QLogic 12000 Series InfiniBand Switches and Directors Hardware Installation Guide Version 6.
QLogic 12000 Series InfiniBand Switches and Directors Hardware Installation Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice.
Table of Contents Preface Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . License Agreements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contact Information . . . . . . . . . . . . . . . . . . . . . .
QLogic 12000 Series InfiniBand Switches and Directors Hardware Installation Guide Install the Chassis in the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install the C-mounting brackets . . . . . . . . . . . . . . . . . . . . . . . . . Install the Front Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . Connect Equipment to the Ports and Power On the System . . . . . . . . . . . . Connecting Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
QLogic 12000 Series InfiniBand Switches and Directors Hardware Installation Guide Switch-Based QLogic Fabric Manager License Key . . . . . . . . . . . . . . . . . Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A QLogic 12000 Series Product Specifications Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
QLogic 12000 Series InfiniBand Switches and Directors Hardware Installation Guide QLogic 12800 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fan Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removal Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Supply Replacement . . . . . . . . . . . . . . . . . .
Preface This manual describes the hardware installation and initial configuration tasks for the QLogic 12000 series that includes: • The QLogic 12200 36-port fixed configuration InfiniBand switch • The QLogic 12300 36-port configurable InfiniBand switch • The QLogic 12800 series: 12800-180 12800-360 This manual is organized as follows: Preface describes the intended audience and technical support. Section 1 describes the hardware installation and initial configuration tasks.
Preface License Agreements Text in blue font indicates a hyperlink (jump) to a figure, table, or section in this guide, and links to Web sites are shown in underlined blue. For example: Table 9-2 lists problems related to the user interface and remote agent. See “Installation Checklist” on page 3-6. For more information, visit www.qlogic.com. Text in bold font indicates user interface elements such as a menu items, buttons, check boxes, or column headings.
Preface Technical Support Technical Support Customers should contact their authorized maintenance provider for technical support of their QLogic products. QLogic-direct customers may contact QLogic Technical Support; others will be redirected to their authorized maintenance provider. Visit the QLogic support Web site listed in Contact Information for the latest firmware and software updates.
Preface Technical Support 4 D000102-000 B
1 Installation This section describes how to install and configure for first-time use: • The QLogic 12000 switches in a network environment. Planning the Installation The 12000 is designed to be installed in an existing 19-inch equipment rack or server rack. NOTE: These switches are designed for a four-post server cabinet. Do not mount in a two-post telco cabinet. Racks should conform to conventional standards.
1–Installation Planning the Installation Cable Requirements Cable Distances When planning the location of the switches, consider the distance limitations for signaling, EMI, and connector compatibility. It is recommended that the user does not exceed specified transmission rate and distance limits. Cable Guidelines NOTE: Building and electrical codes vary depending on the location. Comply with all code specifications when planning the site and installing cable.
1–Installation Planning the Installation Cable Handling and Bend Radius Provide proper strain relief by adhering to the following guidelines: Table 1-1. IB Copper Cable Guidelines IB Copper Cable Bend Radii American Wire Gauge (AWG) Size Cable Bend Radius 26 2.43 inches 28 2.28 inches 30 1.98 inches For copper cable, the temporary 90-degree bend can never be more than 0.5 inches tighter than the values listed above for any assembly.
1–Installation Planning the Installation Table 1-2.
1–Installation Installation Tasks Checklist Installation Tasks Checklist To perform the actual switch installation, the site implementation engineer must perform the following tasks, which are detailed in this section. CAUTION! Be sure to review the safety information before starting the installation and during the installation process (refer to Appendix B). 1. Check the installation site to verify the installation of cabinet power feeds, rails, and grounding. 2.
1–Installation Installation Tasks Checklist It is recommended that cabinet anti-tip devices are used. This is especially true if installing or removing a switch in the upper half of the cabinet when the lower half is empty. Mark the Rack Allow enough vertical space in the rack for each specific switch installation. 1. Determine the location in the rack of the bottom of the switch. 2. Mark the upper (if applicable) and lower mounting positions on the vertical rails on the front of the rack. 3.
1–Installation 12200/12300 Installation 12200/12300 Installation This section describes the rack mounting instructions for the 12200 and 12300: Management Module Installation NOTE: This section applies to those users who have purchased a managed version of the QLogic 12200. Users with an unmanaged 12200 can skip to the rack mounting instructions. To install the management module in a 12200 switch, follow the steps below: 1. Remove the screw from the blank cover (see Figure 1-3).
1–Installation 12200/12300 Installation Figure 1-4 Insert Management Module 2 4. Close slowly, ensuring that the module connectors connect to the motherboard connectors (Figure 1-5). Figure 1-5 Insert Management Module 3 5. 1-8 Replace the screw that was removed in Step 1 and tighten securely (Figure 1-6).
