iSR6200 Router Manager User’s Guide ISR654602-00 H
iSR6200 Router Manager User’s Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
iSR6200 Router Manager User’s Guide Added Windows 2012 as an OS type available for discovered Fibre Channel and iSCSI initiators. Fibre Channel “Information” on page 3-37 Updated the screen shot (Figure 3-27) of the FC Presented Target page. “FC Presented Target” on page 3-45 Added information for the new Host Entities node. “Host Entities” on page 3-71 Updated the screen shot (Figure 4-1) to reflect removal of the Automatic Report Upload button.
iSR6200 Router Manager User’s Guide iv ISR654602-00 H
Table of Contents Preface Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What’s in This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What’s in the Help System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Documentation Conventions . . . . . . . . . . . . . . . . . . . .
iSR6200 Router Manager User’s Guide 2 Understanding the User Interface Main Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . File Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . View Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Settings Menu .
iSR6200 Router Manager User’s Guide 3 Viewing Router Information Router iSR6200 Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Router iSR6200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chassis Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blade x Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Cooling Module x. . . . . . . . . . . . . . . . . . . . . . .
iSR6200 Router Manager User’s Guide Discovered iSCSI Initiators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Initiator Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LUN List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSR6200 Router Manager User’s Guide 4 Viewing Service Information Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Migration Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Migration Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Data Migration Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Synchronizing Jobs . . . . . . .
iSR6200 Router Manager User’s Guide List of Figures Figure Page i Example: Jagged Edges Depict Partial Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . xvii 1-1 Connect to Router Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 1-2 Browser Location Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 1-3 About SANsurfer Router Manager Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSR6200 Router Manager User’s Guide 3-32 3-33 3-34 3-35 3-36 3-37 3-38 3-39 3-40 3-41 3-42 4-1 4-2 4-3 4-4 4-5 SAN-over-WAN Devices: Information Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAN-over-WAN Devices: iSCSI Presented Target Page . . . . . . . . . . . . . . . . . . . . . Remote Mapped Devices: Remote Information Page . . . . . . . . . . . . . . . . . . . . . . . Arrays: Information Page for Source and Src+Dest Arrays . . . . . . . . . . . . . . . . . . .
iSR6200 Router Manager User’s Guide xii ISR654602-00 H
Preface This guide describes the QLogic® SANsurfer® Router Manager features used to configure and manage the QLogic iSR6200 intelligent Storage Router (iSR). For hardware installation, configuration, and diagnostic details, see the iSR6200 QLogic intelligent Storage Router (iSR) Installation Guide. Intended Audience This guide is for users who are responsible for installing, managing, and servicing the iSR6200 router and the SAN equipment to which it is attached.
Preface What’s in the Help System Appendix A Simple Network Management Protocol provides reference material for the simple network management protocol (SNMP) protocol, which you can use to manage the iSR6200 router using a third-party SNMP management application. Appendix B Log Messagesprovides reference material on messages logged to a file, which you can retrieve using the View Log feature. (For details, see “Using the Router Log” in the help system.
Preface Related Materials Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification, RFC2463 Transmission of IPv6 Packets over Ethernet Networks, RFC2464 iSCSI draft standard deaft-ietf-ips-iSCSI-20 Internet engineering task force (IETF): iSCSI Requirements and Design Considerations, iSCSI Naming and Discovery, Internet Protocol Specification (IPv4), RFC793 Transmission Control Protocol (TCP) Specification, RFC1122, Requirements for Internet Host
Preface Documentation Conventions Documentation Conventions This guide uses the following documentation conventions: NOTE CAUTION indicates the presence of a hazard that could cause damage to equipment or loss of data. Text in blue font indicates a hyperlink (jump) to a figure, table, or section in this guide, and links to Web sites are shown in underlined blue. For example: xvi provides additional information.
Preface License Agreements Section titles between quotation marks identify related sections within this guide or topics within the help system. Screen shots that depict only that portion of the interface currently under discussion are shown with jagged edges, as shown in Figure i. Figure i. Example: Jagged Edges Depict Partial Interface License Agreements Refer to the QLogic Software End User License Agreement for a complete listing of all license agreements affecting this product.
Preface Technical Support For details about available service plans, or for information about renewing and extending your service, visit the Service Program Web page: http://www.qlogic.com/Support/Pages/ServicePrograms.aspx Downloading Updates The QLogic Web site provides periodic updates to product firmware, software, and documentation. To download firmware, software, and documentation: 1. Go to the QLogic Downloads and Documentation page: http://driverdownloads.qlogic.com 2.
Preface Technical Support Contact Information QLogic Technical Support for products under warranty is available during local standard working hours excluding QLogic Observed Holidays. For customers with extended service, consult your plan for available hours. For Support phone numbers, see the Contact Support link at http://support.qlogic.com. Support Headquarters QLogic Corporation 4601 Dean Lakes Blvd. Shakopee, MN 55379 USA QLogic Web Site www.qlogic.com Technical Support Web Site http://support.
Preface Technical Support xx ISR654602-00 H
1 Getting Started SANsurfer Router Manager is a GUI consisting of menus, buttons, and windows that you can use to manage iSR6200 routers from a workstation on Linux®, Windows®, Solaris®, or Mac OS® X platform. You can view and change network, port, security, and mapping configuration for one or more iSR6200 routers. SANsurfer Router Manager shows the most current system information. This chapter provides information to help you get started using SANsurfer Router Manager.
1–Getting Started System Requirements System Requirements Table 1-1 lists the SANsurfer Router Manager minimum system requirements for the platform, hardware, and software. Table 1-1. System Requirements Component Operating System Minimum Requirements One of the following: Windows 2000, 2003 Windows 2008 (when available) Linux Red Hat® Enterprise 3.x Linux Red Hat Enterprise 4.x Linux Red Hat 5 SUSE® Linux 9.0 Enterprise SUSE Linux 10.
1–Getting Started Connecting the Management Workstation to the Router Connecting the Hardware SANsurfer Router Manager requires an Ethernet connection to the router using either of the following hardware configurations: Indirect Ethernet connection from the management workstation to the router RJ-45 connector through an Ethernet switch or hub. This requires a 10/100 Base-T straight cable. Direct Ethernet connection from the management workstation to the router RJ-45 Ethernet connector.
1–Getting Started Connecting the Management Workstation to the Router Configuring the Router Ports To configure router ports, select a Fibre Channel or iSCSI port in the left pane (tree pane), and then complete the Information and Advanced Configuration pages for that port in the right pane. For details, see “FC Ports” on page 3-22 and “iSCSI Ports” on page 3-28. Updating the Firmware The router comes with current firmware installed.
1–Getting Started Starting SANsurfer Router Manager 6. 7. Use the Confirm Changes dialog box to review the firmware status and confirm the changes as follows: a. Review the list of routers to be updated with the specified firmware file. b. If you want to save a copy of this firmware configuration, click Save Configuration to File. Browse to the appropriate directory, enter a file name, and then click Save. Click Next.
1–Getting Started Connecting SANsurfer Router Manager to the Router Starting SANsurfer Router Manager on Linux or Solaris On Red Hat/SUSE Linux and Solaris SPARC/x86 systems, follow these steps to start SANsurfer Router Manager. To start SANsurfer Router Manager on Linux or Solaris: 1. Ensure that you are in a graphical user environment, such as Xwindows. 2. Open a command terminal. 3. Change to the directory where you installed SANsurfer Router Manager. 4.
1–Getting Started Getting Help Right-click anywhere in the router tree, and then on the shortcut menu, click Connect. 2. In the Connect to Router dialog box (Figure 1-1), type the IP address or host name, or click the down arrow to select the address or name of a previously connected host. Figure 1-1. Connect to Router Dialog Box 3. Click Connect. When SANsurfer Router Manager connects to a new iSR6200 router, it adds the router node to the top of the list in the router tree.
1–Getting Started Getting Help Viewing the Help System You can view the application help for SANsurfer Router Manager at any time using one of the following methods: To view the help system from the main window, point to the Help menu, and then click Browse Contents. The help system opens in the browser you selected using the Set Browser Location option (see “Specifying the Help Browser” on page 1-8). The help window contains a navigation pane on the left and a topic pane on the right.
1–Getting Started Getting Help To specify a browser: 1. On the SANsurfer Router Manager main window, open the Help menu, and then click Set Browser Location. The Browser Location dialog box opens (Figure 1-2). Figure 1-2. Browser Location Dialog Box 2. In the Browser Location box, type the location of the browser program file. Be sure to specify the path and file name. If you do not know the location, click Browse to search for and select the browser program file.
1–Getting Started Setting Security Figure 1-3. About SANsurfer Router Manager Box The About box provides the following information: 2. Product name Version number Copyright information To close the About box and return to the SANsurfer Router Manager main window, click OK. Setting Security SANsurfer Router Manager security ensures that any router configuration changes require password authorization.
1–Getting Started Setting Security Save the router blade’s configuration and persistent data as a FRU to a TGZ file Restore the router blade’s configuration and persistent data from an existing file NOTE The default SANsurfer Router Manager access password is config. To ensure router security, change this password after installation. To set the access password: 1. In the router tree, select the router blade for which you want to set the access password. 2. Click the Information tab. 3.
1–Getting Started Setting Tree View Options 4. Under Application Access, complete the following boxes: Current Password: Type the existing login password. NOTE The default password is config. New Password: Type the new password. Verify New Password: Type the new password again to confirm the new password. NOTE If necessary, click Clear Fields to clear the typed entries in the Security page text boxes. 5. To update the access password, click Apply.
1–Getting Started Refreshing the Host Configuration Figure 1-5 shows an example. Figure 1-5. Customize Tree View Dialog Box 3. Click OK to save your changes and close the dialog box. SANsurfer Router Manager refreshes the view, and then shows or hides nodes in the router tree pane per your selections. Refreshing the Host Configuration The host configuration (including the router tree) shown in the SANsurfer Router Manager interface does not automatically update all configuration changes.
