iSR6142 Router Manager User’s Guide SN0054660-00 A
S iSR6142 Router Manager User’s Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
A iSR6142 Router Manager User’s Guide Table of Contents 1 Introduction Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Training . .
iSR6142 Router Manager User’s Guide S FC Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FC Port Information Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FC Port Advanced Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . FC Port Performance Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iSCSI Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A 5 iSR6142 Router Manager User’s Guide Configuring CHAP CHAP Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Discovery Session—Bi-directional CHAP . . . . . . . . . . . . . . . . . . . . . . . . . . Discovery Session—Uni-directional CHAP . . . . . . . . . . . . . . . . . . . . . . . . . Normal Session—Bi-directional CHAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal Session—Uni-directional CHAP . . . . . . . . . . . . . . . . . . . .
S iSR6142 Router Manager User’s Guide Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notification Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agent Start Up Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agent Shut Down Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network Port Down Notification. . . . . . . . . . . . . . . . . . . . . . .
A 3-22 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 4-12 4-13 4-14 4-15 4-16 4-17 4-18 4-19 4-20 4-21 4-22 4-23 4-24 4-25 4-26 4-27 4-28 4-29 4-30 4-31 4-32 4-33 4-34 4-35 4-36 4-37 4-38 4-39 4-40 4-41 4-42 4-43 4-44 iSR6142 Router Manager User’s Guide FCIP Route Statistics Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iSCSI Port Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S iSR6142 Router Manager User’s Guide 4-45 4-46 4-47 4-48 4-49 4-50 4-51 4-52 4-53 4-54 4-55 4-56 4-57 4-58 4-59 4-60 4-61 4-62 4-63 4-64 Refresh Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Mapped Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Device Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Introduction This manual describes the features of the SANsurfer Router Manager used to configure and manage the QLogic iSR6142 Intelligent Storage Router (iSR-6142). For hardware installation, configuration, and diagnostic details, see the iSR6142 Router Installation Guide. Intended Audience This guide is for users who are responsible for installing, managing, and servicing the iSR6142 router and the storage area network (SAN) equipment to which it is attached.
1 – Introduction Technical Support S ANSI SCSI – SCSI-3 Architecture Model (SAM), X3T10/994D/Rev 18, SCSI-3 Controller Command Set, X3T10/Project 1047D/Rev 6c. IEEE – 802.1Q Virtual LAN (VLAN), 802.1p Priority of Service, 802.3x Flow Control, 802.3ad Link Aggregation SCSI-3 Fibre Channel Protocol (SCSI-FCP), X3.269:1996 Fibre Channel Physical and Signaling Interface (FC-PH), X3.230:199 Fibre Channel 2nd Generation (FC-PH-2), X3.
A 1 – Introduction Technical Support Training QLogic offers certification training for the technical professional for QLogic HBAs, CNAs, switches, and routers. From the training link at www.qlogic.com, you may choose Electronic-Based Training or schedule an intensive "hands-on" Certification course. Technical Certification courses include installation, maintenance and troubleshooting QLogic SAN products.
S 1 – Introduction Technical Support Phone Numbers by Language +63-2-885-6712 - English +63-2-885-6713 - (Mandarin) +63-2-885-6714 - (Japanese) +63-2-885-6715 - (Korean) Latin and South America Region 1-4 Email calasupport@qlogic.
2 Using the Graphical User Interface (GUI) The iSR6142 management application is a graphical user interface (GUI) consisting of menus, buttons, and windows that you can use to manage iSR6142s from a workstation on Linux® and Windows® platforms. You can view and change network, port, security, and mapping configuration for one or more iSR6142s. The application displays the most current system information.
S 2 – Using the Graphical User Interface (GUI) Main Window Main Window The SANsurfer Router Manager consists of a menu bar, a tool bar, a system tree, and information/status/data windows and tabs, as illustrated in Figure 2-1 and described in Table 2-1. Figure 2-1 SANsurfer Router Manager Main Window Table 2-1. SANsurfer Router Manager Main Window Sections Item 2-2 Description Menu Bar The menu bar provides access to system functions and wizards.
A 2 – Using the Graphical User Interface (GUI) Menu Bar Table 2-1. SANsurfer Router Manager Main Window Sections (Continued) Item Description System Tree Located on the on the left side of the display, the system tree shows the connected systems and their components. An entry handle located to the left of an entry in the tree shows that you can expand that entry. Click an entry handle or double-click the entry to expand or collapse a system tree entry.
S 2 – Using the Graphical User Interface (GUI) Menu Bar File Menu Figure 2-3 shows the File menu. The following paragraphs describe it. Figure 2-3 File Menu Save FRU – Saves the router’s configuration and persistent data to a file. Restore FRU – Restores the router’s configuration and persistent data from a file. Exit – Exits the SANsurfer Router Manager. View Menu Figure 2-4 shows the View menu. The following paragraph describes it.
A 2 – Using the Graphical User Interface (GUI) Menu Bar Figure 2-6 Broadcast Settings Menu Enable Broadcast – Enables broadcast messages sent to locate routers in the IP subnet. Enable Auto Connect – Enables the SANsurfer Router Manager to automatically connect with routers discovered by the broadcast. Broadcast Interval – Lets you enter the time interval at which the SANsurfer Router Manager sends broadcast messages to locate routers within the same IP subnet as the workstation.
2 – Using the Graphical User Interface (GUI) Menu Bar 2-6 S Map Local Initiator/Target Wizard – Launches the Map Local Wizard, which allows you to map a local initiator to a local target (see page 4-13). Unmap Local Initiator/Target Wizard – Launches the Unmap Local Wizard, which allows you to delete a local initiator from a local target mapping (see page 4-20).
A 2 – Using the Graphical User Interface (GUI) Tool Bar Help Menu Figure 2-8 shows the Help menu. The following paragraphs describe it. Figure 2-8 Help Menu Set Browser Location – Allows you to specify the browser that launches when you view the online help for the SANsurfer Router Manager. Browse Contents – Launches the online help for the SANsurfer Router Manager. About – Displays the application version information. Tool Bar Figure 2-9 shows the tool bar. The following paragraphs describe it.
S 2 – Using the Graphical User Interface (GUI) Action Menu Action Menu The action menu provides short cuts to actions and wizards available elsewhere in the SANsurfer Router Manager. To open this menu, right-click anywhere within the router’s node in the system tree window. Figure 2-10 illustrates the action menu and the following paragraphs describe each available option. Figure 2-10 Action Menu 2-8 Connect – Adds an iSR6142 router to the system tree view.
A 2 – Using the Graphical User Interface (GUI) Action Menu Add Remote Router Wizard – Launches the Add Remote Router Wizard, which allows you to assign local router to a remote router as peers (see page 4-25). Remove Remote Router Wizard – Launches the Remove Remote Router Wizard, which allows you to remove a local-to-remote router peer assignment (see page 4-30).
2 – Using the Graphical User Interface (GUI) System Tree Window S System Tree Window Figure 2-11 shows the system tree window. The following sections described it. Figure 2-11 System Tree Window The left-most window pane shows the system tree.
A 2 – Using the Graphical User Interface (GUI) System Tree Window Figure 2-12 Component Information Component information displayed for a selected router includes router information, configuration details, router status, and lists of connected or discovered devices.
2 – Using the Graphical User Interface (GUI) System Tree Window S Notes 2-12 SN0054660-00 A
3 Managing the Router The SANsurfer Router Manager lets you monitor and manage the iSR6142 router, as well as its ports and connected devices by viewing and selecting components in the system tree.
