User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
7 – SANsurfer iSCSI/FC Router Manager
Wizards
FI0054601-00 C 7-87
A
The FC and GigE Port Selection dialog box prompts you to select an
FC-GigE port pair, as shown in Figure 7-89.
Figure 7-89 FCIP Route Add Wizard—Port Selection Dialog Box
2. Select the FC-GigE Port pair. The corresponding parameter options become
available.
3. If desired, configure the following port route/parameters:
FCIP Interfaces FC & GE – Provides a drop-down box you can use to
enable or disable the FCIP route. Disabling the route places the FC
and GE ports in a down state. It still retains all route configuration
parameters.
GigE Port Programmed Link Rate – Provides a drop-down box you
can use select one of four options for the GigE link rate: auto, 10, 100,
or 1000. The default link rate is auto.
Link Rate Mode – Provides a drop-down box you can use select one
of three options for the link rate mode: auto, half duplex, or full duplex.
This dialog box is available only when the GigE link rate is set to
something other than auto.
GigE Port Flow Control – Provides a drop-down box you can use to
enable or disable GigE port flow control. The default is enabled. This
dialog box is available only when the GigE link rate is set to something
other than auto.
4. After selecting a port pair and setting GE port parameters, click Next to
continue or click Cancel to quit the wizard.