requires access management. Fibre Channel The Fibre Channel ports automatically discover all FC target devices, whether connected directly (loop) or by fabric (switch).
A 3 – Planning iSCSI/Gigabit Ethernet Performance Distance Consider the physical distance between Fibre Channel devices. Choose SFP transceivers that are compatible with the cable type and distance you need. Each Fibre Channel port is supported by a data buffer with a three-credit capacity; that is, three maximum sized frames. For fibre optic cables, this enables full bandwidth over the following approximate distances: 5 kilometers at 1 Gbps (0.6 credits/Km) 2.5 kilometers at 2 Gbps (1.
S 3 – Planning Performance Tuning Distance Consider the physical distance between routers. This is usually measured in round-trip delay. Round-trip delay ranges anywhere from less than 1 ms to as great as 250 ms. Performance Tuning Properly configuring the router maximizes its performance. Knowing the round-trip delay (distance) between routers and the WAN effective data rate (connection type) allows you to tune the routers for optimal performance.
A 3 – Planning Performance Tuning Table 3-2. T3 / DS-3 – 45 Mbits/Sec Round Trip Delay (ms) Total Window Size (bytes) Scaling Factor 250 1 MB 5 100 512 K 4 50 256 K 3 25 128 K 2 20 128 K 2 15 64-128 K 1 or 2 10 64 K 1 5 32 K 0 2.5 32 K 0 1 or less 32 K 0 Table 3-3.
S 3 – Planning Performance Tuning Table 3-4. OC-1 – 50 Mbits/Sec Round Trip Delay (ms) Total Window Size (bytes) Scaling Factor 250 1 MB 5 100 512 K 4 50 256 K 3 25 128 K 2 20 128 K 2 15 64-128 K 1 or 2 10 64 K 1 5 32 K 0 2.5 32 K 0 1 or less 32 K 0 Table 3-5. OC-3 – 150 Mbits/Sec 3-6 Round Trip Delay (ms) Total Window Size (bytes) Scaling Factor 250 1 MB 5 100 1 MB 5 50 1 MB 5 25 512 K 4 20 512 K 4 15 256 K 3 10 256 K 3 5 128 K 2 2.
A 3 – Planning Topology Table 3-6. OC-12 and Above – 621 Mbits/Sec Round Trip Delay (ms) Total Window Size (bytes) Scaling Factor 250 1 MB 5 100 1 MB 5 50 1 MB 5 25 1 MB 5 20 1 MB 5 15 1 MB 5 10 1 MB 5 5 512 K 4 2.5 256 K 3 1 or less 64 K 1 Topology The iSR6142 router supports two distinct topologies: interconnecting local SANs (see Figure 3-1) and interconnecting remote SANs (see Figure 3-2).
3 – Planning Fibre Channel Switch Ports and Zoning Requirements S Figure 3-2 WAN Topology - Remote SAN Interconnect Fibre Channel Switch Ports and Zoning Requirements The iSR6142 FC ports are configured as loop ports. Therefore, the FC switch port, (where iSR6142 FC port is connected) must be configured to support a loop topology such as fibre loop port (FL-Port) or generic port (G-Port). The iSR6142 uses its local FC ports for discovering local FC devices in the SAN.
A 3 – Planning Management Management The SANsurfer Router Manager application and CLI run on a management workstation that enables you to configure, control, and maintain the router. Support platforms include Windows, Solaris, and Linux. The router supports the following management interfaces: SANsurfer Router Manager – Graphical user interface application, which runs on a management workstation (see the iSR6142 Router Manager User's Guide).
S 3 – Planning Services Services You can configure the iSR6142 router to suit the demands of your environment using a variety of router services. Familiarize yourself with the following router services and determine which ones you need: Telnet – Enables router management over a telnet connection. Router management – Provides for out-of-band router management using the SANsurfer Router Manager.
4 Installation This section describes how to install and configure an iSR6142 router. It also includes firmware installation instructions.