S 3 – Managing the Router iSR6142 Router Information Tab The Information tab provides four vertical tabs with icons that identify its content: Basic Information, Management Information, and NTP Server Information, and Security. It also contains three buttons: Reboot, FW Load, and Restore Defaults. Basic Information Figure 3-1 Basic Information Vertical Tab The Basic Information tab provides the following parameters: 3-2 Product Name – Identifies the router model.
A 3 – Managing the Router iSR6142 Router Management Information Figure 3-2 Management Information Vertical Tab The Management Information tab provides the following parameters: MAC Address – Displays the management port’s MAC address. Link Status – Displays the management port link status: Link Up or Link Down.
S 3 – Managing the Router iSR6142 Router IPv4 Management Info – Select this check box to use IPv4 (Internet Protocol version 4, 32-bit addressing), then use the radio buttons to identify whether to use a dynamic or static IP address. 3-4 IP Address – Displays the management port’s subnet mask. If you selected the Obtain an IP address automatically (DHCP) radio button, the system obtains the IP address automatically through DHCP.
A 3 – Managing the Router iSR6142 Router IPv6 Default Router – Use this address to set the default router for the IPv6. The system can also set the IPv6 default router dynamically depending on your network configuration. IPv6 Local Link – This field contains the IPv6 link local address of the port. It is not editable. NOTE: IPv6 support is available only with hardware version 6 and software version 2.4.0.0 and greater.
S 3 – Managing the Router iSR6142 Router NTP Server 2 – Displays the IP address of the second NTP server to be queried by the router when setting its time and date. This server is used only if the first NTP server did not respond. NTP Server 3 – Displays the IP address of the third NTP server to be queried by the router when setting its time and date. This server is used only if the first and second NTP servers did not respond.
A 3 – Managing the Router iSR6142 Router SNMP Management Tab The SNMP Management tabbed page consists of two sections: SNMP Configuration and SNMP Trap Receivers. The Save button saves any SNMP management changes. For more information, see Appendix B. Figure 3-5 shows the SNMP Management tabbed page. The following paragraphs describe it.
S 3 – Managing the Router iSR6142 Router Read Community – Enter a password that authorizes an SNMP management server to read information from the router. This is a write-only field. The value on the router and the SNMP management server must be the same. The read community password can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is public. Trap Community – Enter a password that authorizes an SNMP management server to receive traps. This is a write-only field.
A 3 – Managing the Router iSR6142 Router Features Tab Figure 3-6 shows the Features tabbed page that displays the router’s licensed features and lets you apply additional license features. The following paragraphs described the page. Figure 3-6 Features Tabbed Page License Information – Displays a list of the router’s licensed features. Add – Initiates the Add Feature Wizard.
S 3 – Managing the Router iSR6142 Router Topology Tab Figure 3-7 shows the Topology tabbed page that displays the routers, as shown in the following example.
A 3 – Managing the Router FC Ports FC Ports When you select an FC port in the system tree, the system displays the FC Port Information tabbed page (see Figure 3-8). Figure 3-8 FC Port Information Tab FC Port Information Tab The FC Port Information tab provides the following parameters: Node Name – Displays the world-wide node name (WWNN) assigned to the FC port. Port Name – Displays the world-wide port name (WWPN) assigned to the FC port.
3 – Managing the Router FC Ports S Actual Connection Mode – Displays the port’s connection mode, either Point-to-Point or Loop. Actual Data Rate – Displays the port’s operating data rate when online, either one gigabit per second (1 Gbps) or two gigabits per second (2 Gbps). FC Port Advanced Configuration Tab When you select the Advanced Configuration tab for the selected FC port, the system displays the Advanced Configuration tabbed page (see Figure 3-9).
A 3 – Managing the Router FC Ports FC Port Performance Tab When you select the Performance tab for the selected FC port, the system displays the Performance tabbed page (see Figure 3-10). Figure 3-10 FC Port Performance Tab The FC Port Performance tab displays the following information: Initiator Read – Shows the initiator’s read performance through the selected FC port. Initiator Write – Shows the initiator’s write performance through the selected FC port.
S 3 – Managing the Router iSCSI Ports iSCSI Ports When you select an iSCSI port in the system tree, the window displays the Information, Advanced Configuration, and Statistics tabbed pages to the right of the tree (see Figure 3-11). These following sections describe these pages. Figure 3-11 iSCSI Port Tabbed Pages Information Tab The Information tabbed page consists of three areas: Port Information, iSCSI Port Network Settings, and iSNS.
A 3 – Managing the Router iSCSI Ports iSCSI Port Information The iSCSI Port Information area provides the following parameters: Base Name – Displays the full name assigned to the selected iSCSI port. Link Status – Identifies the port connection status: Link Up or Link Down. MAC Address – Displays the MAC address assigned to the port. The MAC address is not changeable. Actual Link Rate – Displays the actual link rate, which can be Unknown, 1000 Mbps, 100 Mbps, or 10 Mbps.
S 3 – Managing the Router iSCSI Ports iSCSI Port Network Settings Port Status – When the port link is up, you can enable or disable the port using this drop-down list. IPv4 Address – When using an IPv4 address scheme, define the following fields: 3-16 IP Address – The IP address to which the port responds. An un-initialized port has an IP address of all zeros. Although you may modify the IP address in this window, you will typically set it using the Configuration Wizard.
A 3 – Managing the Router iSCSI Ports VLAN ID IPv6 – When VLAN IPv6 is enabled the VLAN ID IPv6 contains an identification value in the range 0 to 4094. You can configure VLAN from this window. Priority IPv6 – When VLAN IPv6 is enabled, this field defines the priority assigned to this VLAN IPv6. To set the priority, open the drop-down menu and select the desired value (between 0 to 7). NOTE: IPv6 support is available only with hardware version 6 and greater and software version 2.4.0.
S 3 – Managing the Router iSCSI Ports Advanced Configuration Tab The Advanced Configuration tabbed page allows you to configure the router’s port parameters, security settings, and CHAP settings. The information displayed in these sections is illustrated in Figure 3-12 and described in the following paragraphs. Figure 3-12 Advanced Configuration Tabbed Page The iSCSI Port Advanced Configuration tab provides the following parameters: 3-18 iSCSI Port Number – Identifies the iSCSI port number (1 or 2).
A 3 – Managing the Router iSCSI Ports Target TCP Port Number – Identifies the TCP port number the router uses to receive iSCSI target commands. The iSCSI community uses TCP port number 3260 by default any change to this TCP port number requires a corresponding change in all iSCSI initiators connecting to this iSCSI target port. When you change the target TCP port number, you must click Save (at the bottom of the page) for the change to take effect.
S 3 – Managing the Router iSCSI Ports 3-20 CHAP Settings Enable CHAP – Enables or disables CHAP (Challenge Handshake Authentication Protocol) support. Select the check box to enable this option; clear the check box to disable it. When you change this setting, you must click Save (at the bottom of the page) for the change to take effect. CHAP Secret – Lets you define the CHAP secret used for authenticating an iSCSI client. The field is available only when the Enable CHAP check box is checked.
A 3 – Managing the Router iSCSI Ports Statistics Tab The Statistics tabbed page consists of a scrollable table of parameters and values. The table is divided into two sections: the first section contains statistics that are port specific, and the second section contains shared statistics (common to both iSCSI ports). You can refresh the statistics are by clicking Refresh at the top of the scrollable window. You can clear the statistics (set all values to zero) by clicking Clear.
S 3 – Managing the Router Discovered iSCSI Initiators Discovered iSCSI Initiators Selecting the Discovered iSCSI Initiators branch on the system tree does not provide any information in the right window. Select a discovered iSCSI initiator in the system tree to display the Information and LUN List tabbed pages to the right of the system tree, which are shown in Figure 3-14 and described in the following sections.
