User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
A – Command Reference
Commands
A-42 FI0054601-00 C
S
Set iSCSI Command
Configures an iSCSI port.
Authority Admin session
Syntax set iscsi [port_num]
Keywords [port_num]
The number of the iSCSI port to be configured.
Examples Set iSCSI command example:
QRouter (admin) #> set iscsi 1
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both
ports.
Configuring iSCSI Port: 1
---------------------------
Port Status (0=Enable, 1=Disable) [Enabled ]
IP Address [0.0.0.0 ]
Subnet Mask [0.0.0.0 ]
Gateway IP Address [0.0.0.0 ]
Target TCP Port No. (Min=1024, Max=65535) [3260 ]
MTU Size (0=Normal, 1=Jumbo, 2=Other) [Normal ]
Window Size (0=8KB, 1=16KB, 2=32KB) [32768 ]
Window Scaling (0=Enable, 1=Disable) [Enabled ]
Window Scaling Factor (Min=0, Max=5) [1 ]
Port Speed (0=Auto, 1=100Mb, 2=1Gb) [Auto ]
Header Digests (0=Enable, 1=Disable) [Enabled ]
Data Digests (0=Enable, 1=Disable) [Enabled ]
VLAN (0=Enable, 1=Disable) [Disabled ]
IPv6 Address 1 [:: ]
2001::1234
IPv6 Address 2 [:: ]
IPv6 Default Router [:: ]