S 4 – Installation iSR6142 Router Installation Table 4-1. Management Workstation Requirements (Continued) Item Description Processor 500 MHz or faster Hardware CD-ROM drive, RJ-45 Ethernet port, RS-232 serial port (optional) Internet browser One of the following: Microsoft Internet Explorer 5.0 and later Netscape Navigator® 4.72 and later Mozilla® 1.
A 4 – Installation iSR6142 Router Installation Figure 4-1 iSR6142 Router and Accessories To install the iSR6142 router: 1. Complete the pre-installation checklist (see page 4-4). 2. Mount the router (see page 4-4). 3. Install the transceivers (see page 4-5). 4. Connect the management workstation to the router (see page 4-5). 5. Configure the management workstation (see page 4-5). 6. Install the management application (see page 4-7). 7. Start the management application (see page 4-8). 8.
S 4 – Installation iSR6142 Router Installation Pre-installation Check List During the initial configuration process, the system prompts you for the parameters listed in Table 4-2. Fill out the table before installation to expedite the configuration process. Table 4-2.
A 4 – Installation iSR6142 Router Installation Install the Transceivers The router supports a variety of SFP transceivers. To install a transceiver, insert the transceiver into the port and gently press until it snaps in place. To remove a transceiver, gently press the transceiver into the port to release tension, then pull the release tab or lever and remove the transceiver. Different transceiver manufactures have different release mechanisms. Consult the documentation of your transceiver.
S 4 – Installation iSR6142 Router Installation Setting the Workstation IP Address The IP address of a new router is 10.0.0.1. To ensure that your workstation is configured to communicate with the 10.0.0 subnet, refer to the following instructions for your workstation: Steps for different versions of Windows vary. For a Windows 2000 workstation, do the following: a. From the Windows Start menu, select Settings>Control Panel>Network and Dial-up Connections. b. Click Make New Connection. c.
A 4 – Installation iSR6142 Router Installation For Linux: a. Set up minicom to use the serial port. Create or modify the /etc/minirc.dfl file with the following content: pr portdev/ttyS0 pu minit pu mreset pu mhangup pr portdev/ttyS0 specifies port 0 on the workstation. Choose the pr setting to match the workstation port to which you connected the router. b. Verify that all users have permission to run minicom. Review the /etc/minicom.
S 4 – Installation iSR6142 Router Installation Linux Installation Perform the following steps to install the SANsurfer Router Manager application from the QLogic website to a Linux workstation: 1. Go to the QLogic download site: http://support.qlogic.com/support/drivers_software.aspx 2. Select the Intelligent Storage Routers icon. 3. Select iSR6142 in the product selection window and click Go. 4.
A 4 – Installation iSR6142 Router Installation Connect the Router to AC Power WARNING!! This product is supplied with a three-wire power cable and plug for the user’s safety. Use this power cable in conjunction with a properly grounded outlet to avoid electrical shock. An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the router chassis. It is the customer’s responsibility to ensure that the outlet is correctly wired and grounded to prevent electrical shock.
S 4 – Installation iSR6142 Router Installation Configure the Router You can configure the router using the SANsurfer Router Manager application or the command line interface (CLI). The SANsurfer Router Manager provides a Configuration Wizard you can use to configure the GE ports. If either of the router’s GE ports have not been configured (IP address is 0.0.0.0), the Configuration Wizard starts automatically when the SANsurfer Router Manager first connects with the router.
A 4 – Installation Firmware Installation Cable Devices to the Router Connect cables to the SFP transceivers and their corresponding devices. Devices can have small form-factor pluggable (SFP) or small form-factor (SFF) transceivers or gigabit interface converters (GBIC). Lucent (LC)-type duplex fiber optic cable connectors are designed for SFP transceivers, while subscriber-connector (SC)-type connectors are designed for GBICs.
