iSR6152 Router Manager User’s Guide ISR645610-00 B
iSR6152 Router Manager User’s Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
Table of Contents Preface Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What’s in this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What’s in the Help System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Documentation Conventions . . . . . . . . . . . . . . . . . . .
iSR6152 Router Manager User’s Guide 2 Understanding the User Interface Main Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . File Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . View Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Settings Menu .
iSR6152 Router Manager User’s Guide FC Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Advanced Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Performance . . . . . . . . . . . . . . . . . . . . . . . . .
iSR6152 Router Manager User’s Guide Data Migration Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Data Migration Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Synchronizing Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Completed Data Migration Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A Simple Network Management Protocol (SNMP) Introduction. . . . . . . . . . . . . . . . .
iSR6152 Router Manager User’s Guide List of Figures Figure Page 1-1 Connect to Router Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 1-2 Browser Location Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 1-3 About SANsurfer Router Manager Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 1-4 Setting System Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSR6152 Router Manager User’s Guide List of Tables Table 1-1 2-1 2-2 2-3 3-1 A-1 A-2 B-1 viii System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interface Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Toolbar Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shortcut Menu Options . . . . . . . . . . . . . . . . . . . . .
Preface This user’s guide describes the features of SANsurfer Router Manager used to configure and manage the QLogic iSR6152 Intelligent Storage Router (iSR6152). The iSR6152 management utility is a GUI consisting of menus, buttons, and options that you can use to manage iSR6152s from a workstation on Linux® and Windows® platforms. You can view and change network, port, security, and mapping configuration for one or more iSR6152s. The utility shows the most current system information.
Preface What’s in the Help System Chapter 4 Viewing Service Information describes the pages used to monitor and manage the licensed services—including data migration—by viewing and selecting components in the services tree. Appendix A Simple Network Management Protocol (SNMP) provides reference material for the SNMP, which you can use to manage the iSR6152 router using a third-party SNMP management utility.
Preface Documentation Conventions Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification, RFC2463 Transmission of IPv6 Packets over Ethernet Networks, RFC2464 iSCSI draft standard draft-ietf-ips-iSCSI-20 Internet engineering task force (IETF) – iSCSI Requirements and Design Considerations, iSCSI Naming and Discovery, Internet Protocol Specification (IPv4), RFC793 Transmission Control Protocol (TCP) Specification, RFC1122, Requirements for Internet
Preface Documentation Conventions xii Text in blue font indicates a hyperlink (jump) to a figure, table, or section in this guide, and links to Web sites are shown in underlined blue. For example: Table 9-2 lists problems related to the user interface and remote agent. See “Installation Checklist” on page 3-6. For more information, visit www.qlogic.com. Text in bold font indicates user interface elements such as menu items, buttons, check boxes, or column headings.
Preface License Agreements Figure i. Example: Jagged Edges Depict Partial Interface License Agreements Refer to the QLogic Software End User License Agreement for a complete listing of all license agreements affecting this product. Technical Support Customers should contact their authorized maintenance provider for technical support of their QLogic switch products. QLogic-direct customers may contact QLogic Technical Support; others will be redirected to their authorized maintenance provider.
Preface Technical Support Contact Information QLogic Technical Support for products under warranty is available during local standard working hours excluding QLogic Observed Holidays. For customers with extended service, consult your plan for available hours. For Support phone numbers, see the Contact Support link at http://support.qlogic.com. Support Headquarters QLogic Corporation 4601 Dean Lakes Blvd. Shakopee, MN 55379 USA QLogic Web Site www.qlogic.com Technical Support Web Site http://support.
1 Getting Started This chapter provides information to help you get started using SANsurfer Router Manager.
1–Getting Started Connecting the Management Workstation to the Router Table 1-1.
1–Getting Started Connecting the Management Workstation to the Router For a Windows workstation: 1. On the Windows Start menu, point to Settings, point to Control Panel, and then click Network and Dial-up Connections. 2. Click Make New Connection. 3. Click Connect to a private network through the Internet, and then click Next. 4. Type the new IP address; for example, 10.0.0.253. For a Linux or Solaris workstation: 1. Open a command window. 2.
1–Getting Started Starting SANsurfer Router Manager 3. Launch the FW Update Wizard using one of the following methods: On the File menu, click FW Update Wizard. Press CTRL+F. 4. On the FW Update Wizard dialog box under Router Selection, select the check box corresponding to the router (specified by IP address) to update, and then click Next. 5. Complete the Firmware File Selection section as follows: 6. 7. a.
1–Getting Started Starting SANsurfer Router Manager Starting SANsurfer Router Manager on Windows On a Windows system, do one of the following to start the SANsurfer tool, which includes the SANsurfer Router Manager user interface.
1–Getting Started Connecting SANsurfer Router Manager to the Router The SANsurfer Router Manager main window opens (see “Main Window” on page 2-2). Connecting SANsurfer Router Manager to the Router Follow the steps in this section to connect SANsurfer Router Manager to the iSR6152 router. To connect SANsurfer Router Manager to the iSR6152: 1. 2.
1–Getting Started Getting Help Getting Help This section provides information about: “Viewing the Help System” on page 1-7 “Specifying the Help Browser” on page 1-8 “Viewing SANsurfer Router Manager Information” on page 1-9 Viewing the Help System You can view the application help for SANsurfer Router Manager at any time using one of the following methods: ISR645610-00 B To view the help system from the main window, point to the Help menu, and then click Browse Contents.
1–Getting Started Getting Help NOTE: The search tool accepts Boolean expressions (such as AND, OR, and NOT), as well as nested expressions. It also accepts exact strings entered between quotation marks. It does not support wild cards. To view help related to a specific wizard dialog box or window, click the Help button, located at the lower-right corner of the dialog box. The appropriate topic opens in a separate window.
1–Getting Started Getting Help 3. When you finish choosing your browser, do one of the following: To save the browser location to the SANsurfer Router Manager configuration file, click OK. To close the Browser Location dialog box without making changes, click Cancel. Viewing SANsurfer Router Manager Information The About box shows the product version number and QLogic copyright information. To view information about SANsurfer Router Manager: 1.
1–Getting Started Setting Security Setting Security SANsurfer Router Manager security ensures that any router configuration changes require password authorization.
1–Getting Started Setting Security Figure 1-4. Setting System Security 4. Under Application Access, complete the following boxes: Current Password: Type the existing login password. NOTE: The default password is config. New Password: Type the new password. Verify New Password: Type the new password again to confirm the new password. NOTE: If necessary, click Clear Fields to clear the typed entries in the Security page text boxes. 5. To update the access password, click Apply.
1–Getting Started Refreshing the Host Configuration Refreshing the Host Configuration The host configuration (including the router tree) shown in the SANsurfer Router Manager interface does not automatically update all configuration changes. To update the interface to view all configuration changes, either made by yourself or another user, choose one of the following options: On the toolbar, click the Refresh button: Right-click the router tree, and then on the shortcut menu, click Refresh.
1–Getting Started Exiting SANsurfer Router Manager Exiting SANsurfer Router Manager To exit SANsurfer Router Manager, choose one of the following options: On the SANsurfer Router Manager main window, open the File menu, and then click Exit. On the SANsurfer Router Manager main window, click the Close button in the upper right corner. Press the ALT+X keys.