1–Getting Started Exiting SANsurfer Router Manager Figure 1-6. Refresh Dialog Box Exiting SANsurfer Router Manager To exit SANsurfer Router Manager, choose one of the following options: 1-14 On the SANsurfer Router Manager main window, open the File menu, and then click Exit. On the SANsurfer Router Manager main window, click the Close button in the upper right corner. Press the ALT+X keys.
2 Understanding the User Interface This chapter describes the components of the SANsurfer Router Manager user interface, including: “Main Window” on page 2-2 “Menu Bar” on page 2-3 “Toolbar” on page 2-7 “Shortcut Menus” on page 2-8 “Tree Pane” on page 2-11 “Status Icons and Text” on page 2-15 ISR654602-00 H 2-1
2–Understanding the User Interface Main Window Main Window The SANsurfer Router Manager interface includes a menu bar, a toolbar, a tree pane, and an information/configuration/data pane with tabbed pages, as illustrated in Figure 2-1 and described in Table 2-1. Menu Bar Status Bar Tree Pane Toolbar Tabs Information, Configuration, and Data Pane Figure 2-1.
2–Understanding the User Interface Menu Bar Table 2-1. Interface Description Item Description Menu Bar The menu bar provides access to system functions and wizards. For details, see “Menu Bar” on page 2-3. Toolbar The toolbar buttons provide quick access to common functions: Connect, View Logs, and Refresh. For details, see “Toolbar” on page 2-7.
2–Understanding the User Interface Menu Bar File Menu The File menu provides the following options: FW Update Wizard launches the FW Update Wizard, which enables you to update the iSR6200 router’s firmware image. (For details, see “Updating the Firmware” on page 1-4.) Save FRU preserves the router’s configuration and persistent data by saving it to a file. (For details, see “Saving and Restoring Blade Configuration” in the help system.
2–Understanding the User Interface Menu Bar The Wizards menu provides the following options: Add Initiator Wizard launches the Add Initiator Wizard, which enables you to configure the IP address and other parameters for an iSCSI initiator. Add Host Entity Wizard launches the Add Host Entity Wizard, which enables you to create a host entity: a logical construct consisting of zero or more initiator ports for one or more protocols.
2–Understanding the User Interface Menu Bar 2-6 License an Array launches the Data Migration License Array wizard, which enables you to select an array for unrestricted data migration capacity. The router must have been provided an array license. (Data migration is an optional, licensed feature of SANsurfer Router Manager.) Scrubbing LUN opens the Create LUN Scrubbing Job dialog box, which enables you to wipe out data residing on the LUN.
2–Understanding the User Interface Toolbar NOTE Detailed procedures for the wizards are included in the “Using the Wizards” section of the help system. Help Menu The Help menu provides the following options: Set Browser Location specifies the browser that launches when you view the help system for SANsurfer Router Manager. For procedures, see “Specifying the Help Browser” on page 1-8. Browse Contents launches the help system for SANsurfer Router Manager.
2–Understanding the User Interface Shortcut Menus Shortcut Menus The shortcut menus (Figure 2-2) provide quick access to actions and wizards available elsewhere in SANsurfer Router Manager. To open a shortcut menu, right-click anywhere within the tree pane on the Router or Services pages.
2–Understanding the User Interface Shortcut Menus Table 2-3 provides a description of each shortcut menu option, listed alphabetically. Table 2-3. Shortcut Menu Options Option Description Add Group a Opens a dialog box for specifying the name of a new data migration job group. Add Host Entity Wizard Launches a wizard for creating a host entity, a logical construct consisting of zero or more initiator ports for one or more protocols. (For procedures, see “Add Host Entity Wizard” in the help system.
2–Understanding the User Interface Shortcut Menus Table 2-3. Shortcut Menu Options (Continued) Option Description FCIP Route Remove Launches the FCIP Routes Remove Wizard, which allows you to select an FCIP route to delete. FW Update Wizard Launches a wizard for updating the router’s firmware (For procedures, see “FW Update Wizard” in the help system). Import Remote Array Wizard Opens the Import Remote Array Wizard dialog box to select a remote array to import to this router.
2–Understanding the User Interface Tree Pane Table 2-3. Shortcut Menu Options (Continued) Option a Description Remove Offline Target Deletes the selected offline Fibre Channel target. This option is available only when an offline Fibre Channel target is selected (highlighted) in the router tree. (For procedures, see “Removing a Device” in the help system.) Remove Remote Peer Wizard Launches a wizard to remove a local-to-remote router peer assignment.
2–Understanding the User Interface Tree Pane Router Tree The router tree (Figure 2-3) appears in the left pane of the SANsurfer Router Manager window when the Router tab is selected. Figure 2-3.
2–Understanding the User Interface Tree Pane The router tree contains the connected iSR6xxx routers and the following components for each router: “Router Chassis” on page 2-16 “Router Blade” on page 2-16 “Remote Peers” on page 2-17 “FC, FCoE, and iSCSI Ports” on page 2-17 “VP Groups” on page 2-18 “Discovered FC and iSCSI Initiators” on page 2-18 “FC and iSCSI Discovered Targets” on page 2-18 “iSCSI and FC Presented Targets” on page 2-19 “SAN-over-WAN Devices” on page 2-19
2–Understanding the User Interface Tree Pane Click a component in the router tree in the left pane to view component details in the pages in the right pane (the information, configuration, and data pane; Figure 2-4 shows an example). Figure 2-4. Component Information Pane Example Component information for the selected router includes router chassis, blade, port, status, and discovered device details.
2–Understanding the User Interface Status Icons and Text Services Tree The services tree (Figure 2-5) appears in the left pane of the SANsurfer Router Manager window when the Services tab is selected. Services are licensed features of SANsurfer Router Manager. Figure 2-5. Services Tree Pane (Example) Click a component in the services tree in the left pane to view service details in the pages in the right pane (the information, configuration, and data pane).
2–Understanding the User Interface Status Icons and Text “FC and iSCSI Discovered Targets” on page 2-18 “iSCSI and FC Presented Targets” on page 2-19 “SAN-over-WAN Devices” on page 2-19 “Remote Mapped Devices” on page 2-19 “FCIP Routes” on page 2-20 “Arrays” on page 2-20 “Data Management LUNs” on page 2-20 “Host Entities” on page 2-20 Router Chassis Located at the root folder within the router tree, each router node shows the following: Router status icon indicates an ope
2–Understanding the User Interface Status Icons and Text Blade 1 or 2. A red icon indicates the blade is not operating properly. Remote Peers Nested beneath the Blade node, the Remote Peers nodes show the following: Remote peer status icon colors indicate the remote peer’s operational status. IP address assigned to the remote peer router. Example: 172.17.54.99 Remote peer icons A gray icon indicates the remote peer is operating properly.
2–Understanding the User Interface Status Icons and Text VP Groups Nested beneath the Blade node, VP Groups nodes identify virtual port groups (VPGs). Most arrays limit the number of LUNs presented to a single host. You can enable and configure these VPGs to increase the number of supported LUNs on a storage array.
2–Understanding the User Interface Status Icons and Text Example: LUN (0) LUN icons LUN online. LUN attached to offline targets. iSCSI and FC Presented Targets Nested beneath the Blade node, iSCSI Presented Targets and FC Presented Targets nodes identify one type of target: Presented (targets that the router present to the hosts) Example: iqn.2004-08.com.qlogic:isr6200.0823e00015.r1.02.
2–Understanding the User Interface Status Icons and Text Remote mapped device icons Device ID indicates that the remote mapped device is presented. Device ID indicates that the remote mapped device is offline. FCIP Routes Nested beneath the Blade node, FCIP Route nodes identify Fibre Channel over IP (FCIP) routes. A maximum of two FCIP routes are allowed. Example: FCIP Route Info n is enabled. FCIP Route Info n is disabled.
2–Understanding the User Interface Status Icons and Text Example: Serv01 Services Tree Icons The following sections identify the status icons and text contained in the services tree. Data Migration Jobs Nested beneath the Router node, the Data Migration Jobs node identifies the data migration, compare, and scrubbing jobs for all data migration groups on the iSR6200.
2–Understanding the User Interface Status Icons and Text 2-22 ISR654602-00 H
3 Viewing Router Information SANsurfer Router Manager lets you monitor and manage the iSR6200 router—as well as its blades, ports, and connected devices—by viewing and selecting components in the router tree (for details, see “Tree Pane” on page 2-11).
3–Viewing Router Information Router iSR6200 Chassis Router iSR6200 Chassis The top of the router tree shows the iSR6200 router chassis configuration for each router. In the right pane, the Router iSR6200 and License Info pages provide router details. Router iSR6200 To view the chassis, blade, and power cooling module information, click the router node in the router tree, and then click the Router iSR6200 page in the right pane. Figure 3-1 shows an example of the Router iSR6200 page. Figure 3-1.
3–Viewing Router Information Router iSR6200 Chassis The Router iSR6200 page contains the following sections: “Chassis Information” on page 3-3 “Blade x Information” on page 3-3 “Power Cooling Module x” on page 3-4 Chassis Information The Chassis Information section of the Router iSR6200 page provides the following that is common to both blades contained in the chassis: Product Name indicates iSR6200 for the iSR6200 router, which is the product name saved to the chassis serial EEPROM in manuf
3–Viewing Router Information Router iSR6200 Chassis Table 3-1 shows the internal temperature limits set to trigger events or alerts. Table 3-1.
3–Viewing Router Information Router iSR6200 Chassis License Info The License Info page for the Router iSR6200 chassis provides the following licensed feature information (Figure 3-2 shows an example). Figure 3-2. Router Chassis: License Info Page Chassis Serial Number System Licensing Information: For each blade, shows whether the following are Licensed or No (unlicensed).