S 4 – Installation Firmware Installation Using the CLI to Install Firmware To use the CLI to install the firmware, transfer the firmware image file from a workstation to the router. Then use the CLI image unpack command to install the new firmware image: 4-12 1. At the workstation prompt, use the ftp command to go to the location on the router where you want to transfer the firmware image. For example: C:\fwImage>ftp 172.17.137.190 Connected to 172.17.137.190. 220 (none) FTP server (GNU inetutils 1.4.
A 4 – Installation Firmware Installation 7. Type the following command from the router, where x stands for the firmware image name: image unpack isr-6142-2_2_0_x.bin The following message displays: Unpack Completed. Please reboot the system for FW to take affect. 8. Type reboot. The following message displays: Are you sure you want to reboot the System (y/n): 9. Type y to reboot the system.
4 – Installation Firmware Installation S Notes 4-14 SN0051102-00 A
5 Diagnostics and Troubleshooting Diagnostic information about the router is available through the chassis LEDs and the port LEDs. Diagnostic information is also available through the Router Manager and CLI event logs and error displays.
5 – Diagnostics and Troubleshooting Power-On Self-Test Diagnostics S Input Power LED is Off The input power LED lights up to show that the router logic circuitry is receiving proper voltages. If the input power LED is off, do the following: Inspect power cord and connectors. Is the cord unplugged? Is the cord or connector damaged? Yes – Make necessary corrections or repairs. If the condition remains, continue. No – Continue. Inspect AC power source.
A 5 – Diagnostics and Troubleshooting LED Blink Patterns LED Blink Patterns The heartbeat and system fault LEDs show the operational status of the router. When the POST completes with no errors, the heartbeat LED will blink once every second. When the router is in maintenance mode, the heartbeat and system fault LEDs are on continuously. All other system fault blink patterns show critical errors. The heartbeat LED shows an error blink pattern for the conditions listed in Table 5-1. Table 5-1.
S 5 – Diagnostics and Troubleshooting LED Blink Patterns Management Port IP Address Conflict Blink Pattern The system fault LED generates a four-blink pattern (once per second) followed by a two second pause when the router detects an IP address conflict on the management Ethernet port. You can clear the IP address conflict blinking using the CLI or the Router Manager. Use the beacon OFF function.
A 5 – Diagnostics and Troubleshooting Recovering a Router Recovering a Router You may have to recover a router for one of the following reasons: The password was changed and has been forgotten. The router’s management IP address is unknown. To recover the router’s password, reset the password to the default by using the maintenance button (see page 2-8).
5 – Diagnostics and Troubleshooting Recovering a Router S Notes 5-6 SN0051102-00 A
6 Removal/Replacement This section describes the removal and replacement procedures for the following field replaceable units (FRU): SFP transceivers The router (see page 6-2) SFP Transceiver Removal and Replacement You can remove and replace the SFP transceivers while the router is operating without damaging the router or the transceiver. However, doing so will interrupt transmission on the affected port until the transceiver is installed.
6 – Removal/Replacement Router Removal and Replacement S Router Removal and Replacement Before you can remove and replace the router, you must turn off the power to the router and disconnect its power cable. The router will lose all the Fibre Channel and iSCSI connections. Removal To remove and replace a router, perform the following steps, as applicable: 1. Make sure all traffic (I/O operations to the router) subsides at the iSCSI initiator systems. 2.
A Log Messages This appendix provides reference material on messages logged to a file. You can retrieve these message logs using either the command line interface (CLI) (see the iSR6142 Router CLI Users Guide) or the Router Manager (see the iSR6142 Router Manager Users Guide). Log Data The message log is persistent, maintained across router power cycles and reboots.
S A – Log Messages Informational Log Messages Application Modules The application modules generate the informational log messages listed in Table A-1 and described following the table. Table A-1. Application Modules—Informational Log Messages ID A-2 Log Message No. 53254 System (router) Booting up 6 53357 QLBA_ProcessTpb: De-compression failed. Disabling compression temporarily 109 54274 QLFC_Login: Origin 0x%x, VP Index 0x%x, Id 0x%x 1026 54275 QLFC_Login: Port ID %.2x%.2x%.
