TM GX POWER AMPLIFIER SERIES User Manual GX3 300 watts per channel at 8 ohms GX5 500 watts per channel at 8 ohms GX7 725 watts per channel at 8 ohms EN TD-000271-00 REV.
IMPORTANT SAFETY PRECAUTIONS AND EXPLANATION OF SYMBOLS EN 2 1- Read these instructions. 2- Keep these instructions. 3- Heed all warnings. 4- Follow all instructions. 5- WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not use this apparatus near water. 6- Clean only with a dry cloth. 7- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
GX POWER AMPLIFIER SERIES Professional Power Amplifiers WELCOME Thank you for purchasing a QSC Audio amplifier. The GX Series is the latest in a long line of hard-working, low cost amplifiers, designed to produce the best possible results for a wide range of users. In most cases, you can plug and play with no surprises, but for best results, we recommend you review the enclosed user guide. EN UNPACKING Confirm that the amplifier has no visible shipping damage.
FRONT PANEL FEATURES MODEL NUMBER ON-OFF SWITCH Move the rocker switch up to turn on the amplifier. The blue PWR LED will turn on immediately. The red CLIP LEDs may trigger for 1-2 seconds until the amp has completed its turn-on cycle. If no lights come on, check the power cord and the AC reset on the rear panel. COOLING VENTS The internal fan moves air through the chassis to reduce temperature rise. Keep vents clear. The fan speeds up in response to heavy use.
GAIN CONTROLS, CH1, CH2 The markings show attenuation in dB. For normal use, keep the control in the upper half of its range (less than 10 dB of attenuation). If set below half, the source may overload before the amplifier reaches full power. RACK MOUNTING Fits standard 19-inch rack, 2RU. Accepts #10 or 6 mm screws, as determined by the rack rails. Add rear support to prevent damage in portable rigs. EN RED CLIP LEDS Red flashing indicates the amp is being overdriven.
REAR PANEL FEATURES CROSSOVER SWITCH CROSSOVER POSITION EXHAUST VENT Keep vent clear. Install in open-back rack. Splits a full-range signal to drive a subwoofer and top box. CH 1 receives the lows, from 20-100Hz, for the subwoofer. CH 2 receives 100Hz to 20kHz, to power a full range speaker. When using CROSSOVER mode, connect signal to CH 1 only. Use the two Gain controls to balance the LF and HF signals (see Front Panel). EN FULL RANGE POSITION For normal, 2-channel use with all inputs active.
AC BREAKER RESET If the amplifier shuts off after a long burst of power, turn off the AC switch and check the circuit breaker. The button can be pressed back in after a 30 second cool-down period. If the breaker trips repeatedly, the amplifier may need servicing. SERIAL NUMBER AND RATINGS The rated AC voltage and output power is shown on the serial number plate. Record the serial number in a safe place. EN AC INLET SPEAKER CONNECTIONS BINDING POSTS Accepts banana plugs (not permitted in CE regions).
SYSTEM HOOKUP EXAMPLES EN 8
SYSTEM HOOKUP EXAMPLES 9 EN
TROUBLESHOOTING NO POWER, NO LIGHTS, NO FAN Confirm that the AC cord is fully seated and connected to a live outlet. Check the AC source by trying another device such as a lamp. Check the BREAKER on the back of the amplifier by pushing in the button. If the breaker trips off quickly, the amplifier needs servicing. AMPLIFIER LOSES VOLUME EN NO SOUND, WITH BLUE LED ONLY, NO GREEN OR RED LED Confirm that the Gain controls are turned up.
SPECIFICATIONS GX3 GX5 GX7 8Ω, both channels driven 300 W 500 W 725W 8Ω, single channel driven 350 W 600 W 800W 4Ω, both channels driven 425 W 700 W 1000W 4Ω, single channel driven 500 W 850 W 1200W 2Ω, both channels driven, 1% clipping 200 W 350 W 600W SIGNAL TO NOISE (20 Hz – 20 kHz) 100 dB INPUT SENSITIVITY VOLTAGE GAIN AT 8Ω 1.2 Vrms 32.2 dB 34.4 dB 36.
WARRANTY (USA only; other countries, see your dealer or distributor) Disclaimer QSC Audio Products, LLC is not liable for any damage to amplifiers or any other equipment that is caused by negligence or improper installation and/or use of this loudspeaker product.
TM SERIE DE AMPLIFICADORES DE POTENCIA GX Manual del usuario GX3 300 vatios por canal a 8 ohmios GX5 500 vatios por canal a 8 ohmios GX7 725 vatios por canal a 8 ohmios SP TD-000271-00 REV.