3–Viewing Router Information Router Blades Data Migration Usage Information: For the router, shows the amounts, in GB, for data migration (“DM”) and data scrubbing (“DS”), including: DM Total Capacity Licensed DS Total Capacity Licensed DM Migration License Consumed DS Migration License Consumed DM Total Capacity In Process/Scheduled DS Total Capacity In Process/Scheduled DM Total Capacity Available DS Total Capacity Available Array Based Licenses Information: For array-based data m
3–Viewing Router Information Router Blades Information The Information page for a blade contains vertical tabs with icons that identify its content: Basic Information, Management Information, NTP Server Information, and Security. It also contains buttons that function as follows: Click Reboot to reboot the router blade. Click FW Load to open the Firmware Load dialog box and update the router firmware. (For more information, see “Updating the Firmware” on page 1-4.
3–Viewing Router Information Router Blades Basic Information The first vertical tab on the Information page (Figure 3-3) shows the router blade's basic information. Figure 3-3. Blade Information: Basic Information Page The Basic Information page provides the following: 3-8 Product Name identifies the router model. Symbolic Name provides a box for you to assign a symbolic name to the router blade. Serial Number indicates the router blade’s serial number.
3–Viewing Router Information Router Blades Hardware Version identifies the router blade hardware version number. Starting with version 6, the hardware supports IPv6. Software Version identifies the version of firmware loaded on the router blade. IPv6 requires software version 2.4.0.0 or later. iSCSI Port Count specifies the number of iSCSI ports (4) on the selected router blade. Fibre Channel Port Count specifies the number of Fibre Channel ports (2) on the selected router blade.
3–Viewing Router Information Router Blades Target Presentation Mode: Use this setting to specify whether the Fibre Channel targets are automatically or manually presented into iSCSI SAN. Select Auto (the default and recommended setting) to have the Fibre Channel target are automatically presented into iSCSI SAN. Or, select Manual to manually present the Fibre Channel targets into the iSCSI SAN using the targetmap add command in the CLI or the Target Map Wizard in the GUI.
3–Viewing Router Information Router Blades Management Information Click the second vertical tab on the router blade’s Information page to view the Management Information page, as shown in Figure 3-4. Figure 3-4. Blade Information: Management Information Page The Management Information page for a blade provides the following: MAC Address specifies the management port’s MAC address. Link Status shows the management port link status as Link Up or Link Down.
3–Viewing Router Information Router Blades IPv4 Management Info: Select this check box to use IPv4 (Internet Protocol version 4, 32-bit addressing), and then click the appropriate button to identify whether to use either a dynamic or static IP address: Click Obtain an IP address automatically (DHCP) to have the system automatically obtain the IP address, subnet mask, and gateway through DHCP.
3–Viewing Router Information Router Blades NTP Server Information Select the third vertical tab on the router blade’s Information page to view the NTP Server Information page (Figure 3-5). Figure 3-5.
3–Viewing Router Information Router Blades The NTP Server Information page for the blade provides the following options: 3-14 Click Disable NTP Servers to prevent NTP servers from setting the router blade’s date and time.
3–Viewing Router Information Router Blades Security Information Select the fourth vertical tab on the router blade’s Information page to view the Security Information page (Figure 3-6) and change passwords, as needed. Figure 3-6. Blade Information: Security Information The Security Information page enables you to set the router’s application and data migration access passwords. This page provides the following sections: Application Access options: Current Password. Type the current password.
3–Viewing Router Information Router Blades NOTE The default password is migration. 3-16 New Password: Type the new password. Verify New Password: Retype the new password. Apply: Click this button to save the password changes. Clear Fields: Click this button to clear the Current Password, New Password, and Verify New Password boxes.
3–Viewing Router Information Router Blades SNMP Management The iSR6200 router has an SNMP agent that sends router status information to the SNMP management application. The SNMP Management page (Figure 3-7) includes two sections: SNMP Configuration and Enabled SNMP Trap Receivers. Click the Save button to save SNMP management changes. For more information, see Appendix A Simple Network Management Protocol. Figure 3-7.
3–Viewing Router Information Router Blades SNMP Configuration The SNMP Configuration options include the following: System OID indicates the vendor’s system object identifier. System Description shows the product description of the router (QLogic iSR6200). SNMP Settings include the following: Read Community: Type a password that authorizes an SNMP management server to read information from the router. This is a write-only box.
3–Viewing Router Information Router Blades Features The Features page shows the router's licensed features and lets you apply additional license features. Figure 3-8 shows an example. Figure 3-8. Blade: Features Page The Features page provides the following options: License Information lists the router’s licensed features, including the license key, license description, chassis serial number, and the date the license was applied.
3–Viewing Router Information Remote Peers Telnet The Telnet page contains a Telnet session window to the connected router blade. Use Telnet on the LAN connection to access a command line interface (CLI) on a remote machine. Figure 3-9 shows an example. Figure 3-9. Blade: Telnet Page The Telnet page provides the following options: Click Reconnect to reopen a disconnected Telnet session. Click Disconnect to close the current Telnet session.
3–Viewing Router Information Remote Peers Selecting the Remote Peers branch on the router tree does not provide any information in the right pane. Expand the Remote Peers node, and then select a remote peer icon to view the IP address page in the right pane. Figure 3-10 shows an example. Figure 3-10. Remote Peer: [IP Address] Page The IP address page for the selected remote peer contains the following under Remote Router Information: Product Name identifies the remote peer router model number.
3–Viewing Router Information FC Ports Remote Peer Usage Type indicates the peer router’s license usage type that was selected on the Add Remote Peer Wizard. The usage type is one of the following: Data Migration indicates that the peer is licensed to migrate data between local and remote LUNs. Remote Maps indicates that the peer is licensed to connect two individual SANs.
3–Viewing Router Information FC Ports Information The Information page for the selected Fibre Channel port contains details about the port, as shown in Figure 3-11. Figure 3-11. FC Port: Information Page The Fibre Channel port Information page includes the following Port Information details: Node Name is the world wide node name (WWNN) assigned to the FC port. Port Name is the world wide port name (WWPN) assigned to the FC port. Port Status lets you set the port status to Enabled or Disabled.
3–Viewing Router Information FC Ports VP Groups lists the virtual port groups (VPGs) associated with the selected router blade. For each group, the table identifies the VPG Index, VPG Name, Enabled status, WWPN, WWNN, and Port ID for each VPG. If you change the Port Status, click Save to save your changes. A warning message prompts you to verify the status change. Click Yes to proceed, or click No to cancel the status change.
3–Viewing Router Information FC Ports 2. Click Save. The following warning message appears: Changing the following port settings might cause a loss of connection to one or more ports. Do you want to proceed with the save operation? 3. Click Yes to continue saving the changes, or No to cancel the changes. If you click Yes, the Security Check dialog box prompts you to enter the system password. 4. Type the system password, and then click OK.
3–Viewing Router Information FC Ports The FC port Statistics page reports the values for the following FC port parameters: Interrupt Count Target Command Count Initiator Command Count Link Failure Count Loss of Sync Count Loss of Signal Count Primitive Sequence Error Count Invalid Transmission Word Count Invalid CRC Error Count NOTE For more detailed Fibre Channel port statistics, issue the CLI command show stats.
3–Viewing Router Information FC Ports Performance The Performance page for the FC port contains a graph depicting read/write performance, as shown in Figure 3-14. Figure 3-14. FC Port: Performance Page To monitor Fibre Channel port performance: 1. On the FC Port Performance page, click Set Rate. 2. On the Performance Sampling Rate dialog box, type a Sampling Rate as an integer from 1 to 30, and then click OK. 3. Click Start to begin monitoring. The performance graph reveals port I/O performance. 4.
3–Viewing Router Information FCoE Ports FCoE Ports When you click an FCoE port in the router tree, information for that port appears in the right pane. The FCoE port view includes the following pages: Information Advanced Configuration Statistics Performance For information about the FCoE port pages, see “FC Ports” on page 3-22. The FCoE port pages contain the same content as the FC port pages.
3–Viewing Router Information iSCSI Ports Figure 3-15. iSCSI Port: Information Page iSCSI Port Information The iSCSI Port Information area provides the following parameters: Base Name is the full name assigned to the selected iSCSI port. For example: iqn.2004-08.com.qlogic:isr6200.0834e0019.b1 where: iqn.2004-08.com.
3–Viewing Router Information iSCSI Ports Base Name Examples: Before enabling the embedded symbolic name option: iqn.2004-08.com.qlogic:isr6200.0823e00014.b1.02.50001fe150069 d2d After enabling embed symbolic name option (with the symbolic name set to oxygen): iqn.2004-08.com.qlogic:isr6200.0823e00014.b1:oxygen.02.50001f e150069d29 Link Status identifies the port connection status: Link Up or Link Down. MAC Address assigned to the port; this parameter cannot be changed.
3–Viewing Router Information iSCSI Ports VLAN indicates the virtual LAN configuration: Disabled or Enabled. Enable VLAN to configure the following: VLAN ID specifies an identification value in the range 1 to 4094. Priority defines the priority (0 to 7) assigned to this VLAN. IPv6 Address. When using an IPv6 address, define the following parameters: IPv6 Address1 is the first user-assigned IPv6 address to which the port responds.
3–Viewing Router Information iSCSI Ports Advanced Configuration Use the Advanced Configuration page for iSCSI ports to configure the router blade’s port parameters, security settings, and CHAP settings, as shown in Figure 3-16. Figure 3-16.
3–Viewing Router Information iSCSI Ports Advanced iSCSI Port Parameters The Advanced iSCSI Port Parameters section provides the following identifying information: iSCSI Port Number identifies the iSCSI port (1, 2, 3, or 4). Target TCP Port Number identifies the TCP port number that the iSR6200 router blade uses to receive iSCSI target commands. The iSCSI community uses TCP port number 3260 by default.
