User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
7 – SANsurfer iSCSI/FC Router Manager
Wizards
7-90 FI0054601-00 C
S
VLAN Priority – Provides a drop-down box that contains eight options
for the VLAN priority: any number between 0–7. This dialog box is
available only when VLAN is enabled.
8. After setting the TCP/IP parameters, click Next to continue or click Cancel
to quit the wizard.
The FCIP Options dialog box requests entry of FCIP parameters, as shown
in Figure 7-92.
Figure 7-92 FCIP Route Add Wizard—FCIP Options Dialog Box
9. Configure any of the following parameters:
FCIP Timestamp – Provides a drop-down box you can use to enable
or disable FCIP timestamps. The default is enabled.
Error Detect Timeout – Provides a drop-down box you can use to
select one of five options for the error detect timeout: any number
between 1 to 5 seconds. The default is one second.
Resource Allocate Timeout – Provides a drop-down box you can use
to select one of five options for the resource allocate timeout: any
number between 1 to 5 seconds. The default is one second.
FCIP SW Compression – Provides a drop-down box you can use to
enable or disable FCIP compression. The default is disabled.
Bandwidth (Mbit/sec) – Provides a text field in which you can enter
the maximum bandwidth (in megabits per second) used by the GigE
port during transmits. The range of values supported is 1 to 1000
megabits per second. This setting allows you to limit the bandwidth