1–Installation 12200/12300 Installation Figure 1-6 Insert Management Module 4 Four Post Standard-Depth Rack Installation In a standard-depth rack, the distance between the front and back mounting posts is ~28" (700mm). Mounting rails for the 12200 and 12300 are adjustable to accommodate racks with 26"-33" between mounting posts.
1–Installation 12200/12300 Installation side of the switch. On the 12200, hat rails are installed with mounting ears towards the port side of the switch. Figure 1-7 12200 and 12300 Hat Rails 2. Install eight (8) cage nuts into rack posts, two (2) cage nuts per post. Install the mounting rails and fasten to cage nuts using six (6) M6 screws. Torque screws to 30in-lb. Do not install two (2) screws in lower locations on equipment installation side of the rack until the switch is installed in the rack.
1–Installation 12200/12300 Installation 3. Slide the switch into the mounting rails and fasten with M6 screws, one (1) per side. Torque screws to 30in-lb. Figure 1-9 12200 and 12300 Four Post Standard Rack Mounting 12200 Four Post Shallow-Depth Rack Installation In a shallow-depth rack, the distance between the front and back mounting posts is ~16" (400mm). Mounting rails for the 12200 are adjustable to accommodate racks with 14"-20" between mounting posts.
1–Installation 12200/12300 Installation • M6 screws Installation 1. Install the hat rails with mounting ears towards the port side of the switch. Fasten with three (3) #6-32 screws per rail. Torque screws to 8in-lb. Figure 1-10 12200 Hat Rails 2. Install six (6) cage nuts into the rack posts. Two cage nuts into posts on the front side of the rack and four cage nuts into posts in the rear of the rack. Note that the front of the rack is where the switch is installed.
1–Installation 12200/12300 Installation 3. Install two C-brackets in the rear of the rack. Fasten to the rack posts with four (4) M6 screws. Slide the switch from the front of the rack into the C-brackets and fasten to the front posts with two (2) M6 screws. Torque to 30in-lb.
1–Installation 12800-180 Installation 12800-180 Installation NOTE: The following procedures are for installing the switch using a fixed distance between the front and rear rack posts. Mounting Hardware Kit Contents: NOTE: The mounting kit contains all of the necessary parts for installing and mounting the switch into a 19" 4-post server rack with a distance between front and back posts of 719mm and 742mm.
1–Installation 12800-180 Installation 2. Install support rails in the rack and fasten with M6 screws. There are two (2) clip nuts and two (2) screws per post. Torque to 30in-lb. Figure 1-12 Support Rail Installation 3. Install four (4) flat brackets on the chassis. The brackets have two sets of holes, for ~3" and for ~4" extension beyond the rear of the chassis. For 719mm between rack rails, use the hole set for 3" extension.
1–Installation 12800-180 Installation rails, use the hole set for 4" extension. Fasten each bracket with #8 flat head screws. There are four (4) screws per bracket. Torque to 30in-lb. Figure 1-13 Flat Bracket Installation 4. Orient the chassis such that mounting flanges are in the front of the rack. Install the chassis in the rack.
1–Installation 12800-180 Installation WARNING!! To avoid injury, do not lift manually when fully loaded. The 12800-180, when fully-populated, weighs 270lbs (125kg). Use a mechanized lift only. For a manual lift, unload the product to minimize the weight (an empty chassis weighs 100lbs/45kg). Use a team of people appropriate to the weight of the product and in conjunction with applicable laws and guidelines. Figure 1-14 Mounting Flange Installation 5.
1–Installation 12800-180 Installation 6. Install four U brackets in the rear of the chassis. Fasten each U bracket to a flat bracket with #10 flat head screws. There are four screws per bracket. Fasten the U brackets to EIA rails with M6 screws. There are two screws per bracket. Torque all screws to 30in-lb. Figure 1-15 U Bracket Installation 7. If applicable, replace the door(s) on the rack.
1–Installation 12800-360 Standard Rack Installation 12800-360 Standard Rack Installation Mounting Hardware Kit Contents: NOTE: The mounting kit hardware contains all of the necessary parts for installing and mounting the switches into a rack. These kits are intended for use in cabinets with a depth ranging from 28 - 34 inches.
1–Installation 12800-360 Standard Rack Installation Overview The 12800-360 is the largest in the 12800-series of switches, capable of supporting up to 864 InfiniBand ports operating at QDR speed. It is packaged in a large, 29U (50.75 inch) chassis. As such, it is expected to utilize most of the available U-space within a rack.
1–Installation 12800-360 Standard Rack Installation Installation tasks NOTE: It is recommended that 12800-360 is installed into the rack at a 5U or 6U location. This will locate the chassis approximately 12” from the floor and will allow the chassis to be moved onto the support shelf by sliding off the pallet. Mark the rack and install clip nuts in the rack holes as shown on the diagram. There are 24 M6 clip nuts. 1. If applicable, remove the doors of the rack.