3–Viewing Router Information iSCSI Ports Security Settings This section provides the following parameters: Enable Header Digest enables or disables support for iSCSI header digest. Header digest is an iSCSI feature that adds a validity check field to iSCSI protocol data unit (PDU) headers to verify that no corruption has occurred during the transmission of the PDU header. The iSR6200 router blade supports header digest in hardware to maximize performance.
3–Viewing Router Information iSCSI Ports Figure 3-17.
3–Viewing Router Information VP Groups VP Groups Expand the VP Groups branch in the router tree, and then select a VPGROUP node to view its details in the right pane, as shown in Figure 3-18. Figure 3-18. VP Groups: VPGROUP_x The VP Group Information section includes the following details: 3-36 Index is VPG index within the router blade. VP Group Name identifies the name of the selected VP Group. (To change the name, enable the VP Group, type a new name, and then click Save.
3–Viewing Router Information Discovered FC Initiators Discovered FC Initiators Selecting the Discovered FC Initiators branch on the router tree does not provide any information in the right pane. Select a specific discovered Fibre Channel initiator node in the router tree to view the following pages in the right pane: “Information” on page 3-37 “LUN List” on page 3-38 Information The Information page for a discovered Fibre Channel initiator contains the initiator information shown in Figure 3-19.
3–Viewing Router Information Discovered iSCSI Initiators LUN List The LUN List page shows the device, name, VP Group name, WWULN, and mapped ID for the discovered Fibre Channel initiator that is selected in the left pane. The LUN column identifies the LUN presented through the array and the Mapped ID column identifies the LUN presented to the host. Figure 3-20 shows an example. Figure 3-20.
3–Viewing Router Information Discovered iSCSI Initiators Information The Information page for a discovered iSCSI initiator contains two sections: Initiator Information and CHAP Settings, as shown in Figure 3-21. Figure 3-21. Discovered iSCSI Initiator: Information Page Initiator Information The Initiator Information section provides the following parameters: iSCSI Alias specifies the iSCSI initiator’s alias, which the initiator provides when it logs into the iSR6200 router blade.
3–Viewing Router Information Discovered iSCSI Initiators CHAP Settings The CHAP Settings section contains the following parameters: Enable CHAP enables or disables CHAP support. Select the check box to enable this option; clear the check box to disable it. CHAP Secret lets you define the CHAP secret used for authenticating an iSCSI client. The box is available only when the Enable CHAP check box is selected. NOTE To apply changes, click the Save button, located at the bottom of window.
3–Viewing Router Information FC Discovered Targets Mapped ID identifies the LUN presented to the host.
3–Viewing Router Information FC Discovered Targets To send the list of presented targets to a printer, click Print. To save the list to a .CSV file, click Export. iSCSI Presented Target List The iSCSI Presented Target List page (when viewed from the FC Discovered Targets node) shows information for each iSCSI presented target, as shown in Figure 3-24. Figure 3-24.
3–Viewing Router Information FC Discovered Targets Information Figure 3-25 shows the Information page for a Fibre Channel discovered target. Figure 3-25. FC Discovered Targets: Information Page The Information page provides the following information about the selected Fibre Channel target: Product Vendor is the product vendor as reported by the SCSI INQUIRY command. Product ID is the product ID as reported by the SCSI INQUIRY command. Device Node Name indicates the worldwide target node name.
3–Viewing Router Information FC Discovered Targets iSCSI Presented Target The iSCSI Presented Target page provides detailed Fibre Channel target information and a list of the iSCSI presentations of the target, as shown in Figure 3-26. Figure 3-26. FC Discovered Target: iSCSI Presented Target Page The iSCSI Presented Target page contains the following information: 3-44 Device Product Vendor is the vendor name of the target device as reported by the SCSI INQUIRY command.
3–Viewing Router Information FC Discovered Targets FC Presented Target The FC Presented Target page provides detailed Fibre Channel target information and a list of the Fibre Channel presentations of the target, as shown in Figure 3-27. This page is only visible if a target map has been created for the selected Fibre Channel discovered target; otherwise the FC Presented Target tab is hidden for the selected FC discovered target. Figure 3-27.
3–Viewing Router Information FC Discovered Targets Discovered LUN Information For an FC Discovered Target, select a target, expand the VPGs below that target, and then select a LUN to view the Discovered LUN Information page in the right pane. This page provides details on the selected Fibre Channel target LUN. Figure 3-28 shows the Discovered LUN Information page. Figure 3-28.
3–Viewing Router Information iSCSI Discovered Targets iSCSI Discovered Targets The iSCSI Discovered Targets branch on the router tree does not provide any information in the right pane. Select a discovered target to view the Information page for that target, as shown in Figure 3-29. Figure 3-29. iSCSI Discovered Targets: Information Page Information The Information page contains the following: iSCSI Name shows the presented iSCSI target’s name.
3–Viewing Router Information iSCSI Presented Targets Header Digest indicates whether or not the header digest is enabled. Log out and Log in buttons provides a way to log out of a logged in target or log into a logged out target. CHAP Settings provides an option you can use to set the CHAP option as follows: Enable CHAP check box allows you to enable CHAP when connecting to this target.
3–Viewing Router Information iSCSI Presented Targets Information The Information page consists of two sections: General Information and CHAP Settings, as shown in Figure 3-30 and described in the following sections. Figure 3-30. iSCSI Presented Targets: Information Page General Information The General Information section contains the following parameters: iSCSI Name is the presented iSCSI target’s name. iSCSI Alias is the presented iSCSI target’s alias.
3–Viewing Router Information FC Presented Targets CHAP Settings The CHAP Settings section provides the following parameters: Enable CHAP enables or disables CHAP (Challenge Handshake Authentication Protocol) support. Select the check box to enable this option; clear the check box to disable it. CHAP Secret lets you define the CHAP secret used for authenticating an iSCSI client. The box is available only when the Enable CHAP check box is selected.
3–Viewing Router Information SAN-over-WAN Devices The Information page contains the following non-editable data: Discovered Node Name is the WWNN of the array’s Fibre Channel target port. Discovered Port Name is the WWPN of the array’s discovered target port. Discovered Port ID is the fabric ID that is assigned to the array’s Fibre Channel target port. Target VPG is the VP group for which the presented target is created. For a global presentation this appears as “GLOBAL.
3–Viewing Router Information SAN-over-WAN Devices Information The Information page for a SAN-over-WAN device shows general, non-editable product and device information, as shown in Figure 3-32. Figure 3-32. SAN-over-WAN Devices: Information Page iSCSI Presented Target The iSCSI Presented Target page for a SAN-over-WAN device shows general, non-editable target device information, as shown in Figure 3-33. Figure 3-33.
3–Viewing Router Information Remote Mapped Devices Remote Mapped Devices Selecting the Remote Mapped Devices branch on the router tree does not provide any information in the right pane. Expand the Remote Mapped Devices branch and select a device to view the Remote Information page in the right pane. Remote Information The Remote Information page for a remote mapped device shows both editable and non-editable device information, as shown in Figure 3-34. Figure 3-34.
3–Viewing Router Information Arrays Expand an array node to view the VP groups for the selected array, and then expand the VPGROUP_x node to view the LUNs for the selected group.
3–Viewing Router Information Arrays Figure 3-36. Arrays: Information Page for Imported Arrays The Information page for a storage array contains the following general information, some of which is editable: Symbolic Name is the user-defined array name. Product Vendor is the product vendor as reported by the SCSI INQUIRY command. Product ID is the product ID of the LUN as reported by the SCSI INQUIRY command.
3–Viewing Router Information Arrays 3-56 Product Revision is the product revision of the LUN as reported by the SCSI INQUIRY command. Target Type for the array can be specified as either Source, Destination, Src+Dest (both source and destination type), or None. Array Bandwidth (for source targets) can be specified as one of the following: Slow (50BMB/s), Medium (200BMB/s), Fast (1600MB/s), User Defined, or Max Available.(This field is shown only for source arrays.
3–Viewing Router Information Arrays Physical Target Ports information includes: Blade ID identifies the iSR6200 blade (1 or 2) on which the array is located. Port specifies the target port number. (This field differs depending on the type of array selected in the router tree.) IQN specifies the target port’s iSCSI qualifying name, or WWPN specifies the target port WWPN for an imported array. (This field differs depending on the type of array selected in the router tree.
3–Viewing Router Information Arrays The Discovered LUN Information page for an array LUN contains the following: Product Vendor is the product vendor as reported by the SCSI INQUIRY command. Product ID is the product ID of the LUN as reported by the SCSI INQUIRY command. Product Revision is the product revision of the LUN as reported by the SCSI INQUIRY command. LUN is the number. WWULN is the world wide unique LUN name. Serial Number is the serial number of the LUN.
3–Viewing Router Information FCIP Routes FCIP Routes Selecting the FCIP Routes branch on the router tree does not provide any information in the right pane.
3–Viewing Router Information FCIP Routes FCIP Route Info Figure 3-39 shows the FCIP Route Info page. Figure 3-39.
3–Viewing Router Information FCIP Routes The FCIP Route Info page contains the following information for the currently selected FCIP route: FCIP Interfaces Status reflects the state (Enabled or Disabled) of the FCIP route, as specified by the user when a route is created or modified. FC Port indicates the Fibre Channel port that is assigned to the corresponding FCIP route. FC Link Status indicates the link state (Up or Down) of the FCIP route. Up indicates the FCIP route is available for use.
3–Viewing Router Information FCIP Routes Select one of the following options for jumbo frames: Jumbo improves data transfer performance, but requires all switches, routers, and devices to support and be configured for jumbo frames. If any of the equipment is not configured for jumbos that device truncates frames that exceed its MTU size (typically 1,500 bytes). Normal is a common setting that works in typical configurations.