A A – Log Messages Informational Log Messages Table A-1. Application Modules—Informational Log Messages (Continued) SN0051102-00 A ID Log Message No. 54963 QLIS_SetDdbEntryContinue:[%d:%d] Remote system connection established 1715 54986 QLIS_HandleSessionTimer: Re-enabling compression 1738 55299 QLSC_CollectBUVUIO: Freeing dead TRB: State 0x%02X, AbortReason %d, Flags 0x%02X 2051 6 Router is booting up. 109 De-compression failed and will be temporarily disabled.
S A – Log Messages Informational Log Messages 1700 iSCSI connection closed. 1715 Remote system connection established using DDB d:d. 1738 Re-enabling compression. 2051 TRB freed, State xx, Abort Reason d, Flags xx. iSCSI Driver The following informational log messages are common to both iSCSI ports: 1 (GE1) and 2 (GE2). The messages are listed in Table A-2 and described following the table.
A A – Log Messages Informational Log Messages Fibre Channel Driver The following informational log messages are common to both Fibre Channel ports: 1 (FC1) and 2 (FC2). The messages are listed in Table A-3 and described following the table. Log messages beginning with #0 denote Fibre Channel port 1 (FC1). Log messages beginning with #1 denote Fibre Channel port 2 (FC2). Table A-3. Fibre Channel Driver—Informational Log Messages ID SN0051102-00 A Log Message No.
S A – Log Messages Informational Log Messages 768 FCIP - Fibre Channel link up occurred. Event status is reported, as is the contents of the FC processor’s mailbox 1 register. 769 FCIP - Fibre Channel link down occurred. 770 FCIP - Fibre Channel link up occurred. Event status is reported, as is the RunTimeMode (0 = loop, 1 = point-to-point). User Modules The user modules generate the log messages listed in Table A-4 and described in the following table. Table A-4.
A A – Log Messages Informational Log Messages Table A-4. User Modules—Informational Log Messages (Continued) SN0051102-00 A ID Log Message No. 151903 qapimaptargettoinitiator_1_svc: Localmap added to target device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x 351 151904 qapiunmaptargettoinitiator_1_svc: Localmap removed for initiator device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x 352 151905 qapiunmaptargettoinitiator_1_svc: Localmap removed to target device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.
S A – Log Messages Informational Log Messages 348 Remotemap removed for local FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx. 349 Remotemap removed for remote FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx. 350 Localmap added for FC initiator WWPN xx.xx.xx.xx.xx.xx.xx.xx. 351 Localmap added to FC target device WWPN xx.xx.xx.xx.xx.xx.xx.xx. 352 Localmap removed for FC initiator. 353 Localmap removed to FC target device. 354 Localmap added for iSCSI initiator "iqn.dddd-dd.ttt.ttt.ttt.......".
A A – Log Messages Informational Log Messages TOE Driver The TOE driver generates the informational log messages listed in Table A-6 and described following the table. Table A-6. TOE—Informational Log Messages ID 217350 262 Log Message QL3022:eth%x: Interface is down No. 262 The GigE interface d (0 or 1) used for an FCIP route is down. System The system modules generate the informational log messages listed in Table A-7 and described following the table. Table A-7.
S A – Log Messages Error Log Messages Error Log Messages The following sections list and describe the error log messages by reporting module: “Application Modules” on page A-10 “iSCSI Driver” on page A-18 “Fibre Channel Driver” on page A-20 “User Modules” on page A-22 “System” on page A-25 Application Modules The application modules generate the error log messages listed in Table A-8 and described following the table. Table A-8.
A A – Log Messages Error Log Messages Table A-8. Application Module—Error Log Messages (Continued) ID SN0051102-00 A Log Message No. 41257 QLIS_LoginPduContinue: Invalid initiator name. Initiator: 297 41265 QLIS_LoginPduContinue: Target not configured for Portal 305 41267 QLIS_LoginPduContinue: Target not found.