A 3 – Managing the Router Discovered iSCSI Initiators The CHAP Settings section provides the following parameters: Enable CHAP – Enables or disables CHAP (Challenge Handshake Authentication Protocol) support. Select the check box to enable this option; clear the check box to disable it. CHAP Secret – Lets you define the CHAP secret used for authenticating an iSCSI client. The field is available only when the CHAP check box is checked.
3 – Managing the Router Discovered iSCSI Initiators S Port – Displays information provided by the target LUN as a result of issuing a SCSI Inquiry command. Protocol – Identifies the target name. For FC targets, the name is the WWPN. WWPN/IQN – Specifies the world-wide unique LUN name (WWULN), also provided on page 83 of a SCSI Inquiry command. WWNN – Shows the logical unit number.
A 3 – Managing the Router FC Discovered Targets Status – Displays information provided by the target LUN in response to the router issuing a SCSI Inquiry command. WWPN – Displays information provided by the target LUN in response to the router issuing a SCSI Inquiry command. Remote IQN – Displays information provided by the target LUN in response to the router issuing a SCSI Inquiry command.
S 3 – Managing the Router FC Discovered Targets Information Tab The Information tabbed page provides the following information about the selected FC target: Product Vendor – Displays the product vendor as reported by the SCSI Inquiry command. Product ID – Displays the product ID as reported by the SCSI Inquiry command. Product Revision – Displays the product revision as reported by the SCSI Inquiry command. Node Name – Displays the world-wide node name of the target device.
A 3 – Managing the Router FC Discovered Targets Node Name – Displays the world-wide node name of the target device. Port Name – Displays the world-wide port name of the target device. Port ID – Displays the target device’s port ID. Target Type – Displays the FC port where the target device was discovered. Target Path – Displays the logical unit number. Target Mode – Displays the vendor name of the LUN as reported by the SCSI Inquiry command.
S 3 – Managing the Router FC Discovered Targets 3-28 Device Product Rev – Displays the product revision of the target device as reported by the SCSI Inquiry command. Device Node Name – Displays the world-wide node name of the target device. Device Port Name – Displays the world-wide port name of the target device. Device Port ID – Displays the target device’s port ID. Presented Port – Displays the iSCSI port number where the target is presented (1 or 2).
A 3 – Managing the Router iSCSI Discovered Targets iSCSI Discovered Targets The iSCSI Discovered Targets branch on the system tree does not provide any information in the right window. Select a discovered target to display the Information tabbed page to the right of the system tree (see Figure 3-20).
S 3 – Managing the Router FCIP Routes iSCSI Name – Displays the presented iSCSI target’s name. Target Path – Displays the router’s iSCSI port where the target was discovered. CHAP Settings – Provides an option you can use to set the challenge handshake authentication protocol (CHAP) option as follows: Enable CHAP – Select this check box to enable CHAP when connecting to this target.
A 3 – Managing the Router FCIP Routes FCIP Route Information Tabbed Page The FCIP Route Information tabbed page contains the information that defines the selected FCIP route, as described in the following paragraphs. FCIP Interface Status – Provides a drop-down box you can use to enable or disable the FCIP route. Disabling the route places the FC and GE ports in a down state, but still retains all route configuration parameters.
3 – Managing the Router FCIP Routes S GigE Link Rate – Provides a drop-down box from which you can choose the link rate of the GigE port from one of four options: Auto, 10 Mbps, 100 Mbps, or 1000 Mbps. Link Rate Mode – When the GigE Link Rate is set to something other than auto, use this drop-down box to choose one of three options for the link rate mode: Auto, Half Duplex, or Full Duplex.
A 3 – Managing the Router FCIP Routes FCIP Route Statistics Tabbed Page The Statistics tabbed page consists of a scrollable table of parameters and values. Figure 3-22 FCIP Route Statistics Page You can refresh the statistics are by clicking Refresh at the top of the scrollable window. You can clear the statistics (set all values to zero) by clicking Clear.
3 – Managing the Router FCIP Routes S Notes 3-34 SN0054660-00 A
4 Using the Wizards The Router Manager provides easy-to-use wizards that walk you through various router configuration procedures.
S 4 – Using the Wizards Configuration Wizard Configuration Wizard The Configuration Wizard provides a set of dialog boxes that walk you through the steps required for configuring the iSCSI ports. This wizard starts automatically when your system connects to a system with any un-configured iSCSI ports. You can also start this wizard at any time by selecting Configuration Wizard from the Wizards Menu or from the Action Menu.
A 4 – Using the Wizards Configuration Wizard Figure 4-2 iSCSI Port Connection Settings Panel Dialog Box 2. To configure the iSCSI Port IPV4 settings: a. b. 3. SN0054660-00 A Type the information in the following fields. IP Address Subnet Mask Gateway If desired, configure the IP address of the iSNS server with which the router registers the selected iSCSI port: Select the Enable iSNS check box to make the Server IP address field editable.
S 4 – Using the Wizards Configuration Wizard Figure 4-3 iSCSI Port IPv6 Settings Panel 4. To configure the iSCSI port IPv6 connection using this dialog box, follow these steps: a. Select Enable IPv6 Address to make the fields editable. b. Specify the iSCSI port IPv6 network settings: c. 5. 4-4 Enter the IPv6 Address 0. Enter the IPv6 Address 1. Enter the IPv6 Default Router. Enter the IPv6 Link Local.
A 4 – Using the Wizards Configuration Wizard Figure 4-4 Confirm Changes Dialog Box 6. SN0054660-00 A Review the configuration changes displayed on the screen, then click Next to confirm your changes.
S 4 – Using the Wizards Configuration Wizard The system displays the iSCSI Port Configuration Status dialog box, as shown in Figure 4-5. Figure 4-5 iSCSI Port Configuration Status 7. Read the information about the status changes, then click Next. The system displays the Refresh dialog box. 8. Read the information. If you would like to see the new configuration, click Yes; otherwise, click No. The system displays the Finish dialog box, as shown in Figure 4-6.
A 4 – Using the Wizards Add Initiator Wizard Figure 4-6 Configuration Wizard Finish Dialog Box 9. Read the information, then click Finish. Add Initiator Wizard The Add Initiator Wizard provides a dialog box used to enter an iSCSI initiator into the system database. iSCSI initiators are normally discovered (their name and address are captured) the first time they log in to the iSR6142 router.
S 4 – Using the Wizards Add Initiator Wizard Figure 4-7 Create an Initiator Dialog Box To create an initiator: 1. Type a name in the Initiator name box. 2. Type an alias in the Initiator alias (iSCSI) box. 3. If you want to enable CHAP for this initiator, select the CHAP Enabled check box. If you want a CHAP secret, type the name in the Initiator’s CHAP Secret box. 4. Click Finish. The Security Check dialog box displays, as shown in Figure 4-8. Figure 4-8 Security Check Dialog Box 5.
A 4 – Using the Wizards FW Update Wizard The new iSCSI initiator is displayed in the discovered iSCSI initiator’s section of the system tree, as shown in Figure 4-9. Figure 4-9 System Tree with New iSCSI Initiator FW Update Wizard The FW Update Wizard provides a set of dialog boxes that walk you through the steps required for updating the iSR6142 firmware. This wizard helps you update the firmware on selected router.
S 4 – Using the Wizards FW Update Wizard To update the firmware, follow these steps: 1. Select the check box next to the routers whose firmware you want to update, then click Next. The Open dialog box displays. Figure 4-11 Firmware File Selection Dialog Box 4-10 2. Enter in the path to the firmware file, or click Browse to locate the firmware file. 3. When the firmware file is displayed in the Firmware Image File field, click Next.