3–Viewing Router Information FCIP Routes Table 3-2. TCP Window Scaling Factor (Continued) TCP Window Size (in bytes) Scale Factor Actual Window Size (in bytes) 32767 6 2097088 32767 7 4194176 32767 8 8388352 32767 9 16776704 TCP Port Number indicates the TCP port number on which the FCIP server listens for TCP connections; the default value for FCIP is 3225.
3–Viewing Router Information FCIP Routes VLAN Priority specifies the priority of the VLAN assigned to the FCIP route when VLAN use is enabled. In a network with multiple VLANs, the VLAN Priority box prioritizes Ethernet traffic by giving higher preference to traffic in the network over non-VLAN traffic and traffic from VLANs with lower priorities. Level 1 is the lowest priority, level 7 is the highest priority, and level 0 specifies no VLAN.
3–Viewing Router Information FCIP Routes Statistics For the FCIP route currently selected in the tree pane, the Statistics page lists parameters and values, as shown in Figure 3-40. To update the statistics, click Refresh. To reset all values to zero, click Clear. Figure 3-40.
3–Viewing Router Information FCIP Routes The Statistics page for the selected FCIP route shows the values of the following parameters: 3-66 FC Xmit Frames is the number of Fibre Channel frames transmitted by the Fibre Channel port of the FCIP route. FC Xmit Bytes is the number of Fibre Channel bytes transmitted by the Fibre Channel port of the FCIP route. FC Rcvd Frames is the number of Fibre Channel frames received by the Fibre Channel port of the FCIP route.
3–Viewing Router Information FCIP Routes TCP Xmit Acks is the number of TCP acknowledgements transmitted by the GbE port of the FCIP route. Acknowledgements are sent to inform the peer of data that was successfully received. TCP Rcvd Segment Count is the number of TCP segments received by the GbE port of the FCIP route. TCP Rcvd Byte Count is the number of TCP bytes received by the GbE port of the FCIP route.
3–Viewing Router Information FCIP Routes Ethernet Collision Statistics The following statistics relate to Ethernet collisions that may occur when the Ethernet port is in half-duplex mode. Because half-duplex mode is not currently supported, the values for these statistics should always be zero. 3-68 MAC Xmit Deferrals is the number of Ethernet frame transmissions deferred due to collisions by the GbE port of the FCIP route.
3–Viewing Router Information Data Management LUNs MAC Rcvd Jabbers is the number of “jabber” (long transmission) errors received by the GbE port of the FCIP route. Not valid when the port speed is 1Gbps. MAC Rcvd Carrier Sense Errors is the number of carrier sense errors received by the GbE port of the FCIP route. Not valid when the port speed is 1Gbps. MAC Rcvd Dropped Frames is the number of Ethernet frames dropped by the GbE port of the FCIP route due to inter-packet gap violations.
3–Viewing Router Information Data Management LUNs Page The page lists non-editable information for the selected data management LUN, as shown in Figure 3-41. Figure 3-41. Data Management LUNs: Page The following information is listed under Data Management LUN Info: 3-70 Current Master Blade indicates the blade that was booted up before its peer. That blade becomes the master for the existing DMLs.
3–Viewing Router Information Host Entities LUN State indicates whether the LUN is online or offline. Free/Total Metadata Extents indicates the available and total resources on the data management LUN. Free/Total Data Extents indicates the available and total resources on the data management LUN. Host Entities A host entity is a logical construct consisting of zero or more initiator ports for one or more protocols.
3–Viewing Router Information Host Entities Figure 3-42. Host Entities: Page The following information is listed under Server Info: 3-72 Host Name indicates the symbolic name of the host entity as defined by the user during host entity creation. OS Type Selection indicates the operating system of this host entity group of initiator ports.
4 Viewing Service Information SANsurfer Router Manager lets you monitor and manage licensed features such as data migration by selecting components on the Services page in the tree in the left pane (for details, see “Services Tree” on page 2-15). Information, configuration, and data for the selected component appears in the right pane.
4–Viewing Service Information Blade Blade When you select a blade node in the router tree’s Services page, the Data Migration Info page appears in the right pane. Data Migration Info The Data Migration Info page shows data migration usage and licensing information, and provides options for data migration reporting and parameters, as shown in Figure 4-1. . Figure 4-1.
4–Viewing Service Information Blade The Data Migration Usage Information section provides the amounts of capacity licensed, consumed, scheduled or in-process, and available. The Array Based Licenses Information section provides quantities of migration array-based licenses issued, used, and available. Select the Data Migration Report check box to specify settings for uploading, saving, or clearing information in the data migration report.
4–Viewing Service Information Data Migration Jobs Select the Job Auto-failover Enable check box to cause the job to automatically fail over to the peer blade if the source or destination LUN is unavailable on the owner blade. If auto failover is disabled, you must manually change the ownership of the job to the peer blade. If you make any changes to the Migration Parameters, click Set to save those changes.
4–Viewing Service Information Data Migration Jobs Start Time indicates the date and time that the job began. End Time indicates the date and time that the job finished. Source Array - LUN indicates the name of the source array and LUN from which data is currently being migrated to the destination LUN. Dest Array - LUN indicates the name of the destination array and LUN to which data is currently being migrated from the source LUN.
4–Viewing Service Information Data Migration Jobs Job ID identifies by number the completed migration, compare, or scrubbing job. Job Name identifies by name the completed migration, compare, or scrubbing job. Type shows the job type, either Offline, Migration, Compare, or Scrubbing. Status shows the job state, Completed. % Completed shows the job as 100% finished. Start Time indicates the date and time that the job began.
4–Viewing Service Information Data Migration Jobs Figure 4-5.
4–Viewing Service Information Data Migration Jobs 4-8 ISR654602-00 H
A Simple Network Management Protocol Simple network management protocol (SNMP) provides monitoring and trap functions for managing the router through third-party applications that support SNMP. The router firmware supports SNMP versions 1 and 2 and a QLogic management information base (MIB) (see page A-3). You may format traps using SNMP version 1 or 2.
A–Simple Network Management Protocol SNMP Parameters SNMP Parameters You can set the SNMP properties using SANsurfer Router Manager or the command line interface (CLI). Table A-1 describes the SNMP parameters. Table A-1. SNMP Parameters Parameter Description Read community A password that authorizes an SNMP management server to read information from the router. This is a write-only field. The value on the router and the SNMP management server must be the same.
A–Simple Network Management Protocol SNMP Trap Configuration SNMP Trap Configuration SNMP trap configuration lets you set up to eight trap destinations. Choose from Trap 1–Trap 8 to configure each trap. Table A-2 describes the parameters for configuring an SNMP trap. Table A-2. SNMP Trap Configuration Parameters Parameter a Description Trap n enabled Enables or disables trap n. If disabled, the trap is not configured. Trap address* Specifies the IP address to which the SNMP traps are sent.
A–Simple Network Management Protocol Management Information Base (MIB) qsrNwPortTable Syntax SEQUENCE OF QsrNwPortEntry Access Not accessible Description Entries in this table include the management port and the iSCSI ports on the router. qsrNwPortEntry Syntax QsrNwPortEntry Access Not accessible Description Each entry (row) contains information about a specific network port.
A–Simple Network Management Protocol Management Information Base (MIB) qsrNwPortIndex Syntax Unsigned32 Access Not accessible Description A positive integer indexing each network port in a specified role. qsrNwPortAddressMode Syntax INTEGER 1 = Static 2 = DHCP 3 = Bootp 4 = RARP Access Read-only Description Method by which the port gets its IP address. qsrIPAddressType Syntax InetAddressType Access Read-only Description IP address type: ipv4 or ipv6.
A–Simple Network Management Protocol Management Information Base (MIB) qsrGateway Syntax InetAddress Access Read-only Description Gateway for this port. qsrMacAddress Syntax IMacAddress Access Read-only Description MAC address for this port. qstNwLinkStatus Syntax QsrLinkStatus Access Read-only Description Operational link status for this port. qsrNwLinkRate Syntax QsrLinkRate Access Read-only Description Operational link rate for this port.
A–Simple Network Management Protocol Management Information Base (MIB) qsrFcPortEntry Syntax QsrFcPortEntry Access Not accessible Description Each entry (row) contains information about a specific Fibre Channel port.
A–Simple Network Management Protocol Management Information Base (MIB) qsrFcPortWwn Syntax PhysAddress Access Read-only Description World wide name for this port. qsrFcPortId Syntax PhysAddress Access Read-only Description Interface's 24-bit Fibre Channel address identifier. qsrFcPortType Syntax Unsigned32 Access Read-only Description Type of Fibre Channel port, as indicated by the use of the appropriate value assigned by the Internet Assigned Numbers Authority (IANA).
A–Simple Network Management Protocol Management Information Base (MIB) Initiator Object Table The initiator object table is a list of the iSCSI initiators that have been discovered by the router. There are as many entries in this table as there are iSCSI initiators on the router. qsrIsInitTable Syntax SEQUENCE OF QsrIsInitEntry Access Not accessible Description Entries in this table contain information about initiators.
A–Simple Network Management Protocol Management Information Base (MIB) qsrIsInitName OBJECT-TYPE Syntax SnmpAdminString Access Not accessible Description iSCSI name of the initiator. qsrIsInitAlias OBJECT-TYPE Syntax SnmpAdminString Access Read-only Description Alias for the iSCSI initiator. qsrIsInitAddressType Syntax InetAddressType Access Read-only Description Type of iSCSI initiator’s IP address (IPv4 or IPv6).