1–Getting Started Exiting SANsurfer Router Manager 1-14 ISR645610-00 B
2 Understanding the User Interface This chapter describes the components of the SANsurfer Router Manager user interface, including the: “Main Window” on page 2-2 “Menu Bar” on page 2-3 “Toolbar” on page 2-6 “Shortcut Menus” on page 2-6 “Tree Pane” on page 2-10 “Status Icons and Text” on page 2-13 ISR645610-00 B 2-1
2–Understanding the User Interface Main Window Main Window The SANsurfer Router Manager interface consists of a menu bar, a toolbar, a status bar, a tree pane, and an information/configuration/data pane with tabbed pages, as illustrated in Figure 2-1 and described in Table 2-1. Menu Bar Status Bar Tree Pane Toolbar Shortcut Menu Tabs Information, Configuration, and Data Pane Figure 2-1.
2–Understanding the User Interface Menu Bar Table 2-1. Interface Description Item Description Menu Bar The menu bar provides access to system functions and wizards. For details, see “Menu Bar” on page 2-3. Toolbar The toolbar buttons provide quick access to common functions: Connect, View Logs, and Refresh. For details, see “Toolbar” on page 2-6.
2–Understanding the User Interface Menu Bar Restore FRU recovers the router’s configuration and persistent data from a file. (For details, see “Restoring the FRU” in the help system.) Import Host-LUN Info loads the XML output from the host tool utility containing host volume information. Save Capture saves logs and configuration information for Technical Support. Exit closes SANsurfer Router Manager.
2–Understanding the User Interface Menu Bar Configure Migration Jobs opens the Create Data Migration Job dialog box to schedule an individual data migration job or multiple jobs to run in batch mode. (Data migration is an optional, licensed feature of SANsurfer Router Manager.) Configure Verifying Jobs launches the Verify Migration Job wizard to configure verification jobs to compare data residing on two LUNs. (Data migration is an optional, licensed feature of SANsurfer Router Manager.
2–Understanding the User Interface Toolbar NOTE: Detailed procedures for the wizards are included in the “Using the Wizards” section of the help system. Help Menu The Help menu provides the following options: Set Browser Location specifies the browser that launches when you view the help system for SANsurfer Router Manager. For procedures, see “Specifying the Help Browser” on page 1-8. Browse Contents launches the help system for SANsurfer Router Manager.
2–Understanding the User Interface Shortcut Menus NOTE: The options that are available on the shortcut menus depend on the router to which SANsurfer Router Manager is connected and the features licensed for the connected router. Router Shortcut Menu Services Shortcut Menu Figure 2-2.
2–Understanding the User Interface Shortcut Menus Table 2-3 provides a description of each shortcut menu option, listed alphabetically. NOTE: Data migration is an optional, licensed feature of SANsurfer Router Manager. Detailed procedures for the wizards are included in the “Using the Wizards” section of the help system. Table 2-3. Shortcut Menu Options Option Description Add Group Opens a dialog box for specifying the name of a new data migration job group.
2–Understanding the User Interface Shortcut Menus Table 2-3. Shortcut Menu Options (Continued) Option Description FCIP Route Remove Launches a wizard to select an FCIP route to delete. FW Update Wizard Launches a wizard for updating the router’s firmware. iSCSI Target Map Wizard Opens a dialog box to present multiple iSCSI targets (with a single LUN per target) into a single Fibre Channel target. License an Array Launches a wizard to select an array for unrestricted data migration capacity.
2–Understanding the User Interface Tree Pane Table 2-3. Shortcut Menu Options (Continued) Option View Logs Description Opens the Router Log dialog box for either system or data migration log messages. Tree Pane The left pane of the SANsurfer Router Manager window contains a “tree” view of the router and services. The tree pane contains two tabbed pages: The tree on the Router page (see Router Tree) shows the connected systems and their components.
2–Understanding the User Interface Tree Pane Figure 2-3.
2–Understanding the User Interface Tree Pane “Arrays” on page 3-34 “iSCSI Presented Targets” on page 3-35 “FCIP Routes” on page 3-37 Click a component in the router tree in the left pane to view component details in the pages in the right pane (the information, configuration, and data pane). Figure 2-4 shows an example. Figure 2-4.
2–Understanding the User Interface Status Icons and Text Services Tree The services tree (Figure 2-5) appears in the left pane of the SANsurfer Router Manager window when the Services tab is selected. Services are licensed features of SANsurfer Router Manager. Figure 2-5. Services Tree Pane (Example) Click a component in the services tree in the left pane to view service details in the pages in the right pane (the information, configuration, and data pane).
2–Understanding the User Interface Status Icons and Text Router Located at the root folder of the tree, each router node shows the following: Router status icon indicates operational status (blinking heartbeat). Router model identifies the model: iSR6152. Example: Router iSR6152 Router icons Online router. The blinking heart on the router icon indicates that the connection between SANsurfer Router Manager and the agent is active for this router.
2–Understanding the User Interface Status Icons and Text Discovered FC and iSCSI Initiators Nested beneath the Router node, the Discovered FC Initiators and Discovered iSCSI Initiator nodes identify the initiators logged into the router. Example: iqn.1991-05.com:microsoft:winhaz14 Initiator icons iqn.nnnn-nn.com.xxxxx:xxxnnnn is the initiator connection. To determine the connection status, select the initiator node in the router tree.
2–Understanding the User Interface Status Icons and Text LUN attached to offline targets. iSCSI Presented Targets Nested beneath the Router node, iSCSI Presented Targets nodes identify one type of target: Presented (targets that the router presents to the hosts) Example: iqn.2004-08.com.qlogic:isr6152.0823e00015.r1.02. 2100000c50a660f1 iSCSI presented target icons Target ID indicates the iSCSI presented target is online. Target ID indicates the iSCSI presented target is offline from the router.
2–Understanding the User Interface Status Icons and Text Data Migration Jobs Nested beneath the Router node, the Data Migration Job nodes identify the data migration, compare, and scrubbing jobs for all data migration groups on the iSR6152. Example: Data Migration Jobs Data Migration Groups Nested beneath the Data Migration Jobs node, the Data Migration Group nodes identify the default (Group 0) and user-created data migration groups.
2–Understanding the User Interface Status Icons and Text 2-18 ISR645610-00 B
3 Viewing Router Information SANsurfer Router Manager lets you monitor and manage the iSR6152 router—as well as its ports and connected devices—by selecting components in the router tree in the left pane (for details, see “Router Tree” on page 2-10). Information, configuration, and data for the selected component appears in the right pane.
3–Viewing Router Information Router iSR6152 Router iSR6152 The top of the SANsurfer Router Manager router tree in the left pane identifies the connected iSR6152 by serial number. Click the router in the left pane to view the following tabbed pages in the right pane: “Information” on page 3-2 “SNMP Management” on page 3-10 “Features” on page 3-12 NOTE: The Assigned Remote Router page appears only if your router’s configuration includes a remote router.
