User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
A – Command Reference
Commands
A-10 FI0054601-00 C
S
FcipRoute Command
The FCIP route command provides for configuring a new FCIP route and
modifying or deleting an existing FCIP route. Each FCIP route requires a
dedicated FC and Gigabit Ethernet port. Configuring an FCIP route, specifying an
FC and GE port pair, take precedence over any previous configuration for the port
pair (FC/GE). This removes the previous configuration of the port pair.
Authority Admin session.
Syntax fciproute
add
mod
rm
Keywords add
The FCIP route add command configures a new FCIP route.
modify
The FCIP route modify command modifies an existing FCIP route.
remove
The FCIP route remove command removes an existing FCIP route.
Examples FCIP route add command example:
QRouter (admin) #> fciproute add
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both GE
ports.
Configuring FCIP Route: 1
---------------------------
FCIP Interfaces FC & GE (0=Enable, 1=Disable) [Enabled ]
FC Port (1=FC1, 2=FC2, ...) [FC1 ]
GE Port (1=GE1, 2=GE2, ...) [GE1 ]
IP Address (IPv4 or IPv6; 0=IPv6 Link Local) [0.0.0.0 ] 0
Selected IPv6 Link Local Address: fe80::2c0:ddff:fe0c:8be2