A–Simple Network Management Protocol Management Information Base (MIB) qsrIsInitOsType Syntax SnmpAdminString Access Read-only Description The type of the iSCSI initiator’s operating system. qsrIsInitChapEnabled Syntax Integer: 0 = enabled; 2 = disabled Access Read-only Description A value indicating whether CHAP is enabled or not for this iSCSI initiator. LUN Table These tables contains information about the logical unit number (LUN) list.
A–Simple Network Management Protocol Management Information Base (MIB) The QsrLunEntry contains the following sequences of objects. qsrLunWwuln PhysAddress, qsrLunVendorId SnmpAdminString, qsrLunProductId SnmpAdminString, qsrLunProdRevLevel SnmpAdminString, qsrLunSize Unsigned32, qsrLunState INTEGER, qsrLunVPGroupid INTEGER, qsrLunVPGroupname SnmpAdminString qsrLunWwuln Syntax PhysAddress Access Read-only Description The world wide unique LUN name (WWULN) for the LUN.
A–Simple Network Management Protocol Management Information Base (MIB) qsrLunSize OBJECT-TYPE Syntax Units Access Description Unsigned32 Megabytes Read-only Size of the LUN (in megabytes). qsrLunState Syntax Integer 1 = online, 2 = offline, 3 = reserved Access Read-only Description State of the LUN (online or offline). qsrLunVPGroupid Syntax Integer Access Read-only Description ID of the VP group to which this LUN belongs.
A–Simple Network Management Protocol Management Information Base (MIB) qsrVPGroupEntry OBJECT-TYPE Syntax QsrVPGroupEntry Access Not accessible Description Index Each entry in the VP group table.
A–Simple Network Management Protocol Management Information Base (MIB) qsrVPGroupWWNN Syntax VpGroupWwnnAndWwpn Access Read-only Description WWNN for VP group. qsrVPGroupWWPN OBJECT-TYPE Syntax VpGroupWwnnAndWwpn Access Read-only Description World wide port number (WWPN).
A–Simple Network Management Protocol Management Information Base (MIB) A sensor entry contains the following sequence of objects: qsrSensorType INTEGER qsrSensorIndex Unsigned32 qsrSensorUnits INTEGER qsrSensorValue Integer32 qsrUpperThreshold Integer32 qsrLowerThreshold Integer32 qsrSensorState INTEGER qsrSensorType Syntax INTEGER Temperature = 1 Access Not accessible Description Type of data being measured by this sensor.
A–Simple Network Management Protocol Management Information Base (MIB) qsrSensorValue Syntax Integer32 Access Read-only Description Current value of the sensor. qsrUpperThreshold Syntax Integer32 Access Read-only Description Upper-level threshold for this sensor. qsrLowerThreshold Syntax Integer32 Access Read-only Description Lower-level threshold for this sensor.
A–Simple Network Management Protocol Notifications Notifications The router provides the following notification types described in this section: “System Information Objects” on page A-18 “Notification Objects” on page A-19 “Agent Startup Notification” on page A-20) “Agent Shutdown Notification” on page A-20 “Network Port Down Notification” on page A-20 “FC Port Down Notification” on page A-21 “Target Device Discovery” on page A-21 “Target Presentation (Mapping)” on page A-21
A–Simple Network Management Protocol Notifications qsrSwVersion Syntax SnmpAdminString Access Read-only Description System software (firmware) version number. qsrNoOfFcPorts Syntax Unsigned32 Access Read-only Description Quantity of Fibre Channel ports on the system. qsrNoOfGbEPorts Syntax Unsigned32 Access Read-only Description Quantity of gigabit Ethernet (GbE) ports on the system.
A–Simple Network Management Protocol Notifications qsrEventDescription Syntax SnmpAdminString Access Accessible for notify Description A textual description of the event that occurred. qsrEventTimeStamp Syntax DateAndTime Access Accessible for notify Description Indicates when the event occurred. Agent Startup Notification The agent startup notification indicates that the agent on the router has started running.
A–Simple Network Management Protocol Notifications FC Port Down Notification The FC port down notification indicates that the specified Fibre Channel port is down. The next time the port comes up, this event is sent with the qsrEventSeverity object set to clear.
A–Simple Network Management Protocol Notifications Target presentation notifications are sent for the following event: Target Presentation State: Presented (mapped) or unpresented (unmapped) Target name Blade number (1 or 2) VP Group Notification The VP group notification indicates that the specified VP group is enabled or disabled. It also represents change in the name of the VP group.
A–Simple Network Management Protocol Notifications Fans at high speed Fans returned to normal speed PCM number (1 or 2) Fan failed PCM number (1 or 2) PCM un-powered (AC power removed) PCM number (1 or 2) PCM powered (AC power connected) PCM number (1 or 2) PCM removed PCM number (1 or 2) Power Cooling Module (PCM) installed PCM number (1 or 2) PCM number (1 or 2) Fan number (1 of 3) Fan returned to operational state PCM number (1 or 2) Fan number
A–Simple Network Management Protocol Notifications iSCSI port configuration change iSNS configuration change Blade number (1 or 2) Firmware upgrade complete Blade number (1 or 2) Management port configuration change Blade number (1 or 2) Router configuration change Blade number (1 or 2) NTP configuration change Blade number (1 or 2) Port number (1 of 4) Blade number (1 or 2) Reboot blade Blade number (1 or 2) FCIP Route Notification FCIP route notification
B Log Messages This appendix provides details about messages logged to a file. The message log is persistent because it is maintained across router power cycles and reboots. Information in Table B-1 is organized as follows: The ID column specifies the message identification numbers in ascending order. The Log Message column indicates the message text shown in the CLI or SANsurfer Router Manager router log. Note that: Log messages for the iSCSI driver module are common to both iSCSI ports.
B–Log Messages The Msg. Type column specifies the log message type, where: NIC = FCIP NIC module System = System module User = User module Error = Error log message Fatal = Fatal log message Info = Informational log message The Description column provides additional information about the log message. Table B-1. iSR6200 Router Log Messages ID Log Message Module Type Msg.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) Module Type Msg. Type QLBA_CreateInitiatorObject: Too many initiators App Error Unable to create an object for initiator object; exceeded the maximum number of initiators. 41096 QLBA_DisplayTargetOperationStatus: PCI Error, Status 0x%.2x App Error Process control block status indicates that a PCI error occurred during a target operation. 41106 QLBA_DisplayInitiatorOperationStatus: DMA Error, Status 0x%.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 41268 QLIS_LoginPduContinue: Missing target name App Error iSCSI Login PDU received without a target name for a normal session. 41270 QLIS_LoginPduContinue: TSIH is 0 but InitiatorName key/value not provided App Error iSCSI Login PDU received without an initiator name key/value.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) Module Type Msg. Type QLBI_SetPortInfo: QLUT_AllocatePortalObject failed (PortType 0x%x, PortId 0x%x) App Error 41626 QLBI_GetLunInfo: INQUIRY failed, TPB status 0x%x App Error Inquiry command failed. The Inquiry command was issued by the router as part of its discovery process. 41629 QLBI_GetLunInfo: INQUIRY failed, TPB status 0x%x App Error Pass-Through command for Inquiry command for page 83 failed.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 41717 QLBI_Passthru: Invalid data length %d bytes App Error Pass-Through command issued by management tool (such as GUI) was interrupted or timed out. 41750 QLBI_Ioctl: ERROR: Operation (0x%x) not supported in this mode App Error IOCTL operation unsupported. Operation code provided in log message.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type 42027 QLFC_Logout: VP Index 0x%x not configured App Error Logout attempted using Fibre Channel VP index that has not been configured. Operation attempted on an unconfigured VP. 42068 QLFC_HandleTeb: System Error App Error Event notification; Fibre Channel processor encountered a system error (unrecoverable firmware error).
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 42649 QLIS_HandleTeb: Unload Driver App Error Event notification; an IOCTL request was received to unload the iSCSI driver. 42654 QLIS_HandleTeb: iSNS Connection Failed App Error Event notification; attempt to connect to the iSNS server failed. 43265 QLUT_AllocateTpbExtension: TPB allocation failed App Error Failed to allocate memory for TPB extension.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) Module Type Msg. Type QLFC_Login: Origin 0x%x, VP Index 0x%x, Id 0x%x App Info Fibre Channel login occurred, origin xx (1 = adapter, 2 = target, 3 = initiator), VP (virtual port) xx, ID (loop ID) xx. 54275 QLFC_Login: Port ID App Info Fibre Channel login occurred with port ID xx.xx.xx. 54276 QLFC_Login: Node Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x App Info Fibre Channel login occurred with WWNN xx.xx.xx.xx.xx.xx.xx.xx.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 54939 QLIS_HandleTeb: UTM_EC_CLOSE_CONNECTION or UTM_EC_CONNECTION_CLOSED App Info Event notification; iSCSI close connection request or connection closed. 54940 QLIS_HandleTeb: UTM_EC_CLOSE_CONNECTION or UTM_EC_CONNECTION_CLOSED App Info Event notification; iSCSI connection closed.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) Module Type Msg. Type QLDM_ResumeMigration: Failed to resume job: %d, job's current state: 0x%x, error: %d App Info Failed to resume a paused job. 56865 QLDM_DelayedStart:%d Failed to start job : Job ID: %d App Info Failed to start a delayed schedule job. 56866 Lun is already used for of some other migration job App Info Migration add failed because LUN is part of another migration job.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) Module Type Msg. Type Start time got from user %lu Cur Time: %lu Diff: %d App Info The log shows the configured start time and current time for a delayed migration job. 56881 Failed to stop migration job id %u App Info Failed to stop a migration job; the error message includes the job ID. 56884 QLDM_DeleteMigrationJobByLun: Could not find migration object App Info Did not find a migration job for the associated LUN object.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) Module Type Msg. Type #%d: QLEnable: QLRebootTimer failed AF %x RS %x Time %d iSCSI Fatal Port enable reboot timer failed. 70224 #%d: QLProcSrblessiSNSResponse: Invalid handle %x iSCSI Fatal iSNS response contains an invalid handle. 70400 #%d: QLInitializeDevice: QLStartAdapter failed iSCSI Fatal The attempt to start the iSCSI processor failed.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 70524 #%d: QLProcessAen: Invalid event %x iSCSI Fatal Asynchronous event for unknown event type. 70544 #%d: QLRebootTimer: Reboot failed! iSCSI Fatal Reboot timer failed. 70563 #%d: QLRebootTimer: Reboot failed! iSCSI Fatal iSCSI driver missed iSCSI processor heartbeat. iSCSI processor rebooted.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 74056 #%d: QLRunDiag: MBOX Diag test internal loopback failed %x %x iSCSI Error iSCSI processor failed the internal loopback test. 74057 #%d: QLRunDiag: MBOX Diag test external loopback failed %x %x iSCSI Error iSCSI processor failed the external loopback test.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 74660 #%d: QLReadyTimer: Abort pTpb=%p failed, DrvCount 0x%x iSCSI Error iSCSI processor failed to complete an abort request. 74661 #%d: QLTimer: Abort pTpb=%p, Type %x, Timeout 0x%x DrvCount 0x%x, DdbIndex 0x%x iSCSI Error Driver timed out an iSCSI processor operation and is aborting the operation.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 86349 #%d: QLEnable: Restart RISC to update EEPROM iSCSI Info EEPROM updated, restart iSCSI processor (RISC). 86874 #%d: QLIsrDecodeMailbox: Link up iSCSI Info Link up reported by iSCSI processor for GE1 or GE2. 87346 #%d: QLGetFwStateCallback: link 100Mb FDX iSCSI Info iSCSI controller reported a link speed/configuration of 100Mb full-duplex (FDX).