3–Viewing Router Information Router iSR6152 Basic Information Click the first vertical tab on the router’s Information page to view the Basic Information page, as shown in Figure 3-1. Figure 3-1. Router Information: Basic Information Page The Basic Information page provides the following router information and settings: Product Name identifies the router model. Symbolic Name provides a box for you to assign a symbolic name (64 characters maximum) for the router.
3–Viewing Router Information Router iSR6152 Fibre Channel Port Count identifies the quantity of Fibre Channel ports on the router. Temperature shows the router’s current temperature in degrees Centigrade. System Uptime indicates the number of days, hours, minutes, and seconds that this router has been up since booting after the last shutdown or reboot.
3–Viewing Router Information Router iSR6152 Controller LUN Automap. Select Enabled (the default setting) to obtain user-level control for mapping the storage array controller (SCSI Device Type 0x0C). When enabled, the controller LUN is automatically mapped to all hosts. Or, select Disabled to instead manually map the controller LUN to hosts. Time to Target Device Offline.
3–Viewing Router Information Router iSR6152 Management Information Click the second vertical tab on the router’s Information page to view the Management Information page, as shown in Figure 3-2. Figure 3-2. Router Information: Management Information Page The Management Information page provides the following router information: MAC shows the management port’s MAC address. Link Status shows the management port link status: Link Up or Link Down. IPv4 Management Info.
3–Viewing Router Information Router iSR6152 ISR645610-00 B Subnet Mask of the management port Gateway IP of the server acting as a gateway to your Internet connection IPv6 Management Info. Select this check box to use IPv6 (128-bit addressing), and then select one of the following: Click Auto to have the system automatically obtain the first and second IPv6 addresses, default router, and local link.
3–Viewing Router Information Router iSR6152 NTP Server Information Click the third vertical tab on the router’s Information page to view the NTP Server Information page, as shown in Figure 3-3. Figure 3-3. Router Information: NTP Server Information Page The NTP Server Information page provides the following information: 3-8 System Time indicates the current system date and time. Click Disable NTP Servers to disallow NTP servers to set the router’s date and time.
3–Viewing Router Information Router iSR6152 NTP Server 3 specifies the IPv4 or IPv6 of the third NTP server to be queried by the router when setting its time and date. This server is used only if the first and second NTP servers did not respond. Click Set NTP Address to save the changes to the NTP servers IP addresses. Select the Enable iSNS check box to allow input of Internet simple name service (iSNS) server details. Then follow these steps: a. b. c.
3–Viewing Router Information Router iSR6152 SNMP Management The iSR6152 router has an SNMP agent that sends router status information to the SNMP management application. The SNMP Management page includes two sections: SNMP Configuration and Enabled SNMP Trap Receivers, as shown in Figure 3-5. If you make any changes on this page, click the Save button to preserve the SNMP management changes. NOTE: For more information, see Appendix A Simple Network Management Protocol (SNMP). Figure 3-5.
3–Viewing Router Information Router iSR6152 SNMP Configuration The SNMP Configuration options include the following: System OID indicates the vendor’s system object identifier. System Description shows the product description of the router (QLogic iSR6152). SNMP Settings include the following: Read Community: Type a password that authorizes an SNMP management server to read information from the router. This is a write-only box.
3–Viewing Router Information FC Ports Features The Features page lists the router’s current licensed features and lets you apply additional licenses, as shown in Figure 3-6. Figure 3-6. Features Page License Information lists each currently licensed key, description, and date applied. To open the Add License Key dialog box and enter a new license key for another feature, click Add. FC Ports When you click a Fibre Channel port in the router tree, information for that port appears in the right pane.
3–Viewing Router Information FC Ports Information The Information page provides basic information for the selected Fibre Channel port and allows you to enable and disable the port, as shown in Figure 3-7. Figure 3-7. FC Port: Information Page The Information page contains the following port information: Node Name shows the world wide node name (WWNN) assigned to the Fibre Channel port. Port Name shows the world wide port name (WWPN) assigned to the Fibre Channel port.
3–Viewing Router Information FC Ports Advanced Configuration The Advanced Configuration page provides additional configuration options for the selected Fibre Channel port, as shown in Figure 3-8. Figure 3-8. FC Port: Advanced Configuration Page The Advanced Configuration page contains the following options: Connection Options lists the available connection types: Loop Only, Point to Point Only, and Loop Preferred, Otherwise Point to Point.
3–Viewing Router Information FC Ports Figure 3-9. FC Port: Statistics Page To view the most current statistics for this port, click Refresh. To reset all statistical values to zero, click Clear. Performance The Performance page for the selected Fibre Channel port contains a graph depicting read/write performance, as shown in Figure 3-10.
3–Viewing Router Information FC Ports Figure 3-10. FC Port: Performance Page To monitor Fibre Channel port performance: 1. On the Fibre Channel port’s Statistics page, click Set Rate. 2. On the Performance Sampling Rate dialog box, type a Sampling Rate as an integer from 1 to 30, and then click OK. 3. Click Start to begin monitoring. The performance graph reveals port I/O performance, where: 4. 3-16 InitRead shows the initiator’s read performance through the selected Fibre Channel port.
3–Viewing Router Information iSCSI Ports iSCSI Ports When you select an iSCSI port in the router tree, the following tabbed pages appear in the right pane: “Information” on page 3-17 “Advanced Configuration” on page 3-20 “Statistics” on page 3-22 Information The Information page for the selected iSCSI port contains three areas: iSCSI Port Information, iSCSI Port Network Settings, and iSNS, as shown in Figure 3-11.
3–Viewing Router Information iSCSI Ports iSCSI Port Information The iSCSI Port Information area provides the following information and settings: Base Name shows the full name assigned to the selected iSCSI port. Link Status identifies the port connection status: Link Up or Link Down. MAC Address assigned to the port; this parameter is not editable. Actual Port Speed indicates the real speed, for example, 1Gbps/FDX.
3–Viewing Router Information iSCSI Ports IPv6 Default Router identifies the default router for the IPv6. Depending on your network configuration, SANsurfer Router Manager can also dynamically set the IPv6 default router. IPv6 Link Local specifies the IPv6 link local of the port. It is not editable. VLAN IPv6 indicates the VLAN IPv6 configuration as Disabled or Enabled. When enabled, you can configure the following: VLAN ID IPv6 contains an identification value in the range 0 to 4094.
3–Viewing Router Information iSCSI Ports Advanced Configuration Use the Advanced Configuration page to configure the router’s iSCSI port parameters, security settings, and CHAP settings, as shown in Figure 3-12. Figure 3-12. iSCSI Port: Advanced Configuration Page The iSCSI port’s Advanced Configuration page provides the following parameters. If you make any changes on this page, you must click Save (at the bottom of the page) for the change to take effect.
3–Viewing Router Information iSCSI Ports Target TCP Port Number identifies the TCP port number the router uses to receive iSCSI target commands. The iSCSI community uses TCP port number 3260 by default. If you change this TCP port number, you must also change all corresponding iSCSI initiators connecting to this iSCSI target port. IPv6 Settings include the following: Select the Enable IPv6 Window Scaling check box to use this setting. If enabled, select the Scale Factor (valid values are 0–5).
