AcousticPerformance (AP) User Guide AP-5102 — 10" Two-way Trapezoidal Loudspeaker with 105˚axisymmetric coverage AP-5122 — 12" Two-way Trapezoidal Loudspeaker with 90˚axisymmetric coverage AP-5152 — 15" Two-way Trapezoidal Loudspeaker with 75˚axisymmetric coverage AP-5122m — 12" Two-way Multi-purpose Loudspeaker with 90˚axisymmetric coverage EXPLANATION OF SYMBOLS The term “WARNING!” indicates instructions regarding personal safety.
Warranty (USA only; other countries, see your dealer or distributor) QSC Audio Products 3 Year Limited Warranty QSC Audio Products, LLC (”QSC”) guarantees its products to be free from defective material and/or workmanship and will replace defective parts and repair malfunctioning products under this warranty when the defect occurs under normal installation and use, provided the unit is returned to our factory, one of our authorized service stations or an authorized QSC International Distributor via pre-paid
Shock Loading When a load is either moved or stopped, its static weight is magnified. Sudden movements can magnify the static weight several times. This magnification of static weight is called "shock loading". Shock loading poses a danger to equipment and workers. The effects of shock loading can be instantaneous, or may remain undetected unless the equipment is visually damaged. Proper preparation for shock loading requires careful planning and knowledge of equipment, suspension, and lifting practices.
Using Yoke Mounts M10 Cap Screw Split Washer Washer AcousticPerformance Loudspeakers can be installed using a yoke mount attached to the M10 Integrated Suspension Points. A 6 mm hex key is required. • Model AP-5102 (10") uses the AP-YM10 Yoke Mount Hex Plug Pads • Model AP-5122 (12") uses the AP-YM12 Yoke Mount • Model AP-5122m (12" multi-purpose) uses the AP-YM12m Yoke Mount NOTE: The AP-5122m mounts perpendicular to the yoke. Refer to Figure 2.
Connections AcousticPerformance Loudspeaker are capable of switching between Passive and Bi-amp mode. Look at the Setting ports to determine the current mode. Yellow in the Setting port indicates the current mode. Refer to Figure 3 and Figure 4 NOTE: The default mode, from the factory, is the passive crossover network.
Wiring the AcousticPerformance Loudspeaker WARNING!: Make sure the amplifiers are turned off, and disconnected from the power source, or the loudspeaker wiring is not connected to the amplifiers. Refer to Figure 7, Figure 8, and Figure 9. The pin numbers for the NL4 connector correspond to the pin numbers on the barrier strip. Model AP-5122m utilizes NL4 connectors only.
Specifications AP-5102 AP-5122 AP-5152 AP-5122m 60 Hz —18 kHz 48 Hz — 18 kHz 44 Hz — 18 kHz 55 Hz — 18 kHz Power Capacity (Continuous) Passive Bi-amp HF Bi-amp LF 54 V / 450 W 25 V / 80 W 54 V / 450 W 60 V / 550 W 25 V / 80 W 60 V / 550 W 65 V / 650 W 25 V / 80 W 65 V / 650 W 60 V / 550 W 25 V / 80 W 60 V / 550 W Nominal Sensitivity 2 94 dB, 1 W @1 m 95 dB, 1 W @1 m 96 dB, 1 W @1 m 95 dB, 1 W @1 m Nominal Coverage Angle (Axisymmetric) 105˚ 90˚ 75˚ 90˚ Directivity Factor (Q) 4.
Mailing Address: QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA Telephone Numbers: Main Number: (714) 754-6175 Sales & Marketing: (714) 957-7100 or toll free (USA only) (800) 854-4079 Customer Service: (714) 957-7150 or toll free (USA only) (800) 772-2834 Facsimile Numbers: Sales & Marketing FAX: (714) 754-6174 Customer Service FAX: (714) 754-6173 World Wide Web: www.qscaudio.com E-mail: info@qscaudio.com service@qscaudio.com © 2013 QSC Audio Products, LLC.