IMPORTANTES PRECAUCIONES DE SEGURIDAD Y EXPLICACIÓN DE LOS SÍMBOLOS SP 2 1- Lea estas instrucciones. 2- Conserve estas instrucciones. 3- Observe todas las advertencias. 4- Siga todas las instrucciones. 5- ADVERTENCIA: Para prevenir incendios o descargas eléctricas, no exponga este equipo a la lluvia ni a la humedad. No use este aparato cerca del agua. 6- Límpielo sólo con un paño seco. 7- No obstruya ninguna abertura de ventilación. Instale de acuerdo con las instrucciones del fabricante.
3 SERIE DE AMPLIFICADORES DE POTENCIA GX Amplificadores profesionales de potencia BIENVENIDO Gracias por adquirir un amplificador de QSC Audio. La serie GX es la última de una larga línea de amplificadores resistentes y de bajo costo, diseñados para producir los mejores resultados a una gran variedad de usuarios. En la mayoría de los casos, puede enchufar y reproducir sin sorpresas, pero para obtener resultados óptimos, recomendamos que revise la guía del usuario adjunta.
4 CARACTERÍSTICAS DEL PANEL FRONTAL NÚMERO DE MODELO CONMUTADOR DE ENCENDIDO-APAGADO Mueva el conmutador basculante hacia arriba para encender el amplificador. El indicador LED azul PWR se encenderá inmediatamente. Los indicadores LED rojos CLIP pueden activarse durante 1-2 segundos hasta que el amplificador haya completado su ciclo de encendido. Si no vuelven a encenderse las luces, verifique el cable de alimentación y el restablecimiento de CA en el panel posterior.
5 CONTROLES DE LA GANANCIA, CH1, CH2 Las marcas muestran la atenuación en dB. Para uso normal, mantenga el control en la mitad superior de su intervalo (menos de 10 dB de atenuación). Si se ajusta por debajo de la mitad, la fuente de la señal puede sobrecargarse antes de que el amplificador llegue a la máxima potencia. MONTAJE EN BASTIDOR Cabe en un bastidor estándar de 19 pulgadas, 2RU. Acepta tornillos número 10 o de 6 mm, dependiendo de los rieles del bastidor.
6 CARACTERÍSTICAS DEL PANEL POSTERIOR CONMUTADOR DE CRUCE POSICIÓN DE CRUCE ABERTURA DE DESCARGA Divide una señal de intervalo completo para excitar un subwoofer y caja superior. El canal CH 1 recibe los bajos, de 20 a 100Hz, para el subwoofer. El canal CH 2 recibe 100Hz a 20kHz, para alimentar un altavoz de intervalo completo. Al usar el modo CROSSOVER, conecte la señal únicamente a CH 1. Utilice los dos controles de ganancia para equilibrar las señales LF y HF (consulte el panel frontal).
7 RESTABLECIMIENTO DEL DISYUNTOR DE CA Si el amplificador se apaga después de una explosión larga de potencia, apague el conmutador de CA y revise el disyuntor. El botón puede volver a oprimirse después de un período de enfriamiento de 30 segundos. Si el disyuntor se activa repetidamente, es posible que el amplificador necesite servicio técnico. NÚMERO DE SERIE Y CLASIFICACIONES El voltaje nominal de CA y la potencia de salida se muestran en la placa con el número de serie.
EJEMPLOS DE CONEXIÓN DEL SISTEMA SP 8
EJEMPLOS DE CONEXIÓN DEL SISTEMA 9 SP
RESOLUCIÓN DE PROBLEMAS SIN ALIMENTACIÓN, SIN LUCES, SIN VENTILADOR Confirme que el cable de CA esté completamente asentado y conectado a un tomacorriente activo. Revise la fuente de CA probando con otro dispositivo tal como una lámpara. Revise el DISYUNTOR en la parte posterior del amplificador oprimiendo el botón. Si el disyuntor se dispara rápidamente, el amplificador requiere servicio técnico.
11 ESPECIFICACIONES GX3 GX5 GX7 8Ω, ambos canales excitados 300 W 500 W 725 W 8Ω, un solo canal excitado 350 W 600 W 800 W 4Ω, ambos canales excitados 425 W 700 W 1000 W 4Ω, un solo canal excitado 500 W 850 W 1200 W 2Ω, ambos canales excitados, 1% de recorte 200 W 350 W 600 W SEÑAL A RUIDO (20 Hz – 20 kHz) 100 dB SENSIBILIDAD DE ENTRADA GANANCIA DE VOLTAJE A 8Ω 1.2 Vrms 32.2 dB 34.4 dB 36.
GARANTÍA (sólo para EE.UU.; para otros países, consulte con su vendedor o distribuidor) Renuncia QSC Audio Products, LLC no es responsable de ningún daño a los amplificadores ni a ningún otro equipo que sea causado por negligencia o instalación y/o uso incorrectos de este producto de altavoz.