3–Viewing Router Information iSCSI Ports Enable Data Digest enables or disables support for iSCSI data digest. Data digest is an ISCSI feature that adds a validity check to iSCSI data to verify that no corruption has occurred during transmission of the data. The iSR6152 router supports data digest in its hardware to maximize performance. Select the check box to enable this option; clear the check box to disable it.
3–Viewing Router Information VP Groups Figure 3-13. iSCSI Port: Statistics Page To view the most current statistics for this port, click Refresh at the top of the page. To reset all values to zero, click Clear. VP Groups Expand the VP Groups branch in the router tree, and then select a VPGROUP node to view virtual port group details in the right pane, as shown in Figure 3-14. Figure 3-14.
3–Viewing Router Information Discovered FC Initiators The VP Group Information section includes the following details: Index is the VPG index within the router. VP Group Name identifies the name of the selected VP Group. (To change the name, enable the VP Group, type a new name, and then click Save. Refresh the page to see the new name. For details, see “Renaming a Virtual Port Group” in the help system.) Status lets you set the VPG status: Enabled or Disabled.
3–Viewing Router Information Discovered iSCSI Initiators OS Type Selection provides options to select the operating system type for the discovered initiator. The iSR6152 router uses the OS type to enable OS-specific commands. Type options include: Other, MS Windows, Linux, HPUX, Mac, Solaris, VMware, OpenVMS, and Windows 2008. Status is the activity status for the selected initiator, either Logged In (online) or Logged Out (offline).
3–Viewing Router Information Discovered iSCSI Initiators Information The Information page for a discovered iSCSI initiator contains two sections: Initiator Information and CHAP Settings, as shown in Figure 3-17. Figure 3-17. Discovered iSCSI Initiators: Information Page The Initiator Information section provides the following: iSCSI Alias specifies the iSCSI initiator’s alias, which the initiator provides when it logs into the iSR6152 router. iSCSI IP shows the IP of the discovered iSCSI initiator.
3–Viewing Router Information FC Discovered Targets NOTE: To apply any setting changes, click Save. LUN List The LUN List page lists LUNs mapped to the iSCSI initiator, as shown in Figure 3-18. Figure 3-18. Discovered iSCSI Initiator: LUN List Page The LUN List page provides the following parameters: Device Info is the information provided by the target LUN as a result of issuing a SCSI INQUIRY command. Name is the target name. For Fibre Channel targets, the name is the WWPN.
3–Viewing Router Information FC Discovered Targets Expand the VPG branch under the target node, and then select a specific LUN to view the following additional page in the right pane for that VPG: “Discovered LUN Information” on page 3-31 FC Presented Targets The FC Presented Targets page shows information for each Fibre Channel presented target, as shown in Figure 3-19. Figure 3-19.
3–Viewing Router Information FC Discovered Targets Figure 3-20. FC Discovered Targets: iSCSI Presented Target List Page The iSCSI Presented Target List page shows the following data for each iSCSI presented target: Target WWPN IP Address Alias iSCSI Name To send the list of presented targets to a printer, click Print. To save the list to a .CSV file, click Export. Information The Information page for a Fibre Channel discovered target contains non-editable product data, as shown in Figure 3-21.
3–Viewing Router Information FC Discovered Targets The Information page contains the following FC target information: Product Vendor is the product vendor as reported by the SCSI INQUIRY command. Product ID is the product ID as reported by the SCSI INQUIRY command. Product Revision is the product revision as reported by the SCSI INQUIRY command. Target Path specifies either the router port on which the target is discovered, or Offline.
3–Viewing Router Information FC Discovered Targets Alias is the iSCSI alias of the presented target. iSCSI Name is the presented target’s iSCSI name. Discovered LUN Information For an FC Discovered Target, select a target, expand the VPGs below that target, and then select a LUN to view the Discovered LUN Information page in the right pane. This page provides details on the selected Fibre Channel target LUN. Figure 3-23 shows the Discovered LUN Information page. Figure 3-23.
3–Viewing Router Information iSCSI Discovered Targets Size indicates the LUN size in GB. Status is the current state of the LUN, either Online or Offline. iSCSI Discovered Targets The iSCSI Discovered Targets branch on the router tree does not provide any information in the right pane. Select a discovered target to view the Information page for that target, as shown in Figure 3-24. Figure 3-24.
3–Viewing Router Information iSCSI Discovered Targets Product Revision shows the product revision as reported by the SCSI INQUIRY command. IP shows the IP of the presented iSCSI target. iSCSI Name shows the presented iSCSI target’s name. Target Path shows the router’s iSCSI port where the target was discovered. CHAP Settings provides an option you can use to set the CHAP option as follows: Enable CHAP check box allows you to enable CHAP when connecting to this target.
3–Viewing Router Information Arrays Arrays Expand the Arrays branch in the left pane, and then select a specific storage array node to view the Information page for that array in the right pane. Figure 3-25 shows an example. Figure 3-25. Arrays: Information Page The Information page for a storage array contains the following general information, some of which is editable: 3-34 Symbolic Name is the user-defined array name.
3–Viewing Router Information iSCSI Presented Targets Target Type for the array can be specified as either Source, Destination, Src+Dest (both source and destination type), or None. Array Bandwidth can be specified as one of the following: Slow (50BMB/s), Medium (200BMB/s), Fast (1600MB/s), User Defined, or Max Available. User-defined Bandwidth (MB/s) becomes available if the selected Array Bandwidth setting is User Defined. Type an integer in the box.
3–Viewing Router Information iSCSI Presented Targets Figure 3-26. iSCSI Presented Targets: Information Page Information for the selected iSCSI presented target includes: 3-36 iSCSI Name is the presented iSCSI target’s name. iSCSI Alias is the presented iSCSI target’s alias. You can change the alias by typing a valid name in the box. Product Vendor is the product vendor as reported by the SCSI INQUIRY command. Product ID is the product ID as reported by the SCSI INQUIRY command.
3–Viewing Router Information FCIP Routes NOTE: To apply changes made to this window, click Save.
3–Viewing Router Information FCIP Routes FCIP Route Info The FCIP Route Info page contains the information that defines the selected FCIP route, as shown in Figure 3-27. Figure 3-27.
3–Viewing Router Information FCIP Routes The FCIP Route Info page contains the following information and configurable parameters for the currently selected FCIP route. If you make any changes to the FCIP route configuration, click the Save button at the bottom of the page. FCIP Interfaces Status allows you to enable or disable the FCIP route. Disabling the route places the Fibre Channel and GbE ports in a down state, but still retains all route configuration parameters.
3–Viewing Router Information FCIP Routes Jumbo Frames indicates that the use of jumbo Ethernet frames is enabled. Jumbo frames are Ethernet frames with payloads greater than 1500 bytes, with a maximum size of 9000 bytes. Using jumbo frames requires all the network equipment in the route to be configured for jumbo frames. Jumbo frames can increase bandwidth in some networks because the number of headers to be processed is decreased when each frame contains more user data.
3–Viewing Router Information FCIP Routes Table 3-1. TCP Window Scaling Factor TCP Window Size (in bytes) Scale Factor Actual Window Size (in bytes) 32767 0 (scaling disabled) 32,767 32767 1 64,534 32767 2 131,068 32767 3 262,136 32767 4 524,272 32767 5 1,048,544 32767 6 2,097,088 32767 7 4,194,176 32767 8 8,388,352 32767 9 16,776,704 TCP Port Number identifies the TCP port number on which the FCIP server listens for TCP connections; the default value for FCIP is 3225.