AcousticPerformance (AP) Guía del usuario AP-5102 — Altavoz trapezoidal bidireccional de 10" con cobertura axisimétrica de 105˚ AP-5122 — Altavoz trapezoidal bidireccional de 12" con cobertura axisimétrica de 90˚ AP-5152 — Altavoz trapezoidal bidireccional de 15" con cobertura axisimétrica de 75˚ AP-5122m — Altavoz polivalente bidireccional de 12" con cobertura axisimétrica de 90˚ EXPLICACIÓN DE LOS SÍMBOLOS El término “¡ADVERTENCIA!” indica instrucciones con respecto a la seguridad personal.
Garantía (sólo para EE.UU.
• ¡Nunca dé nada por sentado! Los puntos de conexión para la suspensión suministrados por el propietario o un tercero pueden no resultar adecuados para suspender las cargas. • Antes de izar, inspeccione siempre todos los componentes (cajas, soportes de suspensión, pasadores, bastidores, pernos, tuercas, eslingas, grilletes, etc.) en busca de grietas, desgaste, deformación, corrosión, o piezas faltantes, sueltas o dañadas que pudieran reducir la fuerza del conjunto.
Uso de los montajes de horquilla M10-Kopfschraube Federring Unterlegscheibe Los altavoces AcousticPerformance pueden instalarse usando un montaje de horquilla acoplado a los puntos de suspensión M10 integrados. Se necesita una llave hexagonal de 6 mm.
Conexiones El altavoz AcousticPerformance puede cambiar entre el modo Pasivo y el modo Bi-Amp. Mire el puerto de configuración (SETTING) para determinar el modo actual. El color amarillo en dicho puerto indica el modo actual. Consulte la Figura 3 y la Figura 4. NOTA: El modo predeterminado de fábrica es el de red de cruce pasivo.
Cableado del altavoz AcousticPerformance ¡ADVERTENCIA!: Compruebe que los amplificadores estén apagados y desconectados de la fuente de alimentación, o que los cables del altavoz no estén conectados a los amplificadores. Consulte la Figura 7, la Figura 8 y la Figura 9. Los números de las patillas del conector NL4 se corresponden con los números de las patillas en la tira de barrera. El modelo AP-5122m utiliza conectores NL4 solamente.
Especificaciones AP-5102 AP-5122 AP-5152 AP-5122m Respuesta de frecuencias (-10 dB): 60 Hz – 18 kHz 48 Hz – 18 kHz 44 Hz – 18 kHz 55 Hz – 18 kHz Capacidad de potencia 1 (continua) Pasivo Bi-Amp HF Bi-Amp LF 54 V / 450 W 25 V / 80 W 54 V / 450 W 60 V / 550 W 25 V / 80 W 60 V / 550 W 65 V / 650 W 25 V / 80 W 65 V / 650 W 60 V / 550 W 25 V / 80 W 60 V / 550 W Sensibilidad nominal 2 94 dB, 1 W a 1 m 95 dB, 1 W a 1 m 96 dB, 1 W a 1 m 95 dB, 1 W a 1 m Ángulo de cobertura nominal (axiximétrica)
Dirección postal: QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 EE.UU. Números de teléfono: Número principal: (714) 754-6175 Ventas y Comercialización: (714) 957-7100 o línea sin costo (sólo EE.UU.) (800) 854-4079 Servicio al Cliente: (714) 957-7150 o línea sin costo (sólo en EE.UU.) (800) 772-2834 Números de fax: Ventas y Comercialización FAX: (714) 754-6174 Servicio al Cliente FAX: (714) 754-6173 World Wide Web: www.qscaudio.com Dirección electrónica: info@qscaudio.