A 4 – Using the Wizards FW Update Wizard The Confirm Changes dialog box displays, as shown in Figure 4-12. Figure 4-12 Confirm Changes Dialog Box 4. Read the information, then do the following: a. If you want to save a copy of this firmware configuration, click Save Configuration to File. Browse to the desired directory, type a file name, then click Save. b. Click Next. The Security Check dialog box requests the Admin password, as shown in Figure 4-13. Figure 4-13 Security Check Dialog Box c.
S 4 – Using the Wizards FW Update Wizard Figure 4-14 Firmware Update Status Dialog Box—Progress When the firmware has loaded successfully, the system displays the Finish dialog box, along with the Update success dialog box, as shown in Figure 4-15.
A 4 – Using the Wizards Map Local Initiator/Target Wizard NOTE: The new firmware will not take effect until the system is rebooted. 6. Complete the wizard: a. If you want to reboot the system now, click Yes. Otherwise, click No. b. Click Finish. Map Local Initiator/Target Wizard The Map Local Initiator/Target Wizard provides a set of dialog boxes that walk you through the steps required for mapping a local initiator to a local target.
S 4 – Using the Wizards Map Local Initiator/Target Wizard The Select a Target dialog box opens, as shown in Figure 4-17. Figure 4-17 Select a Target Dialog Box 2. 4-14 Select a target you want mapped to the previously selected initiator, then click Next.
A 4 – Using the Wizards Map Local Initiator/Target Wizard The wizard screen prompts you to select a port on which the initiator will be presented, as shown in Figure 4-18. Figure 4-18 Select Initiator Port Dialog Box 3. SN0054660-00 A Select the port (FC Port 1 or FC Port 2), then click Next.
S 4 – Using the Wizards Map Local Initiator/Target Wizard The wizard screen prompts you to select a port on which the target will be presents (iSCSI Port 1 and iSCSI Port 2), as shown in Figure 4-19.
A 4 – Using the Wizards Map Local Initiator/Target Wizard The Confirm Changes dialog box displays the local mapping done in the previous steps, as shown in Figure 4-20. Figure 4-20 Confirm Changes Dialog Box 4. SN0054660-00 A Review the information, then click Next.
4 – Using the Wizards Map Local Initiator/Target Wizard S The Security Check dialog box requests the Admin password, as shown in Figure 4-21. Figure 4-21 Security Check Dialog Box 5. 4-18 Type the appropriate password, then click OK to confirm the local mapping.
A 4 – Using the Wizards Map Local Initiator/Target Wizard The Initiator/Target Mapping Configuration Status dialog box displays local mapping completion status, as shown in Figure 4-22. Figure 4-22 Initiator/Target Mapping Configuration Status Dialog Box 6. SN0054660-00 A After reviewing the initiator to target mapping configuration status, click Next.
4 – Using the Wizards Unmap Local Initiator/Target Wizard S After completing the Map Local Initiator/Target Wizard, you can see the mapping by selecting the mapped Initiator in the system tree under Discovered iSCSI Initiators. Click the Local Presented Devices tab, as shown in Figure 4-23. In this example an iSCSI initiator is mapped to an FC target, other mappings are supported such as FC to FC, FC to iSCSI and iSCSI to iSCSI.
A 4 – Using the Wizards Unmap Local Initiator/Target Wizard Figure 4-24 Initiator Selection Dialog Box To unmap a local target from a local initiator: 1. Select the check box next to the initiator you want to unmap, then click Next.
4 – Using the Wizards Unmap Local Initiator/Target Wizard S The Presented Target Selection dialog box displays a list of targets mapped to the initiator selected in the previous step, as shown in Figure 4-25. Figure 4-25 Presented Target Selection Dialog Box 2. 4-22 Select the check box next to the target to unmap, then click Next.
A 4 – Using the Wizards Unmap Local Initiator/Target Wizard The Security Check dialog box requests the Admin password, as shown in Figure 4-26. Figure 4-26 Security Check Dialog Box 3. SN0054660-00 A Type the appropriate password, then click OK to confirm the target is unmapped.
S 4 – Using the Wizards Unmap Local Initiator/Target Wizard The Unpresent Initiator/Target Status dialog box displays the results of the unmap operation, as shown in Figure 4-27. Figure 4-27 Unpresent Initiator/Target Status Dialog Box 4. 4-24 Review the status, then click Next.
A 4 – Using the Wizards Add Remote Router Wizard After completing the UnMap Local Initiator/Target Wizard you can verify the unmapping by selecting the Initiator in the system tree under Discovered iSCSI Initiators. Then select Local Presented Devices. For the example shown in Figure 4-28, an iSCSI initiator was unmapped from an FC target.
4 – Using the Wizards Add Remote Router Wizard S Figure 4-29 Remote Router’s IP Address Dialog Box To add a remoter router to a local router: 1. 4-26 Type the IP Address of the remote router, then click Next.
A 4 – Using the Wizards Add Remote Router Wizard The Status dialog box displays the remote router information along with the Local Router Admin Password dialog box, as shown in Figure 4-30. Figure 4-30 Local Router Admin Password Dialog Box 2. Type the local router admin password (default=config), then click OK. The Status dialog box displays the remote router information, as shown in Figure 4-31.
4 – Using the Wizards Add Remote Router Wizard S 3. Review the status, then click Finish. 4. Click the Refresh icon to refresh the display. 5. Select the router node, then select the Assigned Remote Router:1 tab to display the remote router’s information, as shown in Figure 4-32.
A 4 – Using the Wizards Add Remote Router Wizard 6. Click the Topology tab to display the local and remote router topology including devices attached to both routers, as shown in Figure 4-33.
4 – Using the Wizards Remove Remote Router Wizard S Remove Remote Router Wizard The Remove Remote Router Wizard provides a set of dialog boxes that walk you through the steps required for removing a remote router from the local router. You can start this wizard at any time by selecting Remove Remote Router Wizard from the Wizards Menu or from the Action Menu.
A 4 – Using the Wizards Remove Remote Router Wizard The Local Router Admin Password dialog box requests the local router’s admin password to complete the unmap, as shown in Figure 4-35. Figure 4-35 Local Router Admin Password Dialog Box 2. Type the local router’s admin password (default=config), then click OK. The system prompts you to refresh the display, as shown in Figure 4-36. Figure 4-36 Refresh Screen 3. SN0054660-00 A Click Yes to refresh the display.
S 4 – Using the Wizards Remove Remote Router Wizard The Remove Remote Router Completion dialog box displays the completion status, as shown in Figure 4-37. Figure 4-37 Remove Remote Router Completion Dialog Box 4. 4-32 Click OK to close the message box.
A 4 – Using the Wizards Map Remote Initiator/Target Wizard Map Remote Initiator/Target Wizard The Map Remote Initiator/Target Wizard provides a set of dialog boxes that walk you through the steps required for mapping an initiator to a target, one of which is remote and the other local. You can start this wizard at any time by selecting Map Remote Initiator/Target Wizard from the Wizards Menu or from the Action Menu.
4 – Using the Wizards Map Remote Initiator/Target Wizard S The Device Selection dialog box displays list of devices, as shown in Figure 4-39. Figure 4-39 Device Selection Dialog Box 3. 4-34 If necessary, expand the router tree to see the attached devices. Select the device to be mapped. The device may be a target or an initiator and may be on either the remote router or on the local router. Click Next.
A 4 – Using the Wizards Map Remote Initiator/Target Wizard The port selection dialog box prompts you to select a port the system will use to connect to the device, as shown in Figure 4-40. Figure 4-40 Port Selection Dialog Box 4. Select the port the system will use to connect to the device, then click Next.