1–Installation 12800-360 Standard Rack Installation Assemble the Support Shelf Figure 1-18 Support Shelf Assembly 1. Attach 4 mounting brackets to the support shelf with M6 HEX screws. There are 4 screws per bracket. Torque screws to 36in-lb. 2. Attach 2 guide brackets to the support shelf with #10-32 screws. There are 2 screws per bracket 3. Remove 2 cable trough covers. Attach 2 cable troughs to the bottom of the support shelf with #10-32 screws. There are 4 screws per trough.
1–Installation 12800-360 Standard Rack Installation 5. Install the support shelf and side panels. Figure 1-19 Support Shelf and Side Assembly 6. Install the support shelf in the rack as shown from the front of the rack. Use M6 screws to fasten to the rack rails. There are 2 screws per rack rail. Torque screws to 36in-lb. 7. Install 4 side panels in the rack as shown from the front of the rack and fasten with M6 screws to the rack rails.
1–Installation 12800-360 Standard Rack Installation chassis is installed in a 5U or 6U space on top of the support shelf. NOTE:M6 nut clips should be pre-installed in corresponding locations on the rack rails before installing the support shelf and the side panels. 8. Assemble cable management hardware on top of the chassis. Figure 1-20 Top Chassis Cable Management Assembly 9. Attach 2 Top brackets to the top of the chassis. Use screws installed in the chassis cover. There are 5 screws per bracket. 10.
1–Installation 12800-360 Standard Rack Installation Install the Chassis in the Rack 1. Orient and position the chassis for installation in the rack WARNING!! To avoid injury, install the 12800-360 using a mechanized lift only. When fully-populated, the switch weighs 535lbs (244kg) (an empty chassis weighs 197lbs/90kg). 2. Orientation of the chassis on a pallet: The chassis has been packaged on sliding surfaces to facilitate installation in the rack by sliding off the pallet and onto the support shelf.
1–Installation 12800-360 Standard Rack Installation 3. Position the chassis on front on the rack: Use a pallet jack to move the chassis. Orient the chassis on the pallet in front of the rack as shown. The chassis rear should be facing the front of the rack. For installations in racks arranged in rows, the distance between adjacent rows of racks (i.e., the width on a cold aisle) should be greater than 36" to be able to move the chassis on a pallet through a cold aisle.
1–Installation 12800-360 Standard Rack Installation 4. Installing the chassis in the rack: Align the chassis with the rack. Raise the chassis using a pallet jack such that the bottom of the chassis is at or slightly higher than the top surface of the support shelf pre-installed in the rack. Lock the pallet jack wheels. Use a group of people to push the chassis from the front to slide it off the pallet and on the support shelf.
1–Installation 12800-360 Standard Rack Installation 5. Install from the front of the rack as shown. Push chassis into the rack until the rear of the chassis is against the Rear bracket. Figure 1-24 Chassis Installation 1-28 6. Install the chassis in the rack by sliding off the pallet and onto the support shelf. Install from the front of the rack as shown. Push chassis into the rack until the rear of the chassis is against the Rear bracket. 7.
1–Installation 12800-360 Standard Rack Installation Install the C-mounting brackets Figure 1-25 Chassis Installation 1. Install 2 C-brackets on the chassis. Slide C-brackets over Hat-rails pre-installed on the chassis. Fasten to the rack rails with M6 screws. Torque to 36in-lb. NOTE: M6 nut clips should be pre-installed in corresponding locations on the rack rails before installing the chassis in a rack.
1–Installation 12800-360 Standard Rack Installation Install the Front Mounting Bracket Figure 1-26 Front Mounting Bracket 1. Install the Front bracket and fasten to the Top bracket with #10-32 screws. There are 5 screws. Fasten the Front bracket to the rack rails with M6 screws. NOTE: M6 nut clips should be pre-installed in corresponding locations on the rack rails before installing Front bracket.
1–Installation Connect Equipment to the Ports and Power On the System Connect Equipment to the Ports and Power On the System NOTE: Before connecting equipment, it is important to understand the locations of the serial and Ethernet ports on the 12200, 12300 and 12800 series. For the 12200 and 12300, these are located on the switch IB port side. For the 12800 series, these are located on the Serial, Ethernet, Chassis EEPROM Board (SEEB) modules.
1–Installation Connect Equipment to the Ports and Power On the System 1. Connect a Category 5 or 6 (Cat 5/6) Ethernet cable to the RJ-45 connector(s) on the switch. Connect the other end of the Cat 5/6 to an OOB LAN workstation, another switch or a hub. 2. Connect the switch to IB-enabled host(s)/switch(es) using QDR QSFP IB cables, or to DDR host(s)/switch(es) using a QSFP-CX4 cable. NOTE: Make sure all cables latch securely into the corresponding port connectors.
1–Installation Connect Equipment to the Ports and Power On the System Figure 1-29 DC ON/OFF Switch 5. The switch, power supply, and fan LEDs light up.