3–Viewing Router Information FCIP Routes VLAN Enabled indicates whether the use of virtual LANs is enabled or disabled. The default is Disabled. VLAN ID specifies the VLAN ID assigned to the FCIP route when VLAN use is enabled. The VLAN ID segregates traffic in a LAN, and must be the same on both routers participating in the FCIP route (local and remote routers must be using same VLAN ID) and on the Ethernet switches.
3–Viewing Router Information FCIP Routes Figure 3-28.
3–Viewing Router Information FCIP Routes 3-44 ISR645610-00 B
4 Viewing Service Information SANsurfer Router Manager lets you monitor and manage licensed features such as data migration by selecting components on the Services page in the tree in the left pane (for details, see “Services Tree” on page 2-13). Information, configuration, and data for the selected component appears in the right pane.
4–Viewing Service Information Router iSR6152 Data Migration Info The Data Migration Info page for the router services contains data migration license usage data, as shown in Figure 4-1. Figure 4-1. Data Migration Info Page The Data Migration Info page contains the following information: 4-2 The Data Migration Usage Information section provides the amounts of capacity licensed, consumed, scheduled or in-process, and available.
4–Viewing Service Information Data Migration Jobs Data Migration Jobs When you click a data migration job in the services tree, information for that job appears in the right pane.
4–Viewing Service Information Data Migration Jobs Synchronizing Jobs The data migration job synchronization feature is available only for online data migration. SANsurfer Router Manager for the iSR6152 currently supports only offline data migration. Therefore the Synchronizing Jobs page will not contain any information, as shown in Figure 4-3. Figure 4-3.
4–Viewing Service Information Data Migration Jobs Source Array - LUN indicates the name of the source array and LUN from which data was migrated to the destination LUN. Dest Array - LUN indicates the name of the destination array and LUN to which data was migrated from the source LUN.
4–Viewing Service Information Data Migration Jobs 4-6 ISR645610-00 B
A Simple Network Management Protocol (SNMP) Introduction Simple network management protocol (SNMP) provides monitoring and trap functions for managing the router through third-party applications that support SNMP. The router firmware supports SNMP versions 1 and 2 and a QLogic management information base (MIB) (see page A-2). You may format the traps using SNMP version 1 or 2 (see page A-11).
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) Table A-1. SNMP Properties (Continued) Parameter Description System contact Specifies the name of the person to be contacted to respond to trap events. The name can be up to 64 characters excluding the number sign (#), semicolon (;), and comma (,). The default is undefined. Authentication traps Enables or disables authentication trap generation in response to authentication failures. The default is disabled.
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) System Information The system information objects provide the system serial number, version numbers (hardware, software, and agent), and number of ports (Fibre Channel and GbE). qsrSerialNumber Syntax SnmpAdminString Access Read only Description The system serial number. qsrHwVersion Syntax SnmpAdminString Access Read only Description The system hardware version number.
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) Network Port Table The network port table contains a list of network ports that are operational on the router. The entries in this table include the management port, the iSCSI ports, and the TOE ports on the router. A single gigabit Ethernet port can function as an iSCSI port and a TOE simultaneously; therefore, there may be up to two entries for a given gigabit Ethernet port.
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrNwPortRole Syntax QsrPortRole Access Not accessible Description The operational role of this port: management port, iSCSI port, or TOE. qsrNwPortIndex Syntax Unsigned32 Access Not accessible Description A positive integer indexing each network port in a given role. qsrNwPortAddressMode Syntax INTEGER 1 = Static 2 = DHCP 3 = Bootp 4 = RARP Access Read only Description The method by which the port gets its IP address.
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrGateway Syntax InetAddress Access Read only Description The gateway for this port. qsrMacAddress Syntax IMacAddress Access Read only Description The MAC for this port. qstNwLinkStatus Syntax QsrLinkStatus Access Read only Description The operational link status for this port. qsrNwLinkRate Syntax QsrLinkRate Access Read only Description The operational link rate for this port.
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) QsrFcPortEntry A Fibre Channel port entry consists of the following sequence of objects: qsrFcPortRole QsrPortRole qsrFcPortIndex Unsigned32 qsrFcPortNodeWwn PhysAddress qsrFcPortWwn PhysAddress qsrFcPortId PhysAddress qsrFcPortType Unsigned32 qsrFcLinkStatus QsrLinkStatus qsrFcLinkRate QsrLinkRate qsrFcPortRole Syntax QsrPortRole Access Not accessible Description The operational role of this port: FCP mode or fra
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrFcPortId Syntax PhysAddress Access Read only Description The interface's 24-bit Fibre Channel identifier. qsrFcPortType Syntax Unsigned32 Access Read only Description The type of Fibre Channel port, as indicated by the use of the appropriate value assigned by the Internet Assigned Numbers Authority (IANA). The IANA-maintained registry for Fibre Channel port types can be found at: www.iana.
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) Access Not accessible Description Each entry (row) corresponds to a single sensor.
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) Access Read only Description The current value of the sensor. qsrUpperThreshold Syntax Integer32 Access Read only Description The upper-level threshold for this sensor. qsrLowerThreshold Syntax Integer32 Access Read only Description The lower-level threshold for this sensor. qsrSensorState Syntax INTEGER Access Read only Description The state of this sensor, indicating the health of the system.
A–Simple Network Management Protocol (SNMP) Notifications Notifications The router provides the following notification types: “Notification Objects” on page A-11 “Agent Start Up Notification” on page A-12 “Agent Shut Down Notification” on page A-12 “Network Port Down Notification” on page A-12 “Fibre Channel Port Down Notification” on page A-12 “Sensor Notification” on page A-12 “Generic Notification” on page A-13 The following sections describe these notifications and objects t
A–Simple Network Management Protocol (SNMP) Notifications Agent Start Up Notification The agent startup notification indicates that the agent on the router has started running. qsrAgentStartup uses the following object: qsrEventTimeStamp Agent Shut Down Notification The agent shut down notification indicates that the agent on the router is shutting down.
A–Simple Network Management Protocol (SNMP) Notifications qsrEventTimeStamp qsrEventSeverity Generic Notification The generic notification reports events other than the defined event types. It provides a description object that identifies the event in clear text.
A–Simple Network Management Protocol (SNMP) Notifications A-14 ISR645610-00 B
B Log Messages This appendix provides details about messages logged to a file. The message log is persistent because it is maintained across router power cycles and reboots. Information in Table B-1 is organized as follows: The ID column specifies the message identification numbers in ascending order. The Log Message column indicates the message text shown in the CLI or SANsurfer Router Manager router log. Note that: Log messages for the iSCSI driver module are common to both iSCSI ports.