4 – Using the Wizards Map Remote Initiator/Target Wizard S The Device Mapping Option dialog box displays SmartWrite mapping options, as shown in Figure 4-41. Figure 4-41 Device Mapping Option Dialog Box 4-36 5. If your router includes the SmartWrite feature, Enable or Disable the options as you want. 6. Click Next.
A 4 – Using the Wizards Map Remote Initiator/Target Wizard The Confirm Mapping dialog box displays the mapping and option selections, as shown in Figure 4-42. Figure 4-42 Confirm Mapping Dialog Box 7. Review the information and, if correct, click Next. The Local Router Admin Password dialog box displays, as shown in Figure 4-43. Figure 4-43 Local Password Dialog Box 8. SN0054660-00 A Type the local router admin password (default=config), then click OK.
S 4 – Using the Wizards Map Remote Initiator/Target Wizard The Remote Mapping Status screen displays a list of newly mapped devices, as shown in Figure 4-44. Figure 4-44 Local Router Admin Password Dialog Box 9. Review the status information, then click Finish. The system prompts you to refresh the display, as shown in Figure 4-45. Figure 4-45 Refresh Screen 10. 4-38 Click Yes to refresh the display.
A 4 – Using the Wizards Map Remote Initiator/Target Wizard 11. View the mapped devices in the router’s tree window. Figure 4-46 shows the mapping created in the sample procedures.
4 – Using the Wizards Unmap Remote Initiator/Target Wizard S Unmap Remote Initiator/Target Wizard The Unmap Remote Initiator/Target Wizard provides a set of dialog boxes that walk you through the steps required for removing an initiator-to-target mapping. You can start this wizard at any time by selecting Unmap Remote Initiator/Target Wizard from the Wizards Menu or from the Action Menu.
A 4 – Using the Wizards Unmap Remote Initiator/Target Wizard The Local Router’s Admin Password dialog box requests the local router’s admin password to continue with the unmap, as shown in Figure 4-48. Figure 4-48 Local Router Admin Password Dialog Box 2. Type the local router’s admin password (default=config), then click OK. The Remote Unmap Initiator-Target Status dialog box displays the status of the unmap operation, as shown in Figure 4-49.
S 4 – Using the Wizards Discover iSCSI Target Wizard Discover iSCSI Target Wizard The Discover iSCSI Target Wizard provides a set of dialog boxes that walk you through the steps required for discovering an iSCSI target. You can start this wizard at any time by selecting Discover iSCSI Target from the Wizards Menu or from the Action Menu.
A 4 – Using the Wizards Discover iSCSI Target Wizard The Security Check dialog box requests the administrator password, as shown in Figure 4-51. Figure 4-51 Discover iSCSI Target Wizard—Security Check Dialog Box 4. Type the appropriate password, then click OK to confirm the discovery of the iSCSI target. If the wizard detected iSCSI targets, the Refresh dialog box signifies the discovery of the iSCSI target, as shown in Figure 4-52. This dialog box may take a few seconds before appearing.
4 – Using the Wizards Discover iSCSI Target Wizard S After the refresh is complete, you can see the Discovered iSCSI Target in the system tree, as shown in Figure 4-53.
A 4 – Using the Wizards FCIP Route Add Wizard FCIP Route Add Wizard The FCIP Route Add Wizard provides a set of dialog boxes that walk you through the steps required for adding an FCIP route. You can start this wizard at any time by selecting FCIP Route Add from the Wizards Menu or from the Action Menu. When the FCIP Route Add Wizard launches, it displays a warning message, letting you know the operation may drop the connection to the selected GE and FC ports.
S 4 – Using the Wizards FCIP Route Add Wizard The FC and GigE Port Selection dialog box prompts you to select an FC-GigE port pair, as shown in Figure 4-55. Figure 4-55 FCIP Route Add Wizard—Port Selection Dialog Box 2. Select the FC-GigE Port pair. The corresponding parameter options become available. 3. If desired, configure the following port route/parameters: 4. 4-46 FCIP Interfaces FC & GE – Provides a drop-down box you can use to enable or disable the FCIP route.
A 4 – Using the Wizards FCIP Route Add Wizard The Local and Remote IP Address dialog box requests entry of IP addresses (see Figure 4-56). Figure 4-56 FCIP Route Add Wizard—Local and Remote IP Address Dialog Box 5. 6. SN0054660-00 A Configure any of the following parameters: Local IP Address – Enter the IP address the GigE port will use. An uninitialized port has an IP address of all zeros. Subnet Mask – Enter the subnet mask the GigE port will use.
S 4 – Using the Wizards FCIP Route Add Wizard The TCP/IP Options dialog box requests entry of TCP/IP parameters, as shown in Figure 4-57. Figure 4-57 FCIP Route Add Wizard—TCP/IP Options Dialog Box 7. Configure any of the following parameters: Jumbo Frames – Provides a drop-down box you can use to enable or disable Jumbo IP frames. When disabled the MTU is 1500 bytes. When enabled the MTU is 9000 bytes.
A 4 – Using the Wizards FCIP Route Add Wizard 8. VLAN ID – Provides a text field you can use to enter the VLAN ID. This option is available only when VLAN is enabled. The VLAN ID must be the same on both routers participating in the FCIP route (that is, local and remote routers must be using same VLAN ID) and the Ethernet switches. VLAN Priority – Provides a drop-down box that contains eight options for the VLAN priority: any number between 0–7.
S 4 – Using the Wizards FCIP Route Add Wizard 10. FCIP SW Compression – Provides a drop-down box you can use to enable or disable FCIP compression. The default is disabled. Bandwidth (Mbit/sec) – Provides a text field in which you can enter the maximum bandwidth (in megabits per second) used by the GigE port during transmits. The range of values supported is 1 to 1000 megabits per second.
A 4 – Using the Wizards FCIP Route Remove Wizard FCIP Route Remove Wizard The FCIP Route Remove Wizard provides a set of dialog boxes that walk you through the steps required for removing an FCIP route. You can start this wizard at any time by selecting FCIP Route Remove from the Wizards Menu or from the Action Menu. When the FCIP Route Remove Wizard launches, it displays a warning message, letting you know the operation may drop the connection to the selected GE and FC ports.
S 4 – Using the Wizards FCIP Route Remove Wizard The FCIP Remove dialog box displays a list of existing FCIP routes, as shown in Figure 4-62. Figure 4-62 FCIP Route Remove Wizard—Route Selection Dialog Box 2. Select the FCIP route you want to remove, then click Finish. The Security Check dialog box requests the administrator password, as shown in Figure 4-63. Figure 4-63 FCIP Route Remove Wizard—Security Check Dialog Box 3.
A 4 – Using the Wizards FCIP Route Remove Wizard The Add FCIP Route Complete dialog box lets you know when the configuration is complete, as shown in Figure 4-64. Figure 4-64 FCIP Route Remove Wizard—Completed Dialog Box NOTE: This dialog box may take a few seconds before appearing. 4. SN0054660-00 A Click OK to exit the dialog box.
4 – Using the Wizards FCIP Route Remove Wizard S Notes 4-54 SN0054660-00 A
5 Configuring CHAP This chapter describes CHAP and provides the procedures for configuring CHAP using the SANsurfer Router Manager.
S 5 – Configuring CHAP Discovery Session—Bi-directional CHAP Discovery Session—Bi-directional CHAP To configure a bi-directional CHAP during a discovery session: 5-2 1. On the bridge, enable CHAP for the iSCSI port. 2. Select the port in the left column. 3. Click Advanced Configuration. 4. Select Enable Chap. 5. Type a secret in Chap secret (for example, secret_port). 6.