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 102657 #%d: QLInitializeAdapter: Load RISC code failed FC Fatal Fibre Channel processor firmware load failed. 102658 #%d: QLInitializeAdapter: Load ISP2322 receive sequencer code failed FC Fatal Fibre Channel processor receive sequencer code load failed.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 102755 #%d: QLTimer: Heartbeat failed FC Fatal Fibre Channel processor heartbeat failed. 102800 #%d: QLRestartRisc: restart RISC FC Fatal Fibre Channel processor being restarted.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 106851 #%d: QLTimer: Heartbeat failed FC Error Fibre Channel controller failed to provide a heartbeat. 106853 #%d: QLTimer: Link error count (0x%x) exceeded, link down FC Error Driver has determined that the Fibre Channel link is unreliable and unusable due to the number of errors encountered. The link has been taken down.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 107078 #%d: QLUpdatePort 0x%x: out of slots in host database FC Error Driver was unable to re-establish connection to the target within the time-out and retry counts, and is therefore marking it offline. 107984 #%d: QLWriteFlashDword: Write fails at addr 0x%x data 0x%x FC Error Fibre Channel controller failed a Flash write (address x data x).
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 119089 #%d: QLIsrEventHandler: LIP reset occurred (%x): mailbox1 = %x FC Info Fibre Channel LIP reset occurred. The LIP reset type is reported, as is the contents of the Fibre Channel processor’s mailbox 1 register. 119090 #%d: QLIsrEventHandler: Link up (%x) mailbox1 = %x FC Info Fibre Channel link up occurred.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 120375 #%d: QLIsrEventHandler: IDC Notification (%x), %x, %x, %x, %x, %x, %x, %x FC Info For FCoE protocol, the IDC notification came from another driver. 120376 #%d: QLIsrEventHandler: IDC Time Extended (%x), %x, %x, %x, %x, %x, %x, %x FC Info For FCoE protocol, the IDC time extended notification is received.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 139271 QBRPC_Initialize:GetIsns Mem Allocation error User Error Get iSNS API memory allocation failed. 139272 QBRPC_Initialize:GetFcIntfc Mem Allocation error User Error Get Fibre Channel interface API memory allocation failed. 139273 QBRPC_Initialize:GetFcAdv Mem Allocation error User Error Get Fibre Channel Advanced API memory allocation failed.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 139288 QBRPC_Initialize:Init Mem Allocation error User Error Failed memory allocation for Initiator API. 139289 QBRPC_Initialize:TgtDevice Mem Allocation error User Error Failed memory allocation for Target Device API. 139296 QBRPC_Initialize:FcTgt Mem Allocation error User Error Failed memory allocation for Fibre Channel Target API.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 139305 QBRPC_Initialize:LunList MemAlloc error User Error Failed memory allocation for LUN List API. 139315 QBRPC_FreeResources:Entered User Error RPC free resources entry point. 139553 checkDuplicateIp: Detected Error %08x %08x%04x User Error Detected duplicate IP address for management port.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 151842 FW Upgrade performed: new version is: %d.%d.%d.%d User Info A firmware upgrade was performed; the new version is: d.d.d.d. 151843 REBOOT/SHUTDOWN Command from user. Code=%d User Info User issued a REBOOT or SHUTDOWN command. 151889 #%d: qapisetfcinterfaceparams_1_svc: FC port configuration changed User Info Fibre Channel port configuration has changed.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 151908 GE%d: Port status changed by user to ENABLED. User Info GE port %d was enabled user. 151909 GE%d: Port status changed by user to DISABLED. User Info GE port %d was disabled by user. 151910 FC%d: Port status changed by user to ENABLED. User Info Fibre Channel port %d was enabled by user. 151911 FC%d: Port status changed by user to DISABLED.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 152096 qapisetmigrfctargets_1_svc: Configuration Changed for migration target User Info A set array was done on one of the arrays. 152099 LogMigration: Error in Writting log file User Info Encountered an error while updating the migration log entry. Some migration log entries might be missing.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) Module Type Msg. Type ValidateSerialSchedule: Previous time %ld New time %ld User Info Reset the serial schedule delayed time to invalid if the last serial schedule job was removed. 152109 addMigration: Creating migration Job Failed with error %d User Info Failed to create a migration job. 152129 sysTempMon: Left PCM Installed User Info Left power and cooling module (PCM) is or has been installed.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type 152142 sysTempMon: Setting the fan speed to high User Info Fan(s) speed has been set to high. 152143 sysTempMon: Setting the fan speed to normal User Info Fan(s) speed has been set to normal. 152144 sysTempMon: Temperature back to safe value.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) ID Log Message Module Type Msg. Type Description 172249 FcipRoute#%d: FCIP Link Down FCIP Error FCIP link is down for FCIP route #n. 172250 FcipRoute#%d: TCP Link Down FCIP Error TCP link for FCIP route #n has been established. 172253 FcipRoute#%d: Remote Peer IP Address Validation Failed. Expected IP Address: %d.%d.%d.%d, Actual IP Address: %d.%d.%d.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) Module Type Msg. Type ID Log Message 172303 FcipRoute#%d: TCP Link Down, MAC Stats: Tx Dropped Count=%ld Rx Dropped Count=%ld Tx Pause Count=%ld Rx Pause Count=%ld FCIP Error The TCP link for FCIP route #n has disconnected.
B–Log Messages Table B-1. iSR6200 Router Log Messages (Continued) Module Type Msg. Type ID Log Message 206089 QL3xxx:ql3xxx_probe: cannot register network device %s NIC Error The Ethernet port was not able to register as a network device, resulting in a port initialization error for the specified network device. 206114 QL3xxx:eth%d: TCP/IP checksum error TotalChecksumErrorCount = %lu N IC Error The total number of TCP checksum errors detected on the Ethernet link belonging to the eth#%d port.
Glossary adapter The board that interfaces between the host system and the target devices. Adapter is synonymous with host bus adapter (HBA), host adapter, and adapter board. adapter port A port on the adapter board. adapter port beacon An LED on the adapter. Flashing it enables you to locate the adapter. arbitrated loop A circular (ring) topology (versus point-to-point) where two or more ports can be interconnected, but only two ports can communicate at a time.
iSR6200 Router Manager User’s Guide DCBX Data center bridging exchange protocol. Used by DCB devices to exchange configuration information with directly connected peers. The protocol may also be used for misconfiguration detection and for configuration of the peer. device A target, typically a disk drive. Hardware such as a disk drive, tape drive, printer, or keyboard that is installed in or connected to a system. In Fibre Channel, a target device.
iSR6200 Router Manager User’s Guide failover path Software feature that ensures data availability and system reliability by assigning alternate path and automatic adapter failover for device resources. This feature is available only in Windows 2000, Windows Server 2003, Windows Vista, Novell NetWare, Red Hat Linux, and SUSE Linux. (Windows XP and Windows Server 2008 do not support failover.) FC See Fibre Channel.
iSR6200 Router Manager User’s Guide FRU Field replaceable unit. Component that can be replaced in the field upon failure. G_Port Generic port. A port that can operate as either an E_Port or an F_Port. A G_Port can determine operating mode at switch port initialization, F_Port when an N_Port attachment is determined, E_Port when an E_Port attachment is determined. See E_Port, F_Port, FL_Port, L_Port, N_Port, NL_Port. generic port See G_Port. graphical user interface See GUI. GUI Graphical user interface.
iSR6200 Router Manager User’s Guide L_Port Loop port. Does arbitrated loop functions and protocols. NL_Ports and FL_Ports are examples of loop-capable ports. See E_Port, F_Port, FL_Port, G_Port, N_Port, NL_Port. loop port See L_Port. LIP Loop initialization process. The initialization process in an arbitrated loop that occurs when the loop is powered up or a new device is added. One function of a LIP is to assign addresses. All data transmission on the loop is suspended during a LIP.