TM AMPLIFICATEURS DE PUISSANCE SÉRIE GX Manuel d’utilisation GX3 300 watts par canal à 8 ohms GX5 500 watts par canal à 8 ohms GX7 725 watts par canal à 8 ohms FR TD-000271-00 Rév.
PRÉCAUTIONS IMPORTANTES ET EXPLICATION DES SYMBOLES FR 26 1- Lire ces instructions. 2- Conserver ces instructions. 3- Respecter tous les avertissements. 4- Suivre toutes les instructions. 5- AVERTISSEMENT : Pour écarter les risques d’incendie et d’électrocution, ne pas exposer ce matériel à la pluie ou l’humidité. Ne pas utiliser cet appareil près de l’eau. 6- Nettoyer uniquement avec un chiffon sec. 7- Ne pas bloquer les bouches d’aération. Installer conformément aux instructions du fabricant.
AMPLIFICATEURS DE PUISSANCE SÉRIE GX Amplificateurs de puissance de professionnels BIENVENUE Merci d’avoir acheté un amplificateur QSC Audio. La série GX est la dernière venue d’une longue gamme d’amplificateurs à bas coût très efficaces conçus pour produire les meilleurs résultats possibles pour un large éventail d’utilisateurs.
CARACTÉRISTIQUES DU PANNEAU AVANT NUMÉRO DE MODÈLE Interrupteur de marche-arrêt Pousser l’interrupteur à bascule vers le haut pour mettre l’amplificateur en marche. Le voyant PWR bleu s’allume immédiatement. Il est possible que les voyants CLIP rouges s’allument pendant 1-2 secondes jusqu’à ce que l’amplificateur ait terminé son cycle de mise sous tension. Si aucun voyant ne s’allume, vérifier le cordon d’alimentation et le disjoncteur (RESET) sur le panneau arrière.
COMMANDES DE GAIN, CH1, CH2 Les indications correspondent à l’atténuation en dB. Pour une utilisation normale, laisser la commande dans la moitié supérieure de sa plage (moins de 10 dB d’atténuation). En dessous de la moitié, la source risque la surcharge avant que l’amplificateur n’ait le temps d’atteindre sa pleine puissance. FIXATION SUR BÂTI S’installe sur un bâti 2 unités standard de 48 cm. Accepte des vis #10 ou 6 mm, comme indiqué par les rack du bâti.
CARACTÉRISTIQUES DU PANNEAU ARRIÈRE COMMUTATEUR CROSSOVER POSITION DU COMMUTATEUR CROSSOVER ÉVENT D’ÉVACUATION Scinde un signal pleine gamme pour piloter un caisson d’extrêmes graves et une enceinte supérieure. CH 1 reçoit les graves (20-100 Hz) pour le caisson d’extrêmes graves. CH 2 reçoit les fréquences comprises entre 100 Hz et 20 kHz, pour alimenter un haut-parleur pleine gamme. Lorsque le mode CROSSOVER (Filtre passif) est utilisé, connecter le signal à CH 1 uniquement.
COUPE-CIRCUIT (BREAKER) Si l’amplificateur s’arrête après une longue salve, coupez l’interrupteur de marche-arrêt et vérifiez le disjoncteur. Vous pouvez rappuyer sur le disjoncteur (BREAKER) après une période de refroidissement de 30 secondes. Si le disjoncteur saute constamment, l’amplificateur pourra nécessiter une maintenance. NUMÉRO DE SÉRIE ET VALEURS NOMINALES Les valeurs nominales de tension secteur et de puissance de sortie apparaissent sur la plaque du numéro de série.
EXEMPLES DE BRANCHEMENT DU SYSTÈME FR 32
EXEMPLES DE BRANCHEMENT DU SYSTÈME 33 FR
DÉPANNAGE PAS D’ALIMENTATION, VOYANTS ÉTEINTS, VENTILATEUR À L’ARRÊT PAS DE SON, AVEC VOYANT BLEU ALLUMÉ UNIQUEMENT (VOYANT VERT OU ROUGE ÉTEINT) PERTE DE VOLUME DE L’AMPLIFICATEUR PAS DE SON, MAIS LE VOYANT VERT EST ALLUMÉ Confirmer que le cordon d’alimentation secteur est inséré à fond dans une prise sous tension. Vérifier l’état de l’alimentation secteur en branchant un autre appareil, comme une lampe. Vérifier le disjoncteur au dos de l’amplificateur en enfonçant le bouton BREAKER.
CARACTÉRISTIQUES TECHNIQUES GX3 GX5 GX7 8 Ω, deux canaux pilotés 300 W 500 W 725 W 8 Ω, un canal piloté 350 W 600 W 800 W 4 Ω, deux canaux pilotés 425 W 700 W 1000 W 4 Ω, un canal piloté 500 W 850 W 1200 W 2 Ω, deux canaux pilotés, écrêtage de 1 % 200 W 350 W 600 W SIGNAL-BRUIT (20 Hz – 20 kHz) 100 dB SENSIBILITÉ D’ENTRÉE GAIN DE TENSION À 8 Ω 1,2 V (valeur efficace) 32,2 dB 34,4 dB 36.