A 5 – Configuring CHAP Discovery Session—Uni-directional CHAP Discovery Session—Uni-directional CHAP To program a single-direction CHAP during a discovery session: 1. Do not enable CHAP on the iSCSI port. 2. Check to see if the initiator exists on the discovered iSCSI initiators list: If the initiator is not part of the discovered iSCSI initiators list, then go to the wizard menu and select Add Initiator Wizard. If the initiator is part of the discovered list, then go to Step 6. 3.
S 5 – Configuring CHAP Normal Session—Uni-directional CHAP 6. Check to see if the initiator exists on the discovered iSCSI initiators list: If the initiator is not part of the discovered iSCSI initiators list, then go to the wizard menu and select Add Initiator Wizard. If the initiator is part of the discovered list, then go to Step 10. 7. Fill in the IQN name string. 8. Select Enable Chap. 9. Create a CHAP secret (for example, secret_initiator). 10.
A 5 – Configuring CHAP Normal Session—Uni-directional CHAP 5. Create a CHAP secret (for example, secret_initiator). 6. Go to the MS Initiator and perform the following steps: 7. SN0054660-00 A a. Click Targets. b. Select the target you want to login to. c. Click Log On. d. Click Advanced. e. Click Chap Login Information. f. Type the secret (secret_initiator) you created in Step 5 into Target Secret, g. Click OK. Click OK. The initiator completes normal login.
5 – Configuring CHAP Normal Session—Uni-directional CHAP S Notes 5-6 SN0054660-00 A
A Log Messages This appendix provides reference material on messages logged to a file. You can view these message logs from the SANsurfer Router Manager using any of these methods: Select View Logs from the View menu. Click the View Logs tool bar icon. Right-click anywhere within the router’s node in the system tree window and select View Logs from the action menu. Log Data The message log is persistent, maintained across router power cycles and reboots.
S A – Log Messages Informational Log Messages Application Modules The application modules generate the informational log messages listed in Table A-1 and described following the table. Table A-1. Application Modules—Informational Log Messages ID A-2 Log Message No. 53254 System (router) Booting up 6 53357 QLBA_ProcessTpb: De-compression failed. Disabling compression temporarily 109 54274 QLFC_Login: Origin 0x%x, VP Index 0x%x, Id 0x%x 1026 54275 QLFC_Login: Port ID %.2x%.2x%.
A A – Log Messages Informational Log Messages Table A-1. Application Modules—Informational Log Messages (Continued) ID Log Message No. 54963 QLIS_SetDdbEntryContinue:[%d:%d] Remote system connection established 1715 54986 QLIS_HandleSessionTimer: Re-enabling compression 1738 55299 QLSC_CollectBUVUIO: Freeing dead TRB: State 0x%02X, AbortReason %d, Flags 0x%02X 2051 6 Router is booting up. 109 De-compression failed and will be temporarily disabled.
S A – Log Messages Informational Log Messages 1700 iSCSI connection closed. 1715 Remote system connection established using DDB d:d. 1738 Re-enabling compression. 2051 TRB freed, State xx, Abort Reason d, Flags xx. iSCSI Driver The following informational log messages are common to both iSCSI ports: 1 (GE1) and 2 (GE2). The messages are listed in Table A-2 and described following the table.
A A – Log Messages Informational Log Messages Fibre Channel Driver The following informational log messages are common to both Fibre Channel ports: 1 (FC1) and 2 (FC2). The messages are listed in Table A-3 and described following the table. Log messages beginning with #0 denote Fibre Channel port 1 (FC1). Log messages beginning with #1 denote Fibre Channel port 2 (FC2). Table A-3. Fibre Channel Driver—Informational Log Messages ID Log Message No.
S A – Log Messages Informational Log Messages 768 FCIP - Fibre Channel link up occurred. Event status is reported, as is the contents of the FC processor’s mailbox 1 register. 769 FCIP - Fibre Channel link down occurred. 770 FCIP - Fibre Channel link up occurred. Event status is reported, as is the RunTimeMode (0 = loop, 1 = point-to-point). User Modules The user modules generate the log messages listed in Table A-4 and described in the following table. Table A-4.
A A – Log Messages Informational Log Messages Table A-4. User Modules—Informational Log Messages (Continued) ID Log Message No. 151903 qapimaptargettoinitiator_1_svc: Localmap added to target device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x 351 151904 qapiunmaptargettoinitiator_1_svc: Localmap removed for initiator device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x 352 151905 qapiunmaptargettoinitiator_1_svc: Localmap removed to target device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.
S A – Log Messages Informational Log Messages 348 Remotemap removed for local FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx. 349 Remotemap removed for remote FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx. 350 Localmap added for FC initiator WWPN xx.xx.xx.xx.xx.xx.xx.xx. 351 Localmap added to FC target device WWPN xx.xx.xx.xx.xx.xx.xx.xx. 352 Localmap removed for FC initiator. 353 Localmap removed to FC target device. 354 Localmap added for iSCSI initiator "iqn.dddd-dd.ttt.ttt.ttt.......".
A A – Log Messages Informational Log Messages TOE Driver The TOE driver generates the informational log messages listed in Table A-6 and described following the table. Table A-6. TOE—Informational Log Messages ID 217350 262 Log Message QL3022:eth%x: Interface is down No. 262 The GigE interface d (0 or 1) used for an FCIP route is down. System The system modules generate the informational log messages listed in Table A-7 and described following the table. Table A-7.
S A – Log Messages Error Log Messages Error Log Messages The following sections list and describe the error log messages by reporting module: “Application Modules” on page A-10 “iSCSI Driver” on page A-18 “Fibre Channel Driver” on page A-20 “User Modules” on page A-22 “System” on page A-25 Application Modules The application modules generate the error log messages listed in Table A-8 and described following the table. Table A-8.
A A – Log Messages Error Log Messages Table A-8. Application Module—Error Log Messages (Continued) ID SN0054660-00 A Log Message No. 41257 QLIS_LoginPduContinue: Invalid initiator name. Initiator: 297 41265 QLIS_LoginPduContinue: Target not configured for Portal 305 41267 QLIS_LoginPduContinue: Target not found.
S A – Log Messages Error Log Messages Table A-8. Application Module—Error Log Messages (Continued) ID A-12 Log Message No. 41771 QLBI_GetLunList: Lun allocation failed for LunId %d 811 41994 QLFC_Login: VpIndex (%d) out of range 1034 41995 QLFC_Login: VP Index 0x%x not configured 1035 42002 QLFC_Login: Can't open connection 1042 42024 QLFC_Logout: No active path to device. WWPN: %.2X%.2X%.2X%.2X%.2X%.2X%.2X%.
A A – Log Messages Error Log Messages Table A-8. Application Module—Error Log Messages (Continued) ID SN0054660-00 A Log Message No.
S A – Log Messages Error Log Messages A-14 7 NULL doorbell routine for unloaded drivers. When a driver is unloaded, the doorbell routine is redirected to this NULL routine. 36 Processing unsupported ordered tag task management command. 44 Processing unsupported head-of-queue task management command. 98 Unable to create an object for the target device: exceeded the maximum number of target devices. 100 Unable to create an object for the target node: exceeded the maximum number of target devices.
A A – Log Messages Error Log Messages 323 iSCSI Login PDU was received with a TSIH out of range. This would occur if the iSCSI initiator attempting the login failed to used the TSIH value provided in the Target Login Response PDU (router is target) in subsequent login PDUs. 324 iSCSI Login PDU was received with an invalid TSIH value. The TSIH is invalid because there is no session with that TSIH value.
