User Manual

The Qsync app can recover the
Qsync hardware. Simply tap
______ .
If the Troubleshooting section does
not resolve an issue, open the app
and tap ___________ .
1
Symptom Problem Solution
I added a group, but it
does not show up in My
Groups list.
Poor network
connection.
Exit out of the app by tapping __ . Re-open the app. If this
has not xed the problem, your device could be having WiFi
connectivity issues. Check for a WiFi connection or try to
move closer to the WiFi router.
I deleted a group, but
it still shows up in My
Groups list.
Poor network
connection.
Exit out of the app by tapping __ . Re-open the app. If this
has not xed the problem, your device could be having WiFi
connectivity issues. Check for a WiFi connection or try to
move closer to the WiFi router.
I tried to change the
settings of a group, but
nothing happened.
Your device did not
create that group.
You can only modify or delete groups that were created by
the same device. In other words, creating a group on a
Smart Phone would only allow that particular Smart Phone to
modify or delete that group. No other device has permission
to do so.
Qsync Recovery Console
If you still experience difculties, please call
toll-free 1-877-849-6070.
Troubleshooting
Set a Passcode
Tap the blue arrow on the
Qsync you wish to protect.
Swipe the Passcode slider
to “ON”.
Enter a 4 digit pass code and
tap _______.
2
1
2
9000136 US 8.26.15
FCC
Warning: Changes or modifications to this device not expressly approved by QMotion Advanced Shading Systems could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener-
ates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
This radio transmitter, model QSYNC-433FM, has been approved by Industry Canada to operate with types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s’il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible
maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l’exploitation de l’émetteur.
Approved antenna: QMotion Advanced Shading Systems P/N 6500034, 433MHz RP-SMA swivel antenna, 50Ω, 2.5dBi
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.