S A – Log Messages Error Log Messages Table A-8. Application Module—Error Log Messages (Continued) ID A-12 Log Message No. 41771 QLBI_GetLunList: Lun allocation failed for LunId %d 811 41994 QLFC_Login: VpIndex (%d) out of range 1034 41995 QLFC_Login: VP Index 0x%x not configured 1035 42002 QLFC_Login: Can't open connection 1042 42024 QLFC_Logout: No active path to device. WWPN: %.2X%.2X%.2X%.2X%.2X%.2X%.2X%.
A A – Log Messages Error Log Messages Table A-8. Application Module—Error Log Messages (Continued) ID SN0051102-00 A Log Message No.
S A – Log Messages Error Log Messages A-14 7 NULL doorbell routine for unloaded drivers. When a driver is unloaded, the doorbell routine is redirected to this NULL routine. 36 Processing unsupported ordered tag task management command. 44 Processing unsupported head-of-queue task management command. 98 Unable to create an object for the target device: exceeded the maximum number of target devices. 100 Unable to create an object for the target node: exceeded the maximum number of target devices.
A SN0051102-00 A A – Log Messages Error Log Messages 323 iSCSI Login PDU was received with a TSIH out of range. This would occur if the iSCSI initiator attempting the login failed to used the TSIH value provided in the Target Login Response PDU (router is target) in subsequent login PDUs. 324 iSCSI Login PDU was received with an invalid TSIH value. The TSIH is invalid because there is no session with that TSIH value.
S A – Log Messages Error Log Messages A-16 1034 Login attempted using Fibre Channel virtual port (VP) index that is out-of-range (range = 0–31). Index reported in log message. 1035 Login attempted using Fibre Channel VP index that has not been configured. Operation attempted on an unconfigured VP. 1042 Attempting login but Fibre Channel connection cannot be opened. 1064 Attempting logout of device for which there is no active path (WWPN not found).
A SN0051102-00 A A – Log Messages Error Log Messages 2311 FCIP incoming frame: Got Status aborted pTrb->pBufDescList[0]:%p Trb Direction:0x%x. 2312 FCIP system error. 2313 FCIP system error: QLOP_IssuePortEnable failed. 2320 FCIP handle Teb: Driver Fatal error. 2321 FCIP configure portal: Find portal object failed for QLUT_TYPE_FC, PortId (%d). 2322 FCIP configure portal: QLFCIP_ConfigPortal: Invalid PortId for FCIP link PortID(%d). 2323 FCIP allocate TRB pool: Allocation failed (size 0x%x).
S A – Log Messages Error Log Messages iSCSI Driver The following error log messages are common to both iSCSI ports, 1 (GE1) and 2 (GE2). They are listed in Table A-9 and described following the table. Log messages beginning with #0 denote iSCSI port 1 (GE1). Log messages beginning with #1 denote iSCSI port 2 (GE2). Table A-9. iSCSI Driver—Error Log Messages ID A-18 Log Message No.
A A – Log Messages Error Log Messages 329 The iSCSI processor failed the external loopback test. 337 The iSCSI processor command to disable a GE port failed. 513 The iSCSI processor could not connect with the iSCSI name server (iSNS). 849 The iSCSI processor reported that the iSCSI port NVRAM contains invalid data (checksum error). 859 The iSCSI processor reported a link down condition. 928 The driver failed to receive a heartbeat from the iSCSI processor for the specified number of seconds.
S A – Log Messages Error Log Messages Fibre Channel Driver The following error log messages are common to both Fibre Channel ports, 1 (FC1) and 2 (FC2). They are listed in Table A-10 and described in this section. Log messages beginning with #0 denote Fibre Channel port 1 (FC1) and log messages beginning with #1 denote Fibre Channel port 2 (FC2). Table A-10. Fibre Channel Driver—Error Log Messages A-20 ID Log Messages No.