S A – Log Messages Error Log Messages A-16 1034 Login attempted using Fibre Channel virtual port (VP) index that is out-of-range (range = 0–31). Index reported in log message. 1035 Login attempted using Fibre Channel VP index that has not been configured. Operation attempted on an unconfigured VP. 1042 Attempting login but Fibre Channel connection cannot be opened. 1064 Attempting logout of device for which there is no active path (WWPN not found).
A A – Log Messages Error Log Messages 2311 FCIP incoming frame: Got Status aborted pTrb->pBufDescList[0]:%p Trb Direction:0x%x. 2312 FCIP system error. 2313 FCIP system error: QLOP_IssuePortEnable failed. 2320 FCIP handle Teb: Driver Fatal error. 2321 FCIP configure portal: Find portal object failed for QLUT_TYPE_FC, PortId (%d). 2322 FCIP configure portal: QLFCIP_ConfigPortal: Invalid PortId for FCIP link PortID(%d). 2323 FCIP allocate TRB pool: Allocation failed (size 0x%x).
S A – Log Messages Error Log Messages iSCSI Driver The following error log messages are common to both iSCSI ports, 1 (GE1) and 2 (GE2). They are listed in Table A-9 and described following the table. Log messages beginning with #0 denote iSCSI port 1 (GE1). Log messages beginning with #1 denote iSCSI port 2 (GE2). Table A-9. iSCSI Driver—Error Log Messages ID A-18 Log Message No.
A A – Log Messages Error Log Messages 329 The iSCSI processor failed the external loopback test. 337 The iSCSI processor command to disable a GE port failed. 513 The iSCSI processor could not connect with the iSCSI name server (iSNS). 849 The iSCSI processor reported that the iSCSI port NVRAM contains invalid data (checksum error). 859 The iSCSI processor reported a link down condition. 928 The driver failed to receive a heartbeat from the iSCSI processor for the specified number of seconds.
S A – Log Messages Error Log Messages Fibre Channel Driver The following error log messages are common to both Fibre Channel ports, 1 (FC1) and 2 (FC2). They are listed in Table A-10 and described in this section. Log messages beginning with #0 denote Fibre Channel port 1 (FC1) and log messages beginning with #1 denote Fibre Channel port 2 (FC2). Table A-10. Fibre Channel Driver—Error Log Messages A-20 ID Log Messages No.
A A – Log Messages Error Log Messages Table A-10. Fibre Channel Driver—Error Log Messages (Continued) ID Log Messages No. 107254 #%d: QLUpdateSinglePortCont 0x%x: out of slots in host database 758 107267 #%d: QLFcipIsrEventHandler: System error event (%x), MB1=%x, MB2=%x, MB3=%x, MB4=%x, MB5=%x, MB6=%x, MB7=%x 771 87 The FC processor received a SCSI command for an unknown target path or has run out of resources to execute additional commands.
S A – Log Messages Error Log Messages 582 The drivers host (initiator) database is full. 758 No slots available in host database. 771 FCIP system error event. User Modules The user modules generate the error log messages listed in Table A-11 and described following the table. Table A-11. User Modules—Error Log Messages ID A-22 Log Message No.
A A – Log Messages Error Log Messages Table A-11. User Modules—Error Log Messages (Continued) ID Log Message No.
S A – Log Messages Error Log Messages A-24 21 Failed memory allocation for Get LUN List API. 22 Failed memory allocation for Get Presented Targets List API. 23 Failed memory allocation for Get LUN Mask API. 24 Failed memory allocation for Initiator API. 25 Failed memory allocation for Target Device API. 32 Failed memory allocation for FC Target API. 33 Failed memory allocation for System Status API. 34 Failed memory allocation for Diagnostic API.
A A – Log Messages Fatal Log Messages System The system modules generate the error log messages listed in Table A-12 and described following the table. Table A-12. System—Error Log Messages ID Log Message No. 237572 "Failed to kill sys killer %d\n" 4 237573 "Temperature over high threshold %d\n" 5 4 Failed to kill system task. 5 Reporting router exceeds maximum operating temperature.
S A – Log Messages Fatal Log Messages Table A-13. iSCSI Driver—Fatal Log Messages (Continued) ID A-26 Log Message No.
A A – Log Messages Fatal Log Messages Table A-13. iSCSI Driver—Fatal Log Messages (Continued) ID Log Message No. 70836 #%d: QLStartFw: Invalid Fw loader state 0x%x 1204 70837 #%d: QLStartFw: Load Fw loader timeout 1205 20 iSCSI processor SRAM test failed. 21 iSCSI processor failed diagnostic reboot. 22 iSCSI processor failed NVRAM diagnostic. 23 iSCSI processor failed DRAM diagnostic. 24 iSCSI processor failed to return diagnostic results.
S A – Log Messages Fatal Log Messages 978 iSCSI processor reboot failed. 1152 iSCSI processor NVRAM invalid (checksum error). 1203 iSCSI FLASH (NVRAM) command failed. 1204 iSCSI firmware loader invalid state. 1205 iSCSI failed to load firmware in time allotted. FC Driver The following fatal log messages are common to both Fibre Channel ports, 1 (FC1) and 2 (FC2). They are listed in Table A-14 and described following the table. Log messages beginning with #0 denote Fibre Channel port 1 (FC1).
A A – Log Messages Fatal Log Messages Table A-14. Fibre Channel Driver—Fatal Log Messages (Continued) ID Log Message No.
S A – Log Messages Fatal Log Messages 292 FC processor paused due to RAM parity error. 316 FC processor system error. 346 Response queue entry contains an invalid handle. 347 FCIP: Response queue entry contains an invalid buffer type. 348 FCIP: Response queue entry contains an invalid entry type. 349 FCIP: Response queue entry contains an invalid handle. 352 FC processor external SRAM parity error count exceeded limit: FC port disabled. 355 FC processor heartbeat failed.
A A – Log Messages Fatal Log Messages System The system modules generate the fatal log messages listed in Table A-16 and described following the table. Table A-16. System—Fatal Log Messages ID Log Message No. 233473 "memory monitor: Detected Uncorrectable Ecc %08lx system is rebooting in 5 secs\n" 1 233474 "Failed to register interrupt handler!\n" 2 233475 "%s class_simple_create failed\n" 3 1 Uncorrectable memory error detected at address provided in log message.
A – Log Messages Fatal Log Messages S Notes A-32 SN0054660-00 A
B Simple Network Management Protocol (SNMP) Introduction Simple network management protocol (SNMP) provides monitoring and trap functions for managing the router through third-party applications that support SNMP. The router firmware supports SNMP versions 1 and 2 and a QLogic (see page B-3). You may format the traps using SNMP version 1 or 2 (see page B-11). SNMP Properties You can set the SNMP properties using the SANsurfer Router Manager (see “SNMP Management Tab” on page 3-7).
S B – Simple Network Management Protocol (SNMP) Introduction Table B-1. SNMP Properties (Continued) Parameter Description System contact Specifies the name of the person to be contacted to respond to trap events. The name can be up to 64 characters excluding the number sign (#), semicolon (;), and comma (,). The default is undefined. Authentication traps Enables or disables authentication trap generation in response to authentication failures. The default is disabled.
A B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) Management Information Base (MIB) The following sections describe the QLogic management information base (MIB). The MIB consists of four object groups: System Information Network Port Table Fibre Channel Port Table Fibre Channel Port Table System Information The system information objects provide the system serial number, version numbers (hardware/software/agent), and number of ports (FC/GE).
S B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrNoOfGbEPorts Syntax Unsigned32 Access Read-only Description The number of gigabit Ethernet ports on the system. qsrAgentVersion Syntax SnmpAdminString Access Read only Description The version number of the agent software on the system. Network Port Table The network port table contains a list of network ports that are operational on the router.
