User guide

AIR CIRCULATOR; FAN HEAD

MODELS: 24ACH, 30ACH, 24ACH-0,

30ACH-0, MACH-24, MACH-30,

HD24-H, HD20-H & AF30-H

READ AND SAVE THESE INSTRUCTIONS

WARNING: To reduce the risk of fire and shock, do not use this fan with a solid state speed

control device.

WARNING: To reduce the risk of fire, electric shock, or injury to person, observe the following:

a.)Use this unit only in the manner intended by the manufacturer. If you have questions,

contact the manufacturer.

b.)Before servicing or cleaning unit, switch power off at service panel and lock the service

disconnection means to prevent power from being switched on accidentally. When the serv-

ice disconnection means cannot be locked, securely fasten a prominent warning device,

such as a tag to the service panel.

c.)Installation work and electrical wiring must be done by qualified person(s) in accordance

with all applicable codes and standards, including fire rated construction.

d.)When cutting or drilling into walls or ceilings, do not damage electrical wiring and other

hidden utilities.

CAUTION: Oscillating units must be disengaged prior to moving to prevent damage to the

gear mechanism.

CAUTION: DO NOT install oscillating fans upside down as this may allow the fan to fall or

become permanently damaged. Mount only as shown in this manual with the fan head

on top of the bracket.

CAUTION: DO NOT use an extension cord

DO NOT oil motor; motor bearings are permanently lubricated

DO NOT put foreign objects through fan guard into blade

CAUTION: DO NOT move fan while blade is moving. Always turn fan off and let blade

stop before attempting to move. DO NOT use blade guard to move fan

WARNING: To reduce the risk of fire, electric shock, and injury to persons, this Marley

Engineered Products fan must be installed with Marley Engineered Products Mounts that

are accordingly marked on their cartons to indicate the suitability with this model. Other

mounts cannot be substituted. The approved Marley Engineered Products mounts for the

above models are as follows:

• 2430PB Pedestal Mount = 24ACH, 30ACH, 24ACH-0, 30ACH-O, MACH-24, MACH-30

• 2430W-G Wall Mount = 24ACH, 30ACH, 24ACH-0, 30ACH-0, MACH-24, MACH-30

• 2430I I-Beam Mount =24ACH, 30ACH, MACH-24, MACH-30

• 2430C Ceiling Mount = 24ACH, 30ACH, MACH-24, MACH30

• 2430S Suspension Mount = 24ACH, 30 ACH, MACH-24, MACH-30

• HDM-PB Pedestal mount = HD24-H, HD30-H, AF30-H

• HDY-W-Y Wall Mounts = HD24-H, HD30-H, AF30-H

• HDM-I I-Beam Mounts = HD24-H, HD30-H, AF30-H

• HDM-C Ceiling Mounts = HD24-H, HD30-H, AF30-H

PAGE 1
AIR CIRCULATOR; FAN HEAD MODELS: 24ACH, 30ACH, 24ACH-0, 30ACH-0, MACH-24, MACH-30, HD24-H, HD20-H & AF30-H READ AND SAVE THESE INSTRUCTIONS WARNING: To reduce the risk of fire and shock, do not use this fan with a solid state speed control device. WARNING: To reduce the risk of fire, electric shock, or injury to person, observe the following: a.)Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. b.
PAGE 2
OPERATING INSTRUCTIONS: Marley Engineered Products Air Circulators can be used alone, or in conjunction with air conditioning unit to circulate cool air or to force it into other areas. This Marley Engineered Products Air Circulator can also be used in the winter to force the warm air trapped near the ceiling, down toward the floor level for warming comfort. NOTE: If your fan is experiencing vibration problems, please refer to the re-tracking instructions shown below. CLEANING: Disconnect power to the unit.