A A – Log Messages Error Log Messages Table A-10. Fibre Channel Driver—Error Log Messages (Continued) ID SN0051102-00 A Log Messages No. 107254 #%d: QLUpdateSinglePortCont 0x%x: out of slots in host database 758 107267 #%d: QLFcipIsrEventHandler: System error event (%x), MB1=%x, MB2=%x, MB3=%x, MB4=%x, MB5=%x, MB6=%x, MB7=%x 771 87 The FC processor received a SCSI command for an unknown target path or has run out of resources to execute additional commands.
S A – Log Messages Error Log Messages 582 The drivers host (initiator) database is full. 758 No slots available in host database. 771 FCIP system error event. User Modules The user modules generate the error log messages listed in Table A-11 and described following the table. Table A-11. User Modules—Error Log Messages ID A-22 Log Message No.
A A – Log Messages Error Log Messages Table A-11. User Modules—Error Log Messages (Continued) ID SN0051102-00 A Log Message No.
S A – Log Messages Error Log Messages A-24 21 Failed memory allocation for Get LUN List API. 22 Failed memory allocation for Get Presented Targets List API. 23 Failed memory allocation for Get LUN Mask API. 24 Failed memory allocation for Initiator API. 25 Failed memory allocation for Target Device API. 32 Failed memory allocation for FC Target API. 33 Failed memory allocation for System Status API. 34 Failed memory allocation for Diagnostic API.
A A – Log Messages Fatal Log Messages System The system modules generate the error log messages listed in Table A-12 and described following the table. Table A-12. System—Error Log Messages ID Log Message No. 237572 "Failed to kill sys killer %d\n" 4 237573 "Temperature over high threshold %d\n" 5 4 Failed to kill system task. 5 Reporting router exceeds maximum operating temperature.
S A – Log Messages Fatal Log Messages Table A-13. iSCSI Driver—Fatal Log Messages (Continued) ID A-26 Log Message No.
A A – Log Messages Fatal Log Messages Table A-13. iSCSI Driver—Fatal Log Messages (Continued) ID SN0051102-00 A Log Message No. 70836 #%d: QLStartFw: Invalid Fw loader state 0x%x 1204 70837 #%d: QLStartFw: Load Fw loader timeout 1205 20 iSCSI processor SRAM test failed. 21 iSCSI processor failed diagnostic reboot. 22 iSCSI processor failed NVRAM diagnostic. 23 iSCSI processor failed DRAM diagnostic. 24 iSCSI processor failed to return diagnostic results.
S A – Log Messages Fatal Log Messages 978 iSCSI processor reboot failed. 1152 iSCSI processor NVRAM invalid (checksum error). 1203 iSCSI FLASH (NVRAM) command failed. 1204 iSCSI firmware loader invalid state. 1205 iSCSI failed to load firmware in time allotted. FC Driver The following fatal log messages are common to both Fibre Channel ports, 1 (FC1) and 2 (FC2). They are listed in Table A-14 and described following the table. Log messages beginning with #0 denote Fibre Channel port 1 (FC1).
A A – Log Messages Fatal Log Messages Table A-14. Fibre Channel Driver—Fatal Log Messages (Continued) SN0051102-00 A ID Log Message No.
S A – Log Messages Fatal Log Messages 292 FC processor paused due to RAM parity error. 316 FC processor system error. 346 Response queue entry contains an invalid handle. 347 FCIP: Response queue entry contains an invalid buffer type. 348 FCIP: Response queue entry contains an invalid entry type. 349 FCIP: Response queue entry contains an invalid handle. 352 FC processor external SRAM parity error count exceeded limit: FC port disabled. 355 FC processor heartbeat failed.
A A – Log Messages Fatal Log Messages System The system modules generate the fatal log messages listed in Table A-16 and described following the table. Table A-16. System—Fatal Log Messages SN0051102-00 A ID Log Message No. 233473 "memory monitor: Detected Uncorrectable Ecc %08lx system is rebooting in 5 secs\n" 1 233474 "Failed to register interrupt handler!\n" 2 233475 "%s class_simple_create failed\n" 3 1 Uncorrectable memory error detected at address provided in log message.