B–Log Messages The Msg. Type column specifies the log message type, where: NIC = FCIP NIC module System = System module User = User module Error = Error log message Fatal = Fatal log message Info = Informational log message The Description column provides additional information about the log message. Table B-1. iSR6152 Router Log Messages ID Log Message Module Type Msg.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 41077 QLBA_CreateInitiatorObject: Too many initiators App Error Unable to create an object for initiator object; exceeded the maximum number of initiators. 41096 QLBA_DisplayTargetOperationStatus: PCI Error, Status 0x%.2x App Error Process control block status indicates that a PCI error occurred during a target operation.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 41268 QLIS_LoginPduContinue: Missing target name App Error iSCSI Login PDU received without a target name for a normal session. 41270 QLIS_LoginPduContinue: TSIH is 0 but InitiatorName key/value not provided App Error iSCSI Login PDU received without an initiator name key/value.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 41354 QLIS_LoginPduContinue: Unexpected CHAP key detected App Error iSCSI Login rejected due to a CHAP key error.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 41701 QLBI_Passthru: Invalid data length %d bytes App Error Pass-Through command issued by management tool (such as GUI) failed due to invalid data length. 41717 QLBI_Passthru: Invalid data length %d bytes App Error Pass-Through command issued by management tool (such as GUI) was interrupted or timed out.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 42024 QLFC_Logout: No active path to device. WWPN: %.2X%.2X%.2X%.2X%.2X%.2X%.2X%.2X App Error Attempting logout of device for which there is no active path (WWPN not found). 42027 QLFC_Logout: VP Index 0x%x not configured App Error Logout attempted using Fibre Channel VP index that has not been configured. Operation attempted on an unconfigured VP.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 42404 QLIS_InstantiateSession: Maximum number (%d) of allowed hosts already logged in App Error Failed to execute iSCSI Command PDU because its CmdSN is out-of-range. Log message contains the incorrect CmdSN, the valid CmdSN range, the first byte of the CDB, and the data length.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 53584 QLIS_LoginPduContinue: [0x%x] SES_STATE_LOGGED_IN NORMAL App Info iSCSI session full feature login. 53585 QLIS_LoginPduContinue: [0x%x] SES_STATE_LOGGED_IN DISCOVERY App Info iSCSI session discovery login. 53586 QLIS_LoginPduContinue: Initiator: %s App Info iSCSI login of initiator: %s. 53587 QLIS_LoginPduContinue: Target: %s App Info iSCSI login of target: %s.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 54359 QLFC_Logout: Port Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x App Info Fibre Channel login event notification, VP (virtual port) xx. 54683 QLIS_OpenConnectionNotification: Target connection opened (Port %d, DDB %d) App Info iSCSI target connection opened for port %d, data description block (DDB) %d.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 56346 QLMP_CombineMPDevice: Virtual Target Online App Info An array came online. 56347 QLMP_CombineMPDevice: Node Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x App Info WWNN of the array that came online. This is tied with ID 56346. 56348 QLMP_CombineMPDevice: Port Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x App Info WWPN of the array that came online. This is tied with ID 56346.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 56870 QLDM_CreateMigrationObject: Failed to create Source Lun Object App Info Failed to allocate memory for the source LUN of a migration job. 56871 QLDM_CreateMigrationObject: Failed to create Destination Lun Object App Info Failed to allocate memory for the destination LUN of a migration job.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 69941 #%d: QLUtmProcessResponseQueue: Invalid handle %x EntryType %x iSCSI Fatal Response queue entry contains an invalid handle. 69951 #%d: QLSetNvram: QLRebootTimer failed AF %x RS %x Time %d iSCSI Fatal Set NVRAM reboot timer failed. 69964 #%d: QLDisable: QLRebootTimer failed AF %x RS %x Time %d iSCSI Fatal Port disable reboot timer failed.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 70499 #%d: QLProcessResponseQueue: Invalid handle for ET_PASSTHROUGH_STATUS iSCSI Fatal Response queue invalid handle for ET pass-through. 70501 #%d: QLProcessResponseQueue: Invalid entry type in response queue %x iSCSI Fatal Response queue invalid entry type.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 70938 #%d: ql_adapter_up: Failed to initialize adapter iSCSI Fatal iSCSI controller failed to initialize. 72351 #%d: QLProcSrblessiSNSResponse: Invalid handle %x iSCSI Fatal iSCSI controller reported that an SNS response had an invalid handle. 73990 #%d: QLUtmIoctlEnable: Initialize FW failed iSCSI Error iSCSI processor failed firmware initialization.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 74587 #%d: QLIsrDecodeMailbox: Link down iSCSI Error iSCSI processor reported a link down condition. 74656 #%d: QLReadyTimer: Adapter missed heartbeat for %d seconds. Time left %d iSCSI Error Driver failed to receive a heartbeat from the iSCSI processor for the specified number of seconds.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 74800 #%d: QLSetTargetData: No more room in Target Database. iSCSI Error Driver’s target database is full. Use the CLI or GUI to remove unwanted/unused iSCSI targets. 75008 #%d: ql_process_error: OB_TCP_IOCB_RSP_W returned DdbInx 0x%x pTpb %p iSCSI Error A TCP retry for a frame failed on the connection ddbIndex. Tpb contains the frame memory address.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 102423 #%d: qlutm_init: Failed to return diagnostic result to Bridge FC Fatal Fibre Channel processor failed to return diagnostic results. 102656 #%d: QLInitializeAdapter: Reset ISP failed FC Fatal Fibre Channel processor failed reset. 102657 #%d: QLInitializeAdapter: Load RISC code failed FC Fatal Fibre Channel processor firmware load failed.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 102746 #%d: QLProcessResponseQueue: Invalid handle %x, type %x FC Fatal Response queue entry contains an invalid handle. 102752 #%d: QLTimer: Ext Ram parity error exceed limit cnt 0x%x, limit 0x%x, Disabled adapter FC Fatal Fibre Channel processor external SRAM parity error count exceeded limit; Fibre Channel port disabled.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 106813 #%d: QLIsrEventHandler: Unexpected async event (%x), MB1=%x, MB2=%x, MB3=%x, MB4=%x, MB5=%x, MB6=%x, MB7=%x FC Error Fibre Channel processor reported an unexpected asynchronous event. The mailbox registers provide status, event code, and data related to the event.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 107041 #%d: QLUpdateDeviceDatabase 0x%x: GET_ID failed %x FC Error Driver’s host (initiator) database is full. Maximum host database is 64. 107056 #%d: QLUpdateDeviceDatabase 0x%x: out of slots in host database FC Error Drivers host (initiator) database is full.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 119088 #%d: QLIsrEventHandler: LIP occurred (%x): mailbox1 = %x FC Info Fibre Channel loop initialization process (LIP) occurred. The LIP type is reported, as is the contents of the Fibre Channel processor’s mailbox 1 register. 119089 #%d: QLIsrEventHandler: LIP reset occurred (%x): mailbox1 = %x FC Info Fibre Channel LIP reset occurred.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 120374 #%d: QLIsrEventHandler: IDC Completion (%x) %x, %x, %x, %x, %x, %x, %x FC Info For FCoE protocol, the inter-driver communications (IDC) completes. 120375 #%d: QLIsrEventHandler: IDC Notification (%x), %x, %x, %x, %x, %x, %x, %x FC Info For FCoE protocol, the IDC notification comes from another driver.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 139270 QBRPC_Initialize:GetIscsiAdv Mem Allocation error User Error Get iSCSI Advanced API memory allocation failed. 