iSR6200 Router Manager User’s Guide N_Port Node port. Connects by a point-to-point link to either a single N_Port or a single F_Port. N_Ports handle creation, detection, and flow of message units to and from the connected systems. N_Ports are end ports in virtual point-to-point links through a fabric, for example N_Port to F_Port to F_Port to N_Port using a single Fibre Channel fabric switch. See also FL_Port. NL_Port Node loop port. A port capable of arbitrated loop functions and protocols.
iSR6200 Router Manager User’s Guide port Access points in a device where a link attaches. There are four types of ports, as follows: N_Port—a Fibre Channel port that supports point-to-point topology. NL_Port—a Fibre Channel port that supports loop topology. F_Port—a port in a fabric where an N_Port can attach. FL_Port—a port in a fabric where an NL_Port can attach. port instance The number of the port in the system.
iSR6200 Router Manager User’s Guide SFP Small form-factor pluggable. A compact, hot-pluggable transceiver used for both telecommunication and data communications applications. It interfaces a network device mother board (for a switch, router, media converter, or similar device) to a fiber optic or copper networking cable. It is a popular industry format supported by many network component vendors.
iSR6200 Router Manager User’s Guide world wide unique LUN name See WWULN. WWN World wide name. A unique 64-bit address assigned to a device by the device manufacturer. WWNN World wide node name. A unique 64-bit address assigned to a device. WWPN World wide port name. A unique 64-bit address assigned to each port on a device. One WWNN may contain multiple WWPN addresses. WWULN World wide unique LUN name.
iSR6200 Router Manager User’s Guide Glossary-10 ISR654602-00 H
iSR6200 Router Manager User’s Guide Index A about SANsurfer Router Manager 1-9 action menu, See shortcut menu Active Data Migration Jobs page 4-4 adapter definition of Glossary-1 heartbeat missed error B-15 login message B-9 port beacon, definition of Glossary-1 port, definition of Glossary-1 adding data migration job group 2-5 FCIP route 2-6 host entity 2-5 iSCSI initiator 2-5 router, remote 2-6 address identifier, FC port A-8 initiator 3-39 IP of port A-5 IPv4, iSCSI port 3-30 IPv6, iSCSI port 3-31 iSCSI
iSR6200 Router Manager User’s Guide Boolean, help system search 1-8 browser location dialog box 1-9 setting 2-7 specifying for help 1-8 burst length 3-33 buttons, toolbar 2-7 C CHAP authentication error B-4 definition of Glossary-1 iSCSI discovered target settings 3-48 key error B-4 setting iSCSI port 3-34 clearing blade security password 3-16 data migration info 4-3 FC port statistics 3-25 FCIP route statistics 3-65 iSCSI port statistics 3-34 router security password 1-12 CLI definition of Glossary-1 exe
iSR6200 Router Manager User’s Guide device (continued) information 3-40 iSCSI presented target list 3-44 LUN presentation information 3-58 SAN-over-WAN 3-51 devices target, rescanning for 2-7 disabling authentication trap generation 3-18 CHAP 3-34, 3-40, 3-50 data digest 3-34 flow control 3-30 header digest 3-34 jumbo frames 3-33 LUN mask mode 3-9 NTP server 3-14 port status 3-23, 3-30 symbolic name 3-8 VLAN 3-31 VLAN IPv6 3-31 VPG status 3-36 disconnecting from iSR6200 router 2-9 discovered initiators A-9
iSR6200 Router Manager User’s Guide FC ports advanced configuration 3-24 configuring 1-4 down notification A-21 icon 2-17, 2-20 identifier A-8 index A-7 information 3-22 information about A-7 information, viewing 3-23 list of A-6 MIB port table A-6 node 2-17 number of A-19 presented targets 3-45 quantity on blade 3-9 role/mode A-7 statistics, viewing 3-25 table, MIB object group A-6 type of A-8 WWN A-8 WWN of node A-7 WWPN 3-23 FC presented targets 3-50 FCIP, definition of Glossary-3 FC-IP mode, definition
iSR6200 Router Manager User’s Guide H hardware connecting 1-3 version, viewing 3-9, A-18 header digest 3-34 heartbeat LED, definition of Glossary-4 Help menu 2-7 help system browser, specifying location 1-8 viewing 1-8, 2-7 hiding and viewing router tree nodes 1-12 help system navigation pane 1-8 host entities adding 2-5 initiator ports, mapping 2-5 hot replaceable/hot swappable, definition of Glossary-4 I I/O control block, definition of Glossary-4 IANA definition of Glossary-4 FC port types registry A-8
iSR6200 Router Manager User’s Guide IPv6 (continued) management 3-12 port type A-5 IQN, symbolic name 3-8 iSCSI See also iSCSI ports definition of Glossary-4 discovered targets 3-47 initiators, discovered 3-38 presented targets 3-47, 3-48 targets, discovered 3-47 targets, presented 3-44 iSCSI ports advanced configuration 3-32 configuring 1-4 information, viewing 3-28 IPv4 address 3-30 IPv6 address 3-31 network settings 3-30 node 2-17 quantity on blade 3-9 showing information for 3-28 statistics 3-34 iSCSI
iSR6200 Router Manager User’s Guide LUN definition of Glossary-5 discovered LUN information 3-46 information 3-40 list 3-40 mask 3-9 presentation information 3-58 tables A-11 M MAC address iSCSI port 3-30 management port 3-11 network port A-6 Macintosh, starting SANsurfer Router Manager on 1-6 maintenance button, definition of Glossary-5 management IPv4 3-12 IPv6 3-12 port, showing A-3 SNMP 3-17 workstation, definition of Glossary-5 management information base, See MIB mapping host entity to initiator por
iSR6200 Router Manager User’s Guide notifications, SNMP (continued) qsrDscTgtStatusChanged A-21 qsrEventTimeStamp A-20 qsrFCIPRouteNotification A-24 qsrFcPortDown A-21 qsrGenericEvent A-23 qsrPresTgtMapped A-21 qsrSensorNotification A-22 qsrVPGroupStatusChanged A-22 sensor state A-22 target device discovery A-21 target presentation (mapping) A-21 virtual port groups (VPGs) A-22 NTP configuration change notification A-24 definition of Glossary-6 server information 3-13 servers, enabling 3-14 servers, saving
iSR6200 Router Manager User’s Guide ports (continued) icons 2-17 indexing A-5 link rate A-6, A-8 link status A-6, A-8 MAC address A-6 network, showing A-3, A-4 operational role A-4 POST definition of Glossary-7 processor failed message B-17 power and cooling module, See PCM power-on self test, See POST presented targets FC 3-50 Fibre Channel 3-45 iSCSI 3-48, 3-52 notifications, SNMP A-21 product information, viewing 1-9 Q QLogic technical support xvii qsrAgentShutdown notification A-20 qsrAgentStartup not
iSR6200 Router Manager User’s Guide qsrSensorUnits table A-16 qsrSensorValue table A-17 qsrSerialNumber object A-18 qsrSwVersion object A-19 qsrUpperThreshold table A-17 qsrVPGroupEntry table A-14 qsrVPGroupId tables A-14 qsrVPGroupIndex table A-14 qsrVPGroupName table A-14 qsrVPGroupStatus table A-15 qsrVPGroupStatusChanged notification A-22 qsrVPGroupTable table A-13 qsrVPGroupWWNN table A-15 qsrVPGroupWWPN table A-15 R read community password 3-18 setting SNMP properties A-2 rebooting router 2-10 Red H
iSR6200 Router Manager User’s Guide SANsurfer Router Manager definition of Glossary-7 exiting 1-14 product information, viewing 1-9 requirements 1-2 starting 1-5 saving browser location 1-9 data migration report 4-3 FRU 2-4 scanning for devices 2-7 SCSI definition of Glossary-7 INQUIRY command 3-55 searching help system 1-8 security application access 1-11 information, blade 3-15 SANsurfer Router Manager 1-10 settings 3-34 sensors data measurement type A-16 entry/row A-15 index/identifier A-16 listing all
iSR6200 Router Manager User’s Guide status icons 2-15 storage area network, See SAN storage arrays, See arrays subnet mask, port A-5 support, technical xvii switched fabric, definition of Glossary-2 symbolic name 3-8 Synchronizing Jobs page 4-5 system hardware version number, showing A-18 information objects group A-18 OID 3-18 serial number, showing A-18 software/firmware version number, showing A-19 T tables FC ports A-6 LUN A-11 LunVPGroupid A-13 MIB A-3 network ports A-3 qsrFcLinkRate A-8 qsrFcLinkSta
iSR6200 Router Manager User’s Guide targets definition of Glossary-8 devices, rescanning for 2-7 discovery A-21 FC presented 3-50 Fibre Channel presented targets 3-45 iSCSI presented 3-44, 3-47, 3-48 mapping A-21 online/offline A-21 presentation A-21 removing offline 2-11 TCP definition of Glossary-8 max window size 3-34 port number, FCIP routes 3-63 port number, target 3-33 related documents xv technical support xvii temperature, router blade 3-9 terms and definitions Glossary-1 text, status 2-15 time eve
iSR6200 Router Manager User’s Guide world wide node name, See WWNN world wide port name, See WWPN world wide unique LUN name, See WWULN WWN definition of Glossary-9 FC port A-8 FC port node A-7 WWNN definition of Glossary-9 FC port 3-23 login message B-9 VP group A-15 WWPN definition of Glossary-9 FC port 3-23 Fibre Channel presented target 3-57 login message B-9 virtual port group A-15 WWULN definition of Glossary-9 discovered LUN 3-46 target LUN 3-40 viewing for LUN A-12 Index-14 ISR654602-00 H
Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com International Offices UK | Ireland | Germany | France | India | Japan | China | Hong Kong | Singapore | Taiwan © 2009–2012 QLogic Corporation. Specifications are subject to change without notice. All rights reserved worldwide. QLogic, the QLogic logo, SANsurfer, and SmartWrite are trademarks or registered trademarks of QLogic Corporation.