AcousticPerformance (AP) Guide de l'utilisateur AP-5102 — Haut-parleur trapézoïdal bidirectionnel 10" avec couverture axisymétrique de 105˚ AP-5122 — Haut-parleur trapézoïdal bidirectionnel 12" avec couverture axisymétrique de 90˚ AP-5152 — Haut-parleur trapézoïdal bidirectionnel 15" avec couverture axisymétrique de 75˚ AP-5122m — Haut-parleur multifonction bidirectionnel 12" avec couverture axisymétrique de 90˚ EXPLICATION DES SYMBOLES La mention « AVERTISSEMENT ! » indique des instructions concernant la
Garantie (États-Unis seulement ; dans les autres pays, consulter le revendeur ou le distributeur) QSC Audio Products – Garantie limitée de 3 ans QSC Audio Products, LLC (« QSC ») garantit que ses produits sont dépourvus de tout vice de fabrication et/ou de matériel et remplacera les pièces défectueuses et réparera les produits qui fonctionnent mal dans le cadre de cette garantie si le défaut survient dans des conditions normales d'installation et d'utilisation – à condition que l'appareil soit retourné à l'
Choc au chargement Lorsqu'une charge est déplacée ou arrêtée, son poids statique est amplifié. Des mouvements brusques peuvent amplifier le poids statique d'un facteur supérieur à 1. Cette amplification de la masse statique porte le nom de « charge dynamique ». Le choc au chargement présente un danger pour l'équipement et les travailleurs. Les effets de la charge dynamique peuvent être instantanés ou passer inaperçus, sauf endommagement visible de l'équipement.
Utilisation des supports à berceau Vis à chapeau M10 Rondelle fendue Rondelle Les haut-parleurs AcousticPerformance peuvent être installés à l'aide d'un support à berceau attaché aux points de suspension intégrés M10. Une clé à six pans de 6 mm est requise.
Branchements Le haut-parleur AcousticPerformance est capable de permuter entre les modes Passif (Passive) et Bi-ampli (Bi-amp). Vérifier les ports Setting pour déterminer le mode actuel. Le voyant jaune dans le port Setting indique le mode actuel. Voir Illustration 3 et Illustration 4. REMARQUE : Le mode par défaut, à la sortie de l'usine, est le réseau de filtre passif.
Câblage du haut-parleur AcousticPerformance AVERTISSEMENT ! : S'assurer que les amplificateurs sont hors tension et débranchés de l'alimentation, ou que le câblage n'est pas branché sur les amplificateurs. Voir Illustration 7, Illustration 8 et Illustration 9. Les numéros de broche pour le connecteur NL4 correspondent aux numéros de broche sur la barrette de connexion. Le modèle AP-5122m utilise uniquement des connecteurs NL4.
Caractéristiques techniques AP-5102 AP-5122 AP-5152 AP-5122m 60 Hz — 18 kHz 48 Hz — 18 kHz 44 Hz — 18 kHz 55 Hz — 18 kHz Capacité de puissance (continue) Passive Bi-amp HF Bi-amp LF 54 V / 450 W 25 V / 80 W 54 V / 450 W 60 V / 550 W 25 V / 80 W 60 V / 550 W 65 V / 650 W 25 V / 80 W 65 V / 650 W 60 V / 550 W 25 V / 80 W 60 V / 550 W Sensibilité nominale 2 94 dB, 1 W à 1 m 95 dB, 1 W à 1 m 96 dB, 1 W à 1 m 95 dB, 1 W à 1 m Angle de couverture nominal (axisymétrique) 105˚ 90˚ 75˚ 90˚ Fac
Adresse : QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468, États-Unis Téléphone : Standard : (714) 754-6175 Ventes & Marketing : (714) 957-7100 ou numéro vert (États-Unis seulement) (800) 854-4079 Service clientèle : (714) 957-7150 ou numéro vert (États-Unis seulement) (800) 772-2834 Télécopieur : Fax Ventes & Marketing : (714) 754-6174 Fax Service clientèle : (714) 754-6173 Site Web : www.qscaudio.com E-mail : info@qscaudio.com service@qscaudio.