1–Installation Bringing Up the System For the First Time Bringing Up the System For the First Time 12800-Series Management Module Protective Label Guidelines A management module installed in a 12800 system may have a protective label installed, as shown in Figure 1-30. This label protects the mechanical release latch (MRL) switch inside the management module from shock and vibration during shipping.
1–Installation Bringing Up the System For the First Time Figure 1-32 MRL Protective Label 3 3. After testing is complete at the staging area, reverse Steps 1 and 2 to prepare the system for shipment to the end-user site (see Figure 1-33). Figure 1-33 MRL Protective Label 4 User Site Installation After final installation of a 12800-series switch is completed at the end user site: 1. Disengage the thumb screw and partially rotate the lever as shown in Figure 1-34.
1–Installation Bringing Up the System For the First Time 2. Peel off the protective label. Re-engage the lever and tighten the thumb screw as shown in Figure 1-35. Figure 1-35 MRL Protective Label 6 Start-up Procedures 1. Power up the switch. 2. From its flash image on the management module, the switch begins its boot process. NOTE: If the DB9 port of the SEEB module or the RS232 port on the 12200/12300 is connected to a terminal emulation program, the user will be able to view the switch boot process.
1–Installation Bringing Up the System For the First Time 1. Determine the CLI access method (i.e., Telnet, SSH, or Serial).
1–Installation Bringing Up the System For the First Time NOTE: If using a serial port, skip to Step 6. Steps 2 through 5 are for those users accessing the switch via Telnet or SSH. For the 12800 series, make certain to connect to the SEEB serial port associated with the Master Management Module (MM). These are: • 12800-040: MM 201 • 12800-180: MM 211 • 12800-360: MM 227 2. Connect applicable serial cables to the RS-232/DB-9 ports of the switch. Connect the other end to a workstation.
1–Installation Bringing Up the System For the First Time where -h ipaddress is the new default gateway IP address in dotted decimal (i.e., xxx.xxx.xxx.xxx) format. 8. To to exit the CLI enter: logout Updating the Management Module IP Addresses in a Redundant Management Configuration (12800-180 and 12800-360) Each management module must have a unique IP address that is different than the chassis IP address of the switch. Therefore, a redundantly-managed switch will have multiple unique IP addresses.
1–Installation Bringing Up the System For the First Time 4. At the [boot]: prompt type the following: spineip Then press Enter. NOTE: This command changes the IP address for image1 and image2 on each module. 5. At the [boot]: prompt enter reboot, and press Enter. Upon reboot the IP address is changed. Repeat for the second Management Module.
1–Installation Component LEDs Component LEDs Management Module Figure 1-36 Management Module LEDs Module Status The status LED indicates one of the following conditions: • Steady Green - the module is operating normally. • Blinking Green - LED test state. • Off - module is in the removable state. Module Attention The Attention LED indicates one of the following conditions: • Off - the system functioning normally.
1–Installation Component LEDs Chassis Status and Attention The chassis status LED is Green when the system is functioning normally. The chassis status LED is Amber when one of the following conditions exists: • Any Fan Alarm is amber. • Any power supply AC OK LED is off. • Any power supply DC OK LED is off • Any spine module Attention LED is on, or it has been determined that a spine is not functioning (even if it is unable to light the LED).
1–Installation Component LEDs MRL Active The MRL Active LED is Green when mechanical release latch (MRL) thumbscrew is secured to the Serial, Ethernet, Chassis EEPROM Board (SEEB).
1–Installation Component LEDs Leaf Module Figure 1-38 Leaf Module LEDs IB Port LEDs Each module IB port has a Green IB link status LED that provide the following indications: • On - the logical link is up (port is in the Active state). • Off - the physical link is down (port is in the Down state). Module Status The status LED indicates one of the following conditions: • Steady Green - the module is operating normally. • Blinking Green - LED test state. • Off - module is in the removable state.
1–Installation Component LEDs • Off - the system functioning normally. • Steady Amber - the system requires some attention, which could indicate one of the following conditions: • The switch temperature is at a warning level on the module. • The switch silicon temperature is at a warning level (approximately 90 degrees C). • DC voltages on the board are slightly out of tolerance (12V Bulk, 5V, 3.3V and 1.8V are all monitored). • The module can no longer function properly.
1–Installation Component LEDs • The switch silicon temperature is at a warning level (approximately 90 degrees C). • DC voltages on the board are slightly out of tolerance (12V Bulk, 5V, 3.3V and 1.8V are all monitored). • The module can no longer function properly. The system will take the appropriate actions to ensure that no damage is done to its components. • Blinking Amber (once every four seconds) - LED test state.
1–Installation Component LEDs 12200 and 12300 Figure 1-41 12200 and 12300LEDs IB Port LEDs Each module IB port has a Green IB link status LED that provide the following indications: • On - the logical link is up (port is in the Active state). • Off - the physical link is down (port is in the Down state). Status The status LED indicates one of the following conditions: • Steady Green - the module is operating normally. • Blinking Green - LED test state. • Off - module is in the removable state.
