User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
4 – Installation
SANbox 6142 Router Installation
4-10 FI0054601-00 C
S
Configure the Router
You can configure the router using the SANsurfer iSCSI/FC Router Manager
application or the command line interface (CLI).
The SANsurfer Router Manager provides a Configuration Wizard you can use to
configure the GE ports. If either of the router’s GE ports have not been configured
(IP address is 0.0.0.0), the Configuration Wizard starts automatically when the
SANsurfer first connects with the router. The system uses the information
collected in Table 4-2.
To configure the router using the command line interface:
1. Open a command window according to the type of workstation and
connection:
Ethernet (all platforms) – Open a telnet session with the default router
IP address and log in to the router with the default account name and
password (guest/password).
telnet 10.0.0.1
username – guest
password – ********
Serial – On Windows, open the HyperTerminal application. The next
few steps may vary according to the version of Windows you use.
a. From the Windows Start menu, select
Programs>Accessories>HyperTerminal>HyperTerminal.
b. Select the connection you created earlier and click OK.
Serial – On Linux, open a command window and enter the following
command:
minicom
2. Open an admin session and enter the commands to setup both iSCSI ports
and the management interface. See Appendix A for command descriptions.
QRouter #> admin start
Password – ******
QRouter (admin) #> set mgmt
………………………
QRouter (admin) #> set iscsi 1
………………………
QRouter (admin) #> set iscsi 2
………………………