139271 QBRPC_Initialize:GetIsns Mem Allocation error User Error Get iSNS API memory allocation failed. 139272 QBRPC_Initialize:GetFcIntfc Mem Allocation error User Error Get Fibre Channel Interface API memory allocation failed.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 139287 QBRPC_Initialize:LunMask Mem Allocation error User Error Failed memory allocation for Get LUN Mask API. 139288 QBRPC_Initialize:Init Mem Allocation error User Error Failed memory allocation for Initiator API. 139289 QBRPC_Initialize:TgtDevice Mem Allocation error User Error Failed memory allocation for Target Device API.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 139304 QBRPC_Initialize:NtpStats Mem Allocation error User Error Failed memory allocation for NTP Status API. 139305 QBRPC_Initialize:LunList MemAlloc error User Error Failed memory allocation for LUN List API. 139315 QBRPC_FreeResources:Entered User Error RPC free resources entry point.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 139938 FcipRoute#%d Add Failed because relevant FCIP Licence not available App Error FCIP route add/mod failed because an FCIP license is not present. 151842 FW Upgrade performed: new version is: %d.%d.%d.%d User Info A firmware upgrade was performed; the new version is: d.d.d.d. 151843 REBOOT/SHUTDOWN Command from user.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 151897 qapisetbridgebasicinfo_1_svc:Bridge configuration changed User Info Router configuration has changed. 151908 GE%d: Port status changed by user to ENABLED. User Info GE port %d was enabled by user. 151909 GE%d: Port status changed by user to DISABLED. User Info GE port %d was disabled by user. 151910 FC%d: Port status changed by user to ENABLED.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 152083 qapiremoveinitiator_1_svc : Initiator Removed User Info An initiator has been removed. 152096 qapisetmigrfctargets_1_svc: Configuration Changed for migration target User Info A set array was done on one of the arrays. 152099 LogMigration: Error in Writting log file User Info Encountered an error while updating the migration log entry.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 152107 RemoveMigration:%d with Job Id %d and error = %d User Info Failed to remove a migration job with ID specified in the log. 152108 ValidateSerialSchedule: Previous time %ld New time %ld User Info Reset the serial schedule delayed time to invalid if the last serial schedule job was removed.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 172240 FcipRoute#%d: De-encapsulation Error on Receive FCIP Error FCIP route #n Local Node is out of sync with the remote peer. 172245 FcipRoute#%d: Transmit Failure FCIP Error FCIP route #n not able to transmit data. 172246 FcipRoute#%d: Remote Peer Disconnected FCIP Error FCIP route #n remote peer closed connection.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 172301 FcipRoute#%d: Did not get the keepalive msg form remote peer last %lu, curr %lu FCIP Error The FCIP route #n has not been able to communicate with its remote peer for 10 seconds, resulting in a link drop due to a keepalive timeout. 172302 FcipRoute#%d: TCP Link Down, TCP Stats: SACKed=%d TCP Total ReTransmitted=%d FCIP Error The TCP link for FCIP route #n has disconnected.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 205571 QL3xxx:%s: Auto Negotiation error detected NIC Error Ethernet port was not able to negotiate the configured speed. 205572 QL3xxx:eth%d: Unsupported speed portConfig 0x%x NIC Error Ethernet port speed is not supported. 206080 QL3xxx:ql3xxx_probe: cannot allocate ethernet device %s NIC Error Ethernet device could not be configured.
B–Log Messages Table B-1. iSR6152 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 237572 "Failed to kill sys killer %d\n" System Error Failed to kill system task. 237573 Temperature over high threshold %d System Error Router temperature has exceeded the high temperature threshold. 249862 Temperature is back to normal range %d System Info Router temperature has returned to the normal operating range.
Glossary adapter The board that interfaces between the host system and the target devices. Adapter is synonymous with host bus adapter (HBA), host adapter, and adapter board. adapter port A port on the adapter board. adapter port beacon An LED on the adapter. Flashing it enables you to locate the adapter. arbitrated loop A circular (ring) topology (versus point-to-point) where two or more ports can be interconnected, but only two ports can communicate at a time.
iSR6152 Router Manager User’s Guide device A target, typically a disk drive. Hardware such as a disk drive, tape drive, printer, or keyboard that is installed in or connected to a system. In Fibre Channel, a target device. DHCP Dynamic host configuration protocol. Used by networked devices (clients) to obtain various parameters necessary for the clients to operate in an IP network. driver The software that interfaces between the file system and a physical data storage device or network media.
iSR6152 Router Manager User’s Guide FC See Fibre Channel. FC-IP mode Data transportation mode in which the iSR6152 transports Fibre Channel frames over a TCP/IP connection using the FCIP protocol to connect two iSR6152 routers. In FC-IP mode, a port pair (one Fibre Channel port and an IP port on the same router) on local iSR6152 and another port pair on a remote router form a FCIP route. FCIP Fibre Channel over IP.
iSR6152 Router Manager User’s Guide G_Port Generic port. A port that can operate as either an E_Port or an F_Port. A G_Port can determine operating mode at switch port initialization, F_Port when an N_Port attachment is determined, E_Port when an E_Port attachment is determined. See E_Port, F_Port, FL_Port, L_Port, N_Port, NL_Port. generic port See G_Port. heartbeat LED A chassis LED that indicates the router status.
iSR6152 Router Manager User’s Guide loop port See L_Port. LIP Loop initialization process. The initialization process in an arbitrated loop that occurs when the loop is powered up or a new device is added. One function of a LIP is to assign addresses. All data transmission on the loop is suspended during a LIP. load balancing A software feature that improves system performance by balancing device access between multiple ports for maximum resource efficiency. loop initialization process See LIP.
iSR6152 Router Manager User’s Guide NL_Port Node loop port. A port capable of arbitrated loop functions and protocols. An NL_Port connects through an arbitrated loop to other NL_Port and at most a single FL_Port. NL_Ports handle creation, detection, and flow of message units to and from the connected systems. NL_Ports are end ports in virtual point-to-point links through a fabric, such as NL_Port to F_Port to F_Port to N_Port using a single Fibre Channel fabric switch.
iSR6152 Router Manager User’s Guide port instance The number of the port in the system. Each adapter may have one or multiple ports, identified with regard to the adapter as port 0, port 1, and so forth. To avoid confusion when dealing with a system containing numerous ports, each port is assigned a port instance number when the system boots up. Thus port 0 on an adapter might have a port instance number of 8, for example, if it is the eighth port discovered by the system. POST Power on self test.
iSR6152 Router Manager User’s Guide SNMP Simple network management protocol. SNMP is a networking protocol that enables you to monitor the router using third-party applications that use SNMP. storage area network See SAN. target The storage-device endpoint of a SCSI session. Initiators request data from targets. Targets are typically disk drives, tape drives, or other media devices. Typically a SCSI peripheral device is the target but an adapter may, in some cases, be a target.
iSR6152 Router Manager User’s Guide WWULN World wide unique LUN name. Identifiers for SCSI devices are read from page 83 and page 80 of your SCSI block device as based on the SCSI standard. SANsurfer looks for identifiers in the order of: page 83 type 3, page 83 type 2, page 83 type 1, page 80, and lastly page 83 type 0.