1–Installation Component LEDs • DC voltages on the board are slightly out of tolerance (12V Bulk, 5V, 3.3V and 1.8V are all monitored). • The module can no longer function properly. The system will take the appropriate actions to ensure that no damage is done to its components. • Blinking Amber (once every four seconds) - LED test state. RJ45 LEDs The RJ45 connectors have two LEDs, Act and 100. The 100 LED is Green when a 100Mbps link is connected.
1–Installation Component LEDs • Green and Amber on indicates a possible problem, including: • The fan tray is not responding to commands for configuration and temperature-related operations. • A fan is not responding to commands for temperature and speed related operations. • The fan speed has fallen below the minimum allowed RPM for a fan. Power Supply LEDs Figure 1-43 12800 Power Supply LEDs Each power supply has three LEDs: DC OK, AC OK and Alarm. Following are the status definitions for each.
1–Installation Switch-Based QLogic Fabric Manager License Key Switch-Based QLogic Fabric Manager License Key If purchased, certain packages of the InfiniBand Fabric Suite entitle the user to the switch-based QLogic Fabric Manager. Refer to the licensing documentation that comes with the InfiniBand Fabric Suite for instructions on generating the license key.
1–Installation Switch-Based QLogic Fabric Manager License Key Procedures 1. Record the IFS serial number. 2. Go to the QLogic Feature Activation/License Key web site http://lk.qlogic.com. Figure 1-45 License Key Activation Center 1 3. Enter the InfiniBand Fabric Suite serial number. Click Continue.
1–Installation Switch-Based QLogic Fabric Manager License Key 4. Click Activate License Key and click Continue.
1–Installation Switch-Based QLogic Fabric Manager License Key 5. Enter your email address in the Email: and Confirm Email: text boxes. Click Continue.
1–Installation Switch-Based QLogic Fabric Manager License Key 6. Enter all applicable information. For the City: and/or the Zip/Postal Code entries, click on the flashlight hyperlinks. The following is displayed: Figure 1-49 License Key Activation Center 5 7. In the City: and Zip: text boxes, enter the applicable information and click Search. Alternatively, search through the list of cities, click the applicable radio button, then click Search.
1–Installation Switch-Based QLogic Fabric Manager License Key 8. If the information is correct, click Close.
1–Installation Switch-Based QLogic Fabric Manager License Key 9. Click Continue. The following screen is displayed: Figure 1-52 License Key Activation Center 8 10.
1–Installation Switch-Based QLogic Fabric Manager License Key NOTE:The FRU GUID can be found: On the label of each FRU. D000102-000 B Using the Chassis Viewer, the View FRU button for each applicable chassis or module FRU. For the 12200/12300 via the switch Command Line Interface (CLI), using the command showIBNodeDesc. For the 12800 series via the switch Command Line Interface (CLI), using the command fruInfo .
1–Installation Switch-Based QLogic Fabric Manager License Key 1-58 D000102-000 B
A QLogic 12000 Series Product Specifications Physical Specifications All products within the 12200, 12300 and 12800 Director series are designed to be installed in industry-standard 19-inch four-post server racks. Racks should conform to conventional standards. Use the American National Standards Institute (ANSI)/Electronic Industries Association (EIA) standard ANSI/EIA-310-D-92 and International Electrotechnical Commission (IEC) 297. These racks are commercially available in various depths.
A–QLogic 12000 Series Product Specifications Environmental Specifications Environmental Specifications • Operating temperature: 5° - 40°C at sea level, altitude derating 1°C per 300m to 2,400m • Non-operating temperature: -40°C to 65°C • Relative humidity (non-condensing): Operating 5% - 85%; Non-operating 5% - 90% 12200 and 12300 Cooling and Thermal Management: Cooling: Air cooled with a hot plug fan/power tray, three fans per tray, 40mm, 12VDC (12300) Four fans, no fan trays (12200) Front-
A–QLogic 12000 Series Product Specifications 12800 Series 12800 Series All 12800 series switches use the same fan tray modules -- intake and exhaust -and share the same thermal management attributes listed below. The quantity of fan tray modules used in each system is defined in the following table: Table A-2.
A–QLogic 12000 Series Product Specifications 12800 Series appropriate temperatures of major heat producing components. Monitoring is performed via a two wire I2C interface to each Fan Tray. Power Specifications All products within the 12800 series use a common switching power supply. System power attributes are shown in the table below. Power supplies are N+1 redundant and hot pluggable. NOTE: An AC power cord is required for each power supply. Refer to the table below. Table A-3.