A – Log Messages Fatal Log Messages S Notes A-32 SN0051102-00 A
B Simple Network Management Protocol (SNMP) Introduction Simple network management protocol (SNMP) provides monitoring and trap functions for managing the router through third-party applications that support SNMP. The router firmware supports SNMP versions 1 and 2 and a QLogic (see page B-3). You may format the traps using SNMP version 1 or 2 (see page B-11).
S B – Simple Network Management Protocol (SNMP) Introduction Table B-1. SNMP Properties (Continued) Parameter Description System contact Specifies the name of the person to be contacted to respond to trap events. The name can be up to 64 characters excluding the number sign (#), semicolon (;), and comma (,). The default is undefined. Authentication traps Enables or disables authentication trap generation in response to authentication failures. The default is disabled.
A B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) Management Information Base (MIB) The following sections describe the QLogic management information base (MIB). The MIB consists of four object groups: System Information Network Port Table Fibre Channel Port Table Fibre Channel Port Table System Information The system information objects provide the system serial number, version numbers (hardware/software/agent), and number of ports (FC/GE).
S B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrNoOfGbEPorts Syntax Unsigned32 Access Read-only Description The number of gigabit Ethernet ports on the system. qsrAgentVersion Syntax SnmpAdminString Access Read only Description The version number of the agent software on the system. Network Port Table The network port table contains a list of network ports that are operational on the router.
A B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrNetMask InetAddress qsrGateway InetAddress qsrMacAddress MacAddress qsrNwLinkStatus QsrLinkStatus qsrNwLinkRate QsrLinkRate qsrNwPortRole Syntax QsrPortRole Access Not accessible Description The operational role of this port: management port, iSCSI port, a TOE. qsrNwPortIndex Syntax Unsigned32 Access Not accessible Description A positive integer indexing each network port in a given role.
B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) S qsrNetMask Syntax InetAddress Access Read only Description The subnet mask for this port. qsrGateway Syntax InetAddress Access Read only Description The gateway for this port. qsrMacAddress Syntax IMacAddress Access Read only Description The MAC address for this port. qstNwLinkStatus Syntax QsrLinkStatus Access Read only Description The operational link status for this port.
A B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrFcPortEntry Syntax QsrFcPortEntry Access Not accessible Description Each entry (row) contains information about a specific FC port.
B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) S qsrFcPortWwn Syntax PhysAddress Access Read only Description The world-0wide name for this port. qsrFcPortId Syntax PhysAddress Access Read only Description The interface's 24-bit FC address identifier. qsrFcPortType Syntax Unsigned32 Access Read only Description The type of FC port, as indicated by the use of the appropriate value assigned by IANA. The IANA-maintained registry for FC port types can be found at: www.iana.
A B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrSensorEntry Syntax QsrSensorEntry Access Not accessible Description Each entry (row) corresponds to a single sensor.
B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) S qsrSensorValue Syntax Integer32 Access Read only Description The current value of the sensor. qsrUpperThreshold Syntax Integer32 Access Read only Description The upper-level threshold for this sensor. qsrLowerThreshold Syntax Integer32 Access Read only Description The lower-level threshold for this sensor.
A B – Simple Network Management Protocol (SNMP) Notifications Notifications The router provides the following notification types: Notification Objects Agent Start Up Notification Agent Shut Down Notification Network Port Down Notification Fibre Channel Port Down Notification Sensor Notification Generic Notification The following sections describe these notifications and objects they use. Notification Objects This section defines the objects used in notifications.
B – Simple Network Management Protocol (SNMP) Notifications S Agent Start Up Notification The agent startup notification indicates that the agent on the router has started running. qsrAgentStartup uses the following object: qsrEventTimeStamp Agent Shut Down Notification The agent shut down notification indicates that the agent on the router is shutting down.