AcousticPerformance (AP) Bedienungsanleitung AP-5102 – Trapezförmiger Zweiweglautsprecher, 10 Zoll, mit achsensymmetrischem 105˚-Abstrahlwinkel AP-5122 – Trapezförmiger Zweiweglautsprecher, 12 Zoll, mit achsensymmetrischem 90˚-Abstrahlwinkel AP-5152 – Trapezförmiger Zweiweglautsprecher, 15 Zoll, mit achsensymmetrischem 75˚-Abstrahlwinkel AP-5122m – Zweiweg-Mehrzwecklautsprecher, 12 Zoll, mit achsensymmetrischem 90˚-Abstrahlwinkel ERLÄUTERUNG DER SYMBOLE Der Begriff ACHTUNG! kennzeichnet Anweisungen, die di
Garantie (nur für die USA; wenden Sie sich zwecks Garantieinformationen für andere Länder an Ihren Händler oder Vertriebshändler) Beschränkte Dreijahresgarantie durch QSC Audio Products QSC Audio Products, LLC („QSC“) gewährleistet, dass seine Produkte keine Material- und/oder Ausführungsfehler aufweisen, und QSC verpflichtet sich zum Ersatz defekter Teile und zur Reparatur funktionsgestörter Produkte gemäß dieser Garantie, wenn dieser Fehler bei einer normalen Installation und unter normalen Gebrauchsbedin
• Annahmen können sich als falsch erweisen, weshalb Sie nur von gesicherten Kenntnissen ausgehen dürfen! Vom Besitzer oder anderen bereitgestellte Aufhänge-Befestigungspunkte reichen für das Aufhängen der Lasten möglicherweise nicht aus. • Inspizieren Sie vor dem Heben irgendwelcher Komponenten (Gehäuse, Aufhängungshalterungen, Stifte, Rahmen, Schrauben, Muttern, Schlingen, Schäkel usw.) diese auf Risse bzw.
Gebrauch von Jochhalterungen M10-Kopfschraube Federring Unterlegscheibe AcousticPerformance Lautsprecher können mit einer an den integrierten M10-Aufhängepunkten befestigten Jochhalterung montiert werden. Dafür wird ein 6-mm-Sechskantschlüssel benötigt. Sechskantstopfen Polsterscheiben • Das Modell AP-5102 (10") verwendet die Jochhalterung AP-YM10. • Das Modell AP-5122 (12") verwendet die Jochhalterung AP-YM12. • Das Modell AP-5122m (12"/Mehrzweck) verwendet die Jochhalterung AP-YM12m.
Verbindungen Bei AcousticPerformance Lautsprechern kann zwischen dem Passiv- und Bi-Amp-Modus umgeschaltet werden. Ein Blick auf die Einstellungsanschlüsse lässt den jeweils eingestellten Modus erkennen. Eine gelbe Markierung im Einstellungsanschluss zeigt den aktuellen Modus an. Siehe Abbildung 3 und Abbildung 4. HINWEIS: Der werkseitig voreingestellte Modus ist das passive Crossover-Netzwerk.
Verdrahten des AcousticPerformance Lautsprechers ACHTUNG! Stellen Sie sicher, dass die Verstärker ausgeschaltet und vom Netz getrennt sind bzw. dass die Lautsprecherkabel nicht an den Verstärkern angeschlossen sind. Siehe Abbildung 7, Abbildung 8 und Abbildung 9. Die Zahl der Anschlusspole für den NL4-Verbinder entspricht der Zahl der Anschlusspole auf dem Barrier-Strip. Im Modell AP-5122m werden nur NL4-Verbinder verwendet. Verdrahtung Modell Größe Verdrahtung Max.
Technische Daten AP-5102 AP-5122 AP-5152 AP-5122m 60 Hz – 18 kHz 48 Hz – 18 kHz 44 Hz – 18 kHz 55 Hz – 18 kHz Leistungskapazität (Dauerleistung) Passiv Bi-Amp HF Bi-Amp NF 54 V / 450 W 25 V / 80 W 54 V / 450 W 60 V / 550 W 25 V / 80 W 60 V / 550 W 65 V / 650 W 25 V / 80 W 65 V / 650 W 60 V / 550 W 25 V / 80 W 60 V / 550 W Nominelle Empfindlichkeit 2 94 dB, 1 W bei 1 m 95 dB, 1 W bei 1 m 96 dB, 1 W bei 1 m 95 dB, 1 W bei 1 m Nomineller Abstrahlwinkel (achsensymmetrisch) 105˚ 90˚ 75˚ 90˚
Adresse: QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA Telefonnummern: Zentrale: +1 (714) 754-6175 Verkauf und Marketing: +1 (714) 957-7100 oder gebührenfrei (nur in den USA) +1 (800) 854-4079 Kundendienst: +1 (714) 957-7150 oder gebührenfrei (nur in den USA) +1 (800) 772-2834 Fax-Nummern: Verkauf und Marketing - Fax: +1 (714) 754-6174 Kundendienst - Fax: (714) 754-6173 Internet: www.qscaudio.com E-Mail: info@qscaudio.com service@qscaudio.