A–QLogic 12000 Series Product Specifications 12800 Series Power Distribution Guidelines The following section details power distribution guidelines and recommendations for the QLogic 12800 series. The power supplies for the 12800 series has a maximum inlet current of 15amps @ 110volts and 6amps @ 220volts. Please observe power outlet, power strip and extension cable ratings.
A–QLogic 12000 Series Product Specifications 12800 Series Table A-4. AC Plug Types A-6 Region/Country Voltage Rating Plug Type North America 100-127 NEMA 5-20P North America 200-240 NEMA L6-20P North America 200-240 NEMA L15-30P Three phase AC Europe (Schuko) 200-240 CEE 7/7 Used in Austria, Belgium, Finland, France, Germany, Greece, Hungary, Indonesia, The Netherlands, Norway, Poland, Portugal, Russia, Spain, Sweden. International 200-240 IEC 309 3-wire (two-phase & earth).
A–QLogic 12000 Series Product Specifications 12800 Series D000102-000 B A-7
A–QLogic 12000 Series Product Specifications 12800 Series Notes A-8 D000102-000 B
B Safety and Regulatory Compliance Information This section provides regulatory compliance, safety and electromagnetic compatibility (EMC) information for the QLogic 12000 series products. Safety Information Statement 1: Disconnect Device - This unit may have more than one power cord. To reduce the risk of electrical shock, disconnect all power cords before servicing unit. Verklaring 1: Apparaat loskoppelen - Deze eenheid heeft mogelijk meer dan een stroomkabel.
B–Safety and Regulatory Compliance Information Safety Information Dichiarazione 1: Scollegare il dispositivo - L'unità potrebbe avere più di un cavo di alimentazione. Per ridurre il rischio di scosse elettriche, scollegare tutti i cavi di alimentazione prima di intervenire sull'unità. Erklæring 1: Frakobling av enheten - denne enheten kan ha mer enn én strømledning. For å redusere faren for elektrisk sjokk, må alle strømkablene trekkes ut før enheten vedlikeholdes.
B–Safety and Regulatory Compliance Information Safety Information Statement 2: Chassis Lifting - Use safe practices when lifting. NOTE: Use a team of people appropriate to the weight of each specified product and in conjunction with applicable guidelines. Whenever possible, use a mechanical lift. Verklaring 2: Chassis optillen - Volg de veiligheidsinstructies bij het optillen. ANMERKUNG: Gebruik genoeg mensen voor het gewicht van elk gespecificeerd product en hanteer de toepasselijke richtlijnen.
B–Safety and Regulatory Compliance Information Safety Information Erklæring 2: Løfting av kabinettet - utvis varsomhet ved løfting. MERK: Bruk flere personer til bæring, avhengig av vekten til hvert enkelt produkt og i samsvar med gjeldende retningslinjer. Bruk mekaniske løftemekanismer når mulig. Declaração 2: Levantar o chassi - Utilize práticas seguras ao levantar o chassi. AVISO: Utilize um grupo de pessoas adequado ao peso de cada produto especificado, em conjunto com as directivas aplicáveis.
B–Safety and Regulatory Compliance Information Safety Information 注： 请按照每个具体产品的重量来使用一定的人数，并遵照适当的说 明。可能的话，使用机械起重器。 ステートメント 2： シャーシの持ち上げ - シャーシを持ち上げる際は安全に配慮してください。 メモ : D000102-000 B 各製品の重量に見合った人数で、適切なガイドラインに従って 持ち上げてください。可能な場合は、リフト機を使用してくだ さい。 B-5
B–Safety and Regulatory Compliance Information Safety Information Statement 3: Energy Hazard - To reduce risk of electric shock, keep hands and fingers out of the power supply bays and backplane areas. Verklaring 3: Stroomgevaar - Reduceer het risico op een elektrische schok door handen en vingers weg te houden bij de voedingscompartimenten en de gebieden rond de centrale printplaat. Varoitus 3: Sähköiskun vaara.
B–Safety and Regulatory Compliance Information Safety Information Uttalande 3: Risk för elektrisk stöt. Reducera risken för elektrisk stöt genom att hålla händer och fingrar borta från strömförsörjningsfack och bakpanelsområden. Kijelentés 3: Áramütés veszélye – Az áramütés kockázatának csökkentése érdekében kezeit és ujjait tartsa távol a tápcsatlakozóktól és a hátsó területektol.
B–Safety and Regulatory Compliance Information Safety Information Statement 4: Laser Radiation - certain optical products may emit laser radiation. Removing covers could result in exposure to hazardous laser radiation. Radiation may be emitted from connectors or fiber optic cables. Verklaring 4: Laserstraling - bepaalde optische producten kunnen laserstraling verspreiden. Het verwijderen van dekplaten kan resulteren in blootstelling aan schadelijke laserstraling.