A B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrNetMask InetAddress qsrGateway InetAddress qsrMacAddress MacAddress qsrNwLinkStatus QsrLinkStatus qsrNwLinkRate QsrLinkRate qsrNwPortRole Syntax QsrPortRole Access Not accessible Description The operational role of this port: management port, iSCSI port, a TOE. qsrNwPortIndex Syntax Unsigned32 Access Not accessible Description A positive integer indexing each network port in a given role.
B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) S qsrNetMask Syntax InetAddress Access Read only Description The subnet mask for this port. qsrGateway Syntax InetAddress Access Read only Description The gateway for this port. qsrMacAddress Syntax IMacAddress Access Read only Description The MAC address for this port. qstNwLinkStatus Syntax QsrLinkStatus Access Read only Description The operational link status for this port.
A B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrFcPortEntry Syntax QsrFcPortEntry Access Not accessible Description Each entry (row) contains information about a specific FC port.
B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) S qsrFcPortWwn Syntax PhysAddress Access Read only Description The world-wide name for this port. qsrFcPortId Syntax PhysAddress Access Read only Description The interface's 24-bit FC address identifier. qsrFcPortType Syntax Unsigned32 Access Read only Description The type of FC port, as indicated by the use of the appropriate value assigned by IANA. The IANA-maintained registry for FC port types can be found at: www.iana.
A B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrSensorEntry Syntax QsrSensorEntry Access Not accessible Description Each entry (row) corresponds to a single sensor.
B – Simple Network Management Protocol (SNMP) Management Information Base (MIB) S qsrSensorValue Syntax Integer32 Access Read only Description The current value of the sensor. qsrUpperThreshold Syntax Integer32 Access Read only Description The upper-level threshold for this sensor. qsrLowerThreshold Syntax Integer32 Access Read only Description The lower-level threshold for this sensor.
A B – Simple Network Management Protocol (SNMP) Notifications Notifications The router provides the following notification types: Notification Objects Agent Start Up Notification Agent Shut Down Notification Network Port Down Notification Fibre Channel Port Down Notification Sensor Notification Generic Notification The following sections describe these notifications and objects they use. Notification Objects This section defines the objects used in notifications.
B – Simple Network Management Protocol (SNMP) Notifications S Agent Start Up Notification The agent startup notification indicates that the agent on the router has started running. qsrAgentStartup uses the following object: qsrEventTimeStamp Agent Shut Down Notification The agent shut down notification indicates that the agent on the router is shutting down.
A B – Simple Network Management Protocol (SNMP) Notifications Sensor Notification The sensor notification indicates that the state for the specified sensor is not normal. When the sensor returns to the normal state, this event is sent with the qsrEventSeverity object set to clear. qsrSensorNotification uses the following objects: qsrSensorValue qsrSensorState qsrEventTimeStamp qsrEventSeverity Generic Notification The generic notification reports events other than the defined event types.
B – Simple Network Management Protocol (SNMP) Notifications S Notes B-14 SN0054660-00 A
Index A Action menu 2-3, 2-8 Add Initiator Wizard 2-5 menu option 2-9 procedures 4-7 Add Remote Router Wizard 2-6 menu option 2-9 procedures 4-25 Advanced configuration FC port 3-12 iSCSI ports 3-18 Application error log A-10 log messages A-2 B Bandwidth, FCIP routes 3-32 Base name, iSCSI ports 3-15 Beacon OFF 2-9 ON 2-9 Bi-directional CHAP configuration 5-2, 5-3 Broadcast 2-4 enabling 2-5 interval 2-5 Browser location 2-7 Burst length, iSCSI ports 3-19 C CHAP configuration 5-1 iSCSI port settings 3-20 S
S iSR6142 Router Manager User’s Guide F Fatal log messages A-25 FC discovered targets 3-25 driver fatal log messages A-28 link status, FCIP routes 3-31 port advanced configuration 3-12 port, FCIP routes 3-31 port, MIB B-6 ports 3-11 FCIP messages A-8 routes, interface status 3-31 FCIP Route Add Wizard 2-6 menu option 2-9 procedures 4-45 FCIP Route Remove Wizard 2-6 menu option 2-9 procedures 4-51 Features, licensed 3-9 Fibre Channel driver messages A-5 error log messages A-20 port count 3-2 ports 3-11 Fil
A J Jumbo frames FCIP routes 3-31 iSCSI ports 3-19 L iSR6142 Router Manager User’s Guide Menus Action 2-8 File 2-4 Help 2-7 Settings 2-4 View 2-4 Wizards 2-5 License, features tab 3-9 Link rate GigE 3-32 iSCSI ports 3-15 mode 3-15 mode, FCIP routes 3-32 Link status FC port 3-11 GigE 3-31 iSCSI ports 3-15 management port 3-3 Local IP address, FCIP routes 3-31 presented target 3-23 Log data A-1 messages A-1 Logs, viewing 2-4 M MAC address iSCSI ports 3-15 management port 3-3 Main window 2-2 Management IP
S iSR6142 Router Manager User’s Guide Messages 102419-102748 A-28 1026-1027 A-3 102749-102800 A-29 1028-1061 A-3 1034-1035 A-16 1042-2313 A-16 1056-1072 A-19 106583-107078 A-20 107254-107267 A-21 109 A-3 1111 A-3 1120 A-3 1152-1205 A-28 118882 A-5 119088-119097 A-5 119552-119554 A-5 1-3 A-31 139265-139296 A-22 139297-139553 A-23 151842-151902 A-6 151903-152071 A-7 16-20 A-23 1690-2051 A-3 17-21 A-30 184524-184525 A-8 1-9 A-23 19-23 A-29 200721-200725 A-30 20-24 A-27 204-205 A-8 21-51 A-24 217350 A-9 23347
A MIB Fibre Channel ports B-6 network ports B-4 notifications B-11 objects B-3 sensors B-8 system B-3 N Network ports, MIB B-4 settings, iSCSI ports 3-16 Node name, FC port 3-11 Notification agent shut down B-12 agent start up B-12 FC port down B-12 generic B-13 MIB B-11 network port down B-12 objects B-11 sensor B-13 NTP, server information 3-5 Number, iSCSI ports 3-18 P Password 3-6 Performance, FC port 3-13 Ping, menu option 2-8 Port count, iSCSI 3-9 FC 3-11 ID, FC port 3-11 name, FC port 3-11 Presente
S iSR6142 Router Manager User’s Guide Save FRU 2-4 Security iSCSI port settings 3-19 router 3-6 Sensors, MIB B-8 Serial number remote router 3-9 router 3-2 Settings menu 2-4 SNMP configuration 3-7 introduction B-1 management 3-7 properties B-1 trap configuration B-2 trap receivers 3-8 Software version remote router 3-9 router 3-2 Statistics FCIP routes 3-33 iSCSI ports 3-21 Status 2-3 FC ports 3-11 iSCSI ports 3-16 Subnet mask, FCIP routes 3-31 Symbolic name remote router 3-9 router 3-2 System contact B-2
A iSR6142 Router Manager User’s Guide View logs icon 2-7 menu option 2-8 View menu 2-4 VLAN, FCIP routes 3-32 W Window scaling, FCIP routes 3-31 Windows, system tree 2-10 Wizards Add Initiator, launching 2-5 Add Initiator, using 4-7 Add Remote Router, launching 2-6 Add Remote Router, using 4-25 Configuration, launching 2-5 Configuration, using 4-2 Discover iSCSI Target, launching 2-6 Discover iSCSI Target, using 4-42 FCIP Route Add, launching 2-6 FCIP Route Add, using 4-45 FCIP Route Remove, launching 2-
iSR6142 Router Manager User’s Guide S Notes Index-8 SN0054660-00 A