A B – Simple Network Management Protocol (SNMP) Notifications Sensor Notification The sensor notification indicates that the state for the specified sensor is not normal. When the sensor returns to the normal state, this event is sent with the qsrEventSeverity object set to clear. qsrSensorNotification uses the following objects: qsrSensorValue qsrSensorState qsrEventTimeStamp qsrEventSeverity Generic Notification The generic notification reports events other than the defined event types.
B – Simple Network Management Protocol (SNMP) Notifications S Notes B-14 SN0051102-00 A
A iSR6142 Intelligent Storage Router Installation Guide Index A AC power 4-9 Accessible parts 1-6 Accessories 4-3 Application error log A-10 log messages A-2 B Bandwidth, FC devices 3-3 Boot image, selecting 2-8 C Capabilities, router 2-2 CE statement 1-4 Chassis controls 2-7 diagnostics 5-1 LEDs 2-6 CLI, installing firmware 4-12 Communications statements 1-2 Community read B-1 trap B-1 Configuration, router 4-10 Connectivity local SAN island 2-6 remote SAN island 2-4 Contact information 1-14 Controls,
S iSR6142 Intelligent Storage Router Installation Guide Firmware installation 4-11 FRU, removing and replacing 6-1 FTP services 3-10 G General public license 1-6 H Hardware, workstation 4-2 Heartbeat LED 2-7 I Installation 4-1 firmware 4-11 site requirements 4-1 transceivers 4-5 Windows 4-7 Internet browser, workstation 4-2 Introduction 1-1 IP address resetting 2-8 workstation 4-6 iSCSI driver messages A-4, A-18 error log messages A-18 fatal log messages A-25 performance 3-3 port LEDs 2-12 iSR6142 rout
A Messages 102419-102748 A-28 1026-1027 A-3 102749-102800 A-29 1028-1061 A-3 1034-1035 A-16 1042-2313 A-16 1056-1072 A-19 106583-107078 A-20 107254-107267 A-21 109 A-3 1111 A-3 1120 A-3 1152-1205 A-28 118882 A-5 119088-119097 A-5 119552-119554 A-5 1-3 A-31 139265-139296 A-22 139297-139553 A-23 151842-151902 A-6 151903-152071 A-7 16-20 A-23 1690-2051 A-3 17-21 A-30 184524-184525 A-8 1-9 A-23 19-23 A-29 200721-200725 A-30 20-24 A-27 204-205 A-8 21-51 A-24 217350 A-9 233473-233475 A-31 237572-237573 A-25 24986
S iSR6142 Intelligent Storage Router Installation Guide MIB Fibre Channel ports B-6 network ports B-4 notifications B-11 objects B-3 sensors B-8 system B-3 Mozilla 4-2 MS Explorer 4-2 N Netscape 4-2 Network ports, MIB B-4 Notification agent shut down B-12 agent start up B-12 FC port down B-12 generic B-13 MIB B-11 network port down B-12 objects B-11 sensor B-13 NTP services 3-10 O Operating system requirements 4-1 workstation 4-1 Ports Fibre Channel 2-9 management 2-12 serial 2-13 POST diagnostics 5-2
A Security, router 3-10 Sensors, MIB B-8 Serial port 2-13 workstation 4-6 Server/ports license 2-3 Services FTP 3-10 NTP 3-10 router 3-10 SNMP 3-10 Telnet 3-10 SFP tranceivers, removing and replacing 6-1 SmartWrite license 2-2 SNMP introduction B-1 properties B-1 services 3-10 trap configuration B-2 Statement CE 1-4 FCC class A 1-3 VCCI class A 1-5 Switch ports 3-8 System contact B-2 error log messages A-25 location B-1 messages A-9 MIB B-3 system fault LEDs 2-7 iSR6142 Intelligent Storage Router Installat
iSR6142 Intelligent Storage Router Installation Guide S Notes Index-6 SN0051102-00 A