B–Safety and Regulatory Compliance Information Safety Information Declaración 4: Radiación de láser - Ciertos productos ópticos pueden emitir radiación de láser. Quitar las cubiertas podría resultar en la exposición peligrosa a radiación de láser. La radiación se puede emitir de conectores o cables de fibra óptica. Uttalande 4: Laserstrålning. Vissa optiska produkter kan utsända laserstrålning. Borttagning av skydd kan resultera i exponering för riskfylld laserstrålning.
B–Safety and Regulatory Compliance Information Safety Information Statement 5: No User Serviceable parts - Hazardous energy levels may be present inside power supplies and circuit card modules. Do not remove covers. Verklaring 5: Onderdelen die niet door de gebruiker mogen worden onderhouden - Er kunnen gevaarlijke energieniveaus aanwezig zijn binnen voedingen en printplaten. Verwijder in geen geval dekplaten. Varoitus 5: Ei osia, jotka käyttäjä voisi vaihtaa.
B–Safety and Regulatory Compliance Information Safety Information Uttalande 5: Inga delar kan underhållas av användaren. Farliga energinivåer kan finnas i strömförsörjningsenheter kretskortmoduler. Ta inte bort skydd. Kijelentés 5: A berendezés nem tartalmaz felhasználó által javítható alkatrészeket – Veszélyes energiaszint lehet a tápegységeken és az áramköri kártyamodulokon belül. Ne távolítsa el a burkolatokat.
B–Safety and Regulatory Compliance Information Safety Information Statement 6: Equipment Installation - Only qualified personnel should be allowed to install, remove or replace chassis or modules. Verklaring 6: Installatie apparatuur - Voor het installeren, verwijderen of vervangen van chassis of modules mag alleen gekwalificeerd personeel worden gebruikt. Varoitus 6: Laitteiston asentaminen. Vain pätevä asentaja saa asentaa, poistaa ja vaihtaa koteloita tai moduuleja.
B–Safety and Regulatory Compliance Information Safety Information Kijelentés 6: Berendezés telepítése – Kizárólag szakképzett személyzet számára megengedett a burkolat vagy a modulok telepítése, eltávolítása vagy cseréje. Инструкция 6: Установка оборудования – Установка, удаление и замена корпуса или модулей устройства должна производиться только квалифицированным техническим персоналом.
B–Safety and Regulatory Compliance Information Safety Information Statement 7: Adding or Replacing Modules - These modules are intended only for installation in QLogic 12000 base units. Always install blanks when removing an active module. They prevent exposure to energy hazards inside the unit, contain EMI, and maintain cooling air balance in the chassis. Verklaring 7: Toevoegen of vervangen van modules - deze modules zijn alleen bedoeld voor installatie in basiseenheden uit de QLogic 12000-reeks.
B–Safety and Regulatory Compliance Information Safety Information Erklæring 7: Tillegging eller utskifting av moduler - disse modulene skal kun installeres i baseenhetene på QLogic 12000-serien. Installer alltid tomme enheter når en aktiv modul fjernes. De forhindrer utsettelse for strømfare inni enheten, inneholder EMI og opprettholder kjølebalansen i kabinettet.
B–Safety and Regulatory Compliance Information Safety Information ステートメント 7： モジュールの追加または取替え - これらのモジュールは QLogic 12000 シリーズ MPFD ベースユニットへの取り付け専用です。アクティブなモジュールを取り除 く際は、常にダミーを取り付けてください。これはユニット内の危険なエネル ギーの露出を防止し、EMI を阻止、およびシャーシ内の空冷バランスを維持しま す。 B-16 D000102-000 B
B–Safety and Regulatory Compliance Information Safety Information D000102-000 B B-17
B–Safety and Regulatory Compliance Information Safety Information Notes B-18 D000102-000 B
C Serial Port Pinouts For those users making their own serial cables, follow the guidelines below.
C–Serial Port Pinouts Figure C-1 represents the RJ-11 connector located on the QLogic 12200 and12300. The only serial port signals required are: Tx, Rx and Ground. All other serial port signals are NOT used. Please see Table C-1 for a list of RJ45 (on Digi) to RJ11 cross-references. The cable should connect the three RJ45 signals (on the Digi) to the RJ11 connector. The signals for the T3 card located inside the switch and spine are included for reference only. Table C-1.
C–Serial Port Pinouts D000102-000 B C-3
C–Serial Port Pinouts Notes C-4 D000102-000 B
D FRU Replacement This section details replacement information for various QLogic 12000 components. For replacement parts, contact QLogic or an approved reseller. NOTE: If part of a standard operating procedure, add replacement identification tags to both the rack and the FRU hardware to ensure that the warranty is transferred to the replacement part(s). NOTE: If the FRU being replaced is in an active chassis (i.e, hot swapping), please replace the FRU within 2 minutes.