AcousticPerformance (AP) 用户指南 AP-5102 — 10" 双向梯形扬声器,轴对称覆盖角度为 105° AP-5122 — 12" 双向梯形扬声器,轴对称覆盖角度为 90° AP-5152 — 15" 双向梯形扬声器,轴对称覆盖角度为 75° AP-5122m — 12" 双向多功能扬声器,轴对称覆盖角度为 90° 符号说明 “警告!”一词指示有关人身安全的说明。 如果不遵照这些说明,可能会导致人身伤亡。 “小心!”一词指示有关可能造成物理设备损坏的说明。 如果不遵照这些说明操作,可能会导致设备损坏,而且这种 损坏不在质保范围内。 “重要信息!”一词指示对于成功完成某一步骤至关重要的说明或信息。 “注意”一词用于指示其他有用信息。 三角形内带箭头的闪电符号用于提醒用户该产品外壳内存在非绝缘的“危险”电压,会对人体造成电击危 险。 三角形内部的惊叹号用于提醒用户注意本手册中重要的安全、操作和维护说明。 重要安全说明 警告!: 虽然一个人可以提起扬声器,但还是要使用适当的提起技巧,这点很重要。建议阅读以下内容: 有关防止背部损伤和伤害的OSHA技术手册 (http://ww
保修(仅限美国;其它国家,请联系您的经销商或分销商) QSC Audio Products 3 年有限质保 QSC Audio Products, LLC (“QSC”) 担保其产品不会出现材料和/或制造工艺缺陷;若在正常安装和使用条件下出现质量问 题,QSC 将按照本质保协议更换有缺陷的零件并维修故障产品,但前提是,您需要预付运费,将产品送回我们的工厂、 任一授权维修站或授权的 QSC 国际分销商,并附带购买证明(即销售收据)复印件。 此质保协议规定,退回的产品必 须经我们检查断定是否存在制造缺陷。 本质保不适用于任何因误用、疏忽、意外或不正确安装导致损坏的产品或日期 编码被去掉或破损的产品。 QSC 不对意外和/或间接发生的损坏承担责任。 此质保赋予您特定的法律权力。 此有限质保 在质保期内可自由转让。 如果产品购自未经授权的零售商/网上零售商,或者以任何方式去掉、破坏或覆盖了原始出厂 序列号,则此 QSC 产品质保无效。 对于此产品中软件或数据的损坏或丢失,不属于质保范围。 在进行维修或更换服务 时,QSC 将只承担重新安装此产品原始配置软件及后续更新版本等合理范围内的工作,对于所维修设备上非此产品原始
冲击负载 负载移动或停止时,其静态重量会增大。 突然移动可能会使静态重量增大数倍。 这种静态重量的倍增称为“冲击负 载”。 冲击负载会给设备和工作人员带来危险。 冲击负载的影响可能是瞬间的,也可能无法检测到,除非设备出现明 显的损坏。 为了正确应对冲击负载,需要充分了解设备、悬挂和吊装作业并加以细致规划。 设备和结构的冲击负载通常限于吊装和安装过程中,但是自然力量(风、地震等)也可能会造成数倍于静态负载的冲击 负载。 因此,结构和悬挂设备必须能够支撑数倍于所悬挂设备重量的重量。 型号 重量 (kg) 重量 (lbs) AP-5102 21.8 48 AP-5122 29.7 66 AP-5152 36.3 80 AP-5122m 28.