iSR6152 Router Manager User’s Guide Glossary-10 ISR645610-00 B
Index A About box, viewing Router Manager version 2-6 about SANsurfer Router Manager 1-9 access control, target 3-4 action menu, See shortcut menu Active Data Migration Jobs page 4-3 adapter definition of Glossary-1 heartbeat missed error B-16 login message B-9 port beacon, definition of Glossary-1 port, definition of Glossary-1 Add License Key dialog box 3-12 adding data management LUN 2-5, 2-8 data migration group 2-5, 2-8 FCIP route 2-5, 2-8 initiator, iSCSI 2-4, 2-8 license key 3-12 LUN, scrubbing 2-5,
iSR6152 Router Manager User’s Guide C CHAP authentication error B-4 configuring 1-x definition of Glossary-1 iSCSI discovered target settings 3-33 iSCSI initiators settings 3-26 iSCSI port settings 3-22 key error B-5 clearing data migration info 4-2 FCIP route statistics 3-42 iSCSI port statistics 3-22, 3-23 router security password 3-9 router statistics values 3-15 security fields 1-11 CLI, definition of Glossary-1 closing SANsurfer Router Manager 1-13, 2-4 command line interface, See CLI community read A
iSR6152 Router Manager User’s Guide disabling authentication trap generation 3-11 CHAP 3-36 NTP servers 3-8 VPG status 3-24 disconnecting from router 2-8 discovered Fibre Channel initiators 3-24, 3-25 Fibre Channel LUNs 3-31 iSCSI initiators 3-25, 3-27 iSCSI targets 3-32 Discovered LUN Information page 3-31 discovering iSCSI targets 2-4, 2-8 driver, definition of Glossary-2 dynamic host configuration protocol, See DHCP E E_Port, definition of Glossary-2 EEPROM definition of Glossary-2 updated message B-17
iSR6152 Router Manager User’s Guide Fibre Channel ports 3-12, 4-3 advanced configuration 3-14 FCIP routes 3-39 icon 2-14 information, viewing 3-13 MIB A-6 number of 3-4 performance graph 3-15 performance, viewing graph 3-15 statistics, viewing 3-14 Fibre Channel protocol, See FCP Fibre Channel targets discovered 3-27 presented, information 3-28 field replaceable unit, See FRU File menu 2-3 firmware definition of Glossary-3 loading 3-2 updating 1-3, 2-3, 2-9, 3-2 Firmware Load dialog box 3-2 FL_Port, defini
iSR6152 Router Manager User’s Guide information basic router 3-3 NTP servers 3-8 Information page arrays 3-34 discovered iSCSI initiators 3-26 FC discovered target 3-29 FC targets, discovered 3-29 Fibre Channel discovered initiator 3-24 Fibre Channel ports 3-13 iSCSI discovered targets 3-32 iSCSI ports 3-17 iSCSI presented targets 3-35 router 3-2 storage arrays 3-34 initiators definition of Glossary-4 discovered 3-26 Fibre Channel, discovered 3-24 iSCSI, adding 2-4, 2-8 iSCSI, discovered 3-25 remote target
iSR6152 Router Manager User’s Guide J jumbo frames definition of Glossary-4 FCIP routes 3-40 iSCSI ports 3-21 MTU, setting 3-21 L L_Port, definition of Glossary-4 LEDs adapter port beacon, definition of Glossary-1 heartbeat, definition of Glossary-4 left pane, See tree pane license keys, adding 3-12 licensed arrays 3-35 features 3-12 licensing an array 2-5, 2-9 link rate FCIP routes 3-41 GbE port 3-41 mode 3-18 link status Fibre Channel port 3-13 GbE port 3-39 iSCSI port 3-18 management port 3-6 LIP defin
iSR6152 Router Manager User’s Guide media, definition of Glossary-5 menu bar 2-3 menus File 2-3 Help 2-6 Settings 2-4 shortcut 2-6 View 2-4 Wizards 2-4 MIB definition of Glossary-5 Fibre Channel ports A-6 network ports A-4 notifications A-11 objects A-2 sensors A-8 system A-3 Microsoft Windows, starting SANsurfer Router Manager on 1-5 MTU definition of Glossary-5 jumbo frame options 3-21 N N_Port (node port), definition of Glossary-5 network port table, MIB A-4 settings, iSCSI ports 3-18 network time prot
iSR6152 Router Manager User’s Guide port instance, definition of Glossary-7 ports connection mode 3-13 definition of Glossary-6 Fibre Channel 3-12, 4-3 icons 2-14 ID, Fibre Channel port 3-13 iSCSI 3-17 iSCSI, configuring 1-3 iSCSI, quantity 3-3, 3-20 iSCSI, speed 3-18 name, Fibre Channel port 3-13 pinging 2-9 POST definition of Glossary-7 processor failed message B-17 power on self test, See POST presented targets, iSCSI 3-35 product information, viewing 1-9 name, router 3-3 properties, SNMP A-1 R read co
iSR6152 Router Manager User’s Guide router log definition of Glossary-7 viewing 2-4, 2-6, 2-10 routes, See also FCIP routes RPC definition of Glossary-7 error messages for B-23–B-26 RSCN definition of Glossary-7 update received B-22 S SAN, definition of Glossary-7 SANsurfer Router Manager definition of Glossary-7 exiting 1-13, 2-4 product information, viewing 1-9 requirements 1-1 starting 1-4 saving browser location 1-9 data migration report 4-2 FRU 2-3 logs and configuration info 2-4 scanning for devices
iSR6152 Router Manager User’s Guide Statistics page FCIP routes 3-42 Fibre Channel ports 3-14 iSCSI ports 3-22 status Fibre Channel ports 3-13 icons 2-13 iSCSI ports 3-18 storage area network, See SAN storage arrays, See arrays Subnet mask, FCIP routes 3-39 switched fabric, definition of Glossary-2 symbolic name, router 3-3 Synchronizing Jobs page 4-4 system contact A-2 location, router A-1 log level 3-4 logs, viewing 2-4 MIB A-3 OID 3-11 time, NTP server 3-8 T targets definition of Glossary-8 devices, re
iSR6152 Router Manager User’s Guide V verifying jobs, configuring 2-5, 2-8 version hardware 3-3 Router Manager, viewing 2-6 software 3-3 View Logs button 2-6 View menu 2-4 viewing help system 1-7 logs 2-10 router information 3-2, 4-1 virtual LAN, See VLAN virtual logical area network, See VLAN virtual port group (VPG) definition of Glossary-8 details, viewing 3-23 VLAN configuration change message B-27 definition of Glossary-8 FCIP routes 3-42 VPG, See virtual port group VPGROUP node details, viewing 3-23
Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com International Offices UK | Ireland | Germany | France | India | Japan | China | Hong Kong | Singapore | Taiwan © 2011 QLogic Corporation. Specifications are subject to change without notice. All rights reserved worldwide. QLogic and the QLogic logo are trademarks or are registered trademarks of QLogic Corporation. AMCC is a registered trademark of Applied Micro Circuits Corporation.
