User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
B – Log Messages
Error Log Messages
B-14 FI0054601-00 C
S
98 Unable to create an object for the target device: exceeded the maximum
number of target devices.
100 Unable to create an object for the target node: exceeded the maximum
number of target devices.
107 Memory unavailable for LUN object.
117 Unable to create an object for initiator object: exceeded the maximum number
of initiators.
136 Process control block status indicates that a PCI error occurred during a target
operation.
146 Process control block status indicates that a DMA error occurred during an
initiator operation.
147 Process control block status indicates that a transport error (protocol)
occurred during an initiator operation.
151 Process control block status indicates that a data overrun error occurred
during an initiator operation.
274 iSCSI login failed between receipt of PDU and request for the data segment.
278 iSCSI login failed due to unsupported version number in received login PDU.
297 iSCSI Login PDU contains invalid initiator name. The format and character
set used to form the initiator name is invalid.
305 iSCSI target login was attempted to a portal (iSCSI1 or iSCSI2) on which the
target is not presented.
307 iSCSI Login PDU received for a target with a target name unknown to the
router.
308 iSCSI Login PDU received without a target name for a normal session.
310 iSCSI Login PDU received without an initiator name key/value.
312 iSCSI Login PDU received with an incorrect initiator task tag for a session
which is partially logged in. This would occur if a login PDU other than the
initial login PDU used an initiator task tag which was different than the initiator
task tag provided in the initial login PDU.
323 iSCSI Login PDU was received with a TSIH out of range. This would occur if
the iSCSI initiator attempting the login failed to used the TSIH value provided
in the Target Login Response PDU (router is target) in subsequent login PDUs.