User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
A – Command Reference
Commands
A-20 FI0054601-00 C
S
Localmap Command
The localmap command maps a locally-connected initiator device to a
locally-connected target device. The initiator and target are not on the same FC
port.
Authority Admin session
Syntax localmap
add
rm
Keywords add
Add local initiator to target mapping.
rm
Remove local initiator to target mapping.
Examples Localmap add command example with FC port query:
QRouter (admin) #> localmap add
The following wizard will query for attributes before persisting and
activating the updated mapping in the system configuration. If you
wish to terminate this wizard before reaching the end of the list
press 'q' or 'Q' and the ENTER key to do so.
Index (WWNN,WWPN/iSCSI Name)
----- ----------------------
0 50:06:01:60:b0:22:0c:d1,50:06:01:68:30:22:0c:d1
1 iqn.1991-05.com.microsoft:qlogic-09sd5i4l
Please select an Initiator from the list above ('q' to quit) : 1
Index (WWNN,WWPN/iSCSI Name)
----- ----------------------
0 20:00:00:20:37:fd:9c:f7,22:00:00:20:37:fd:9c:f7
1 50:06:01:60:b0:22:0c:d1,50:06:01:68:30:22:0c:d1
2 20:00:00:20:37:fd:8a:b0,22:00:00:20:37:fd:8a:b0
3 20:00:00:20:37:fd:8b:ab,22:00:00:20:37:fd:8b:ab
Please select a Target from the list above ('q' to quit) : 3
iSCSI port used to access the Initiator (1=GE1, 2=GE2, ...) : 2
FC port used to access the Target (1=FC1, 2=FC2, ...) : 1
The selected initiator has not been presented on the port that was
selected to access the target. The following steps in the wizard will
now setup the initiator so that it is presented on the port that will
be used to access the target. A default name for the presented