D–FRU Replacement QLogic 12300 3. Connect Ethernet and Serial cables. 4. Connect AC power. 5. If applicable, change the switch, gateway and subnet mask addresses to a new network address. 6. Cable all applicable IB ports. QLogic 12300 Chassis Replacement FRU part number:12300-BS01-9X Removal Procedures 1. Power down the switch by unplugging AC power. 2. Remove all applicable IB, Ethernet and Serial cables. Set these aside for reinstalling the replacement switch. 3.
D–FRU Replacement QLogic 12800-180 and 12800-360 2. While holding the finger tab, pull the module handle to disengage the unit from the switch. Figure D-1 .12300 Fan/Power Module Removal Replacement Procedures 1. Hold the unit by the handle and slide into the applicable slot until the finger tab clicks into place. QLogic 12800-180 and 12800-360 If the user needs to replace either a 12800-180 or 12800-360 chassis, the chassis will be delivered pre-installed in a standard rack.
D–FRU Replacement QLogic 12800-180 and 12800-360 D-4 3. Identify a transfer location. This is an area, if available, where the current chassis/rack and new replacement chassis/rack can be placed side by side. This area should also have space for the original switch components (i.e., leafs, spines, management modules, fan trays and power supplies) that need to be re-installed into the new chassis. 4. Remove the front and rear rack doors. Save these for the new chassis/rack. 5.
D–FRU Replacement QLogic 12800 Series 16. Reinstall any intra-rack cabling and additional hardware, customer racked devices, components that were previously removed to facilitate component swap and FRU replacement. 17. Check ALL power connections for proper seating. 18. Move replacement FRU rack to a location that enables full power connectivity and verify all power connections and components are operational. 19. Reinstall the side covers. 20.
D–FRU Replacement QLogic 12800 Series Removal Procedures 1. While holding the handle, push the release latch to the right Figure D-2 .12800 Fan Removal 2. D-6 Pull the fan by the handle until disengaged from the chassis.
D–FRU Replacement QLogic 12800 Series 3. Determine whether this is an intake or exhaust fan by checking the FRU label or noting the location of the open notch. Figure D-3 .12800 Intake and Exhaust Fans Replacement Procedures D000102-000 B 1. Slide the fan tray straight into the open slot until it engages with the backplane connector. 2. Make sure the fan is operating and the status LED is green.
D–FRU Replacement QLogic 12800 Series Power Supply Replacement FRU part number:12800-PS01-9X Removal Procedures 1. Push the release latch to release the arm. Figure D-4 .12800 Power Removal 2. Carefully pull the supply until it is disengaged from the chassis. Replacement Procedures D-8 1. Slide the power supply straight into the open slot until it engages with the backplane connector. 2. Make sure the supply is operating and the AC OK and DC OK LEDs are green.
D–FRU Replacement QLogic 12800 Series Leaf Module Replacement FRU part number: 18 Port Leaf: 12800-LF18-9X 24 Port Leaf: 12800-LF24-9X Removal Procedures NOTE: If the leaf module is in one of the chassis management slots, the mechanical release latch (MRL) must be moved in order to remove the leaf. To move the MRL, loosen the thumbscrew attached to the SEEB module, then slide the MRL to the left. This allows enough clearance for leaf release arm. Figure D-5 .
D–FRU Replacement QLogic 12800 Series 1. Pull the release arms down until the leaf module disengages from the backplane connector. Figure D-6 .12800 Leaf Removal 2. Carefully pull the module out of the chassis. Replacement Procedures D-10 1. Slide the module straight into the open slot until it engages with the backplane connector. 2. Push the arm up until they lock in place. 3. Make sure the module is operating and the Status LED is green.
D–FRU Replacement QLogic 12800 Series Spine Module Replacement FRU part number: Single Spine Module: 12800-SPSG01-9X Double Spine Module: 12800-SPDB01-9X Removal Procedures 1. Pull the release arms out until the spine module disengages from the backplane connector. Figure D-7 .12800 Spine Removal 2. Carefully pull the module out of the chassis. Replacement Procedures D000102-000 B 1. Slide the module straight into the open slot until it engages with the backplane connector. 2.
D–FRU Replacement QLogic 12800 Series Management Module Replacement FRU part number:12800-MM01-9X Removal Procedures 1. Loosen the thumbscrew until it releases from the faceplate. 2. Pull the release arms out until the management module disengages from the backplane connector. Figure D-8 .12800 Management Module Removal 3. Carefully pull the module out of the chassis. Replacement Procedures 1. Slide the module straight into the open slot until it engages with the backplane connector. 2.
D–FRU Replacement QLogic 12800 Series D000102-000 B D-13
D–FRU Replacement QLogic 12800 Series D-14 D000102-000 B
Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 Europe Headquarters QLogic (UK) LTD. Quatro House Lyon Way, Frimley Camberley Surrey, GU16 7ER UK www.qlogic.com +44 (0) 1276 804 670 © 2010 QLogic Corporation. Specifications are subject to change without notice. All rights reserved worldwide. QLogic and the QLogic logo are registered trademarks of QLogic Corporation.