使用轭架安装件 AcousticPerformance 可以使用连接到 M10 集成悬挂点的轭架 安装件来安装扬声器。 需要使用一个 6 mm 六角起子。 M10 ٫ٰ夊 ڐՍֻ֥ ֻ֥ • 型号 AP-5102 (10") 使用 AP-YM10 轭架安装件 • 型号 AP-5122 (12") 使用 AP-YM12 轭架安装件 ҹઅ夊 ੯ֻ • 型号 AP-5122m(12" 多功能)使用 AP-YM12m 轭架安装件 注意: AP-5122m与轭架垂直安装。 请参考图2。 警告!: 在将轭架安装件安装到任何表面上之 前,请咨询结构工程师。确保表面可以支撑 扬声器的重量,并且可以使用适当的螺栓将轭 架固定到此表面上。 —图1— 1.正确将轭架安装支架固定到选定的表面上。 请参考图1和图2。 2.从扬声器机罩顶部和底部卸下中心 M10 六角塞。 可以丢弃或回 收利用这些塞子。 3.利用适当的提起技巧,将扬声器放到轭架中,并且在扬声器机罩 顶部和底部与轭架之间放置两个圆形衬垫。 CHI 4.
连接 AcousticPerformance 扬声器可以在被动模式和双功放模式之间切换。 检查设置端口以确定当前模式。 设置端口中的黄色指示 当前模式。 请参考图3和图4。 注意: 出厂默认模式为无源分频网络模式。 ੴԈࠥڔ Յԅڔࠥݹ —图3— Յԅڔࠥݹ ੴԈࠥڔ CHI 1+ 12+ 2- HPF 1+ 1- HF 2+ 2- N/C NL4 / ஊܺ٫ LPF HF NL4 / ஊܺ٫ LF LF —图4— 从被动模式更改为双功放模式 所有的 AcousticPerformance 扬声器出厂时都配置为被动模式。 要从被动模式更改为双 功放模式或从双功放模式更改为被动模式,请执行以下操作: ԳЈҹЗ夊В 请参考图5和图6。 1.卸下将输入罩固定到位的六个螺丝。 2.卸下输入罩,请小心,不要对连接线束施加过大的压力。 3.从输入罩底部的插孔中拔出线束接头。 —图5— 4.将线束接头插入输入罩底部的其他插孔中。 5.
AcousticPerformance 扬声器线缆连接 警告!: 确保已关闭放大器,并断开放大器的电源连接,或扬声器的电缆未连接到放大器。 请参考图7、图8和图9。 NL4 连接器的针脚编号与阻挡带上的针脚编号对应。 型号 AP-5122m 仅利用 NL4 连接器。 线缆连接 型号 规格 线缆连接 最大线缆规格 AP-5102 10" 双向 NL4 和所包含的 4 针阻挡带 AP-5122 12" 双向 NL4 和所包含的 4 针阻挡带 AP-5152 15" 双向 NL4 和所包含的 4 针阻挡带 AP-5122m 12 英寸双向 10 AWG 双 NL4 请参考图7和图9 1.请参考“从被动模式更改为双功放模式”第5页。 ੴԈࠥڔ Յԅڔࠥݹ 2.
规格 AP-5102 AP-5122 AP-5152 AP-5122m 频率响应 (-10 dB): 60 Hz —18 kHz 48 Hz — 18 kHz 44 Hz — 18 kHz 55 Hz — 18 kHz 功率容量 (续) 被动 双功放 HF 双功放 LF 54 V / 450 W 25 V / 80 W 54 V / 450 W 60 V / 550 W 25 V / 80 W 60 V / 550 W 65 V / 650 W 25 V / 80 W 65 V / 650 W 60 V / 550 W 25 V / 80 W 60 V / 550 W 标称灵敏度 2 94 dB,1 W @1 m 95 dB,1 W @1 m 96 dB,1 W @1 m 95 dB,1 W @1 m 标称覆盖角度 (轴对称) 105˚ 90˚ 75˚ 90˚ 定向因数 (Q) 4.6 6 8.3 6 定向指数 (DI) 6.6 7.8 9.2 7.
通信地址: QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA 电话: 总机:(714) 754-6175 销售和市场部门:(714) 957-7100 或(仅限美国)免费电话 (800) 854-4079 客服部门:(714) 957-7150 或(仅限美国)免费电话 (800) 772-2834 传真: 销售和市场部门传真:(714) 754-6174 客服部门传真:(714) 754-6173 网址: www.qscaudio.com 电子邮件: info@qscaudio.com service@qscaudio.com © 2013 QSC Audio Products, LLC.