GARANTIE (États-Unis seulement ; dans les autres pays, consulter le revendeur ou le distributeur) Avis de non-responsabilité QSC Audio Products, LLC n’est pas responsable des dommages subis par les amplificateurs ou tout autre équipement causé par un acte de négligence ou une installation impropre et/ou l’utilisation de ce hautparleur.
TM LEISTUNGSVERSTÄRKER DER SERIE GX Benutzerhandbuch GX3 300 W pro Kanal bei 8 Ohm GX5 500 W pro Kanal bei 8 Ohm GX7 725 W pro Kanal bei 8 Ohm GR TD-000271-00 REV.
WICHTIGE SICHERHEITSVORKEHRUNGEN UND SYMBOLERKLÄRUNG GR 38 1. Diese Anleitung sorgfältig durchlesen. 2. Diese Anleitung gut aufbewahren. 3. Alle Warnhinweise beachten. 4. Alle Anweisungen befolgen. 5. ACHTUNG: Zur Vermeidung von Bränden und Stromschlägen darf diese Ausrüstung weder Regen noch Feuchtigkeit ausgesetzt werden. Dieses Gerät nicht in Wassernähe verwenden. 6. Nur mit einem trockenen Tuch reinigen. 7. Keine Lüftungsöffnungen blockieren. Zur Installation die Anleitung des Herstellers beachten.
LEISTUNGSVERSTÄRKER DER SERIE GX Professionelle Leistungsverstärker WILLKOMMEN Wir freuen uns, dass Sie sich für einen Audioverstärker von QSC entschieden haben. Die Serie GX ist die neueste Weiterentwicklung einer Serie leistungsstarker, preisgünstiger Verstärker, die einem breiten Benutzerspektrum optimale Ergebnisse bieten sollen. In den meisten Fällen können Sie die Verstärker ganz einfach per Plug-and-Play anschließen.
FUNKTIONSMERKMALE DER FRONTPLATTE MODELLNUMMER EIN-AUS-SCHALTER Drücken Sie den Wippschalter nach oben, um den Verstärker einzuschalten. Die blaue Stromanzeige-LED (PWR) schaltet sich sofort ein. Die roten CLIP-LEDs können 1-2 Sekunden lang eingeschaltet werden, bis der Verstärker seinen Einschaltzyklus durchlaufen hat. Wenn keine Anzeigen aufleuchten, überprüfen Sie das Netzkabel und die Netzstrom-Rücksetzfunktion auf der Rückplatte.
VERSTÄRKUNGSREGLER, CH1, CH2 Die Markierungen zeigen die Dämpfung in dB an. Für normale Anwendungen sollte dieser Regler im oberen Messbereich bleiben (Dämpfung von weniger als 10 dB). Wenn er auf einen Wert in der unteren Messbereichshälfte eingestellt wird, kann die Signalquelle überlastet werden, bevor der Verstärker seine volle Leistung erreicht. RACK-EINBAU Passt in ein standardmäßiges 19-Zoll-Rack (2 RU). Zur Befestigung mit 6-mm-Schrauben geeignet, je nach den Rack-Schienen.
FUNKTIONSMERKMALE DER HINTEREN PLATTE CROSSOVER-SCHALTER CROSSOVER-POSITION ENTLÜFTUNGSÖFFNUNGEN Spaltet ein Vollbereichssignal zur Ansteuerung eines Subwoofers und einer Top-Box auf. CH 1 empfängt die niedrigen Frequenzen (20100 Hz) für den Subwoofer. CH 2 empfängt Frequenzen im Bereich von 100 Hz bis 20 kHz für die Versorgung eines Vollbereichslautsprechers. Beim Gebrauch des CROSSOVER-Modus das Signal nur an CH 1 anschließen.
NETZSTROM-TRENNSCHALTERRÜCKSETZUNG Wenn sich der Verstärker nach einem langen Stromstoß ausschaltet, schalten Sie den Netzschalter aus und überprüfen Sie den Trennschalter. Die Taste kann nach einer Abkühlzeit von 30 Sekunden wieder gedrückt werden. Wenn der Trennschalter wiederholt ausgelöst wird, muss der Verstärker möglicherweise gewartet werden. SERIENNUMMER UND NENNDATEN Die Netznennspannung und Ausgangsleistung sind dem Seriennummernschild zu entnehmen.
SYSTEMANSCHLUSSBEISPIELE GR 44
SYSTEMANSCHLUSSBEISPIELE 45 GR
FEHLERSUCHE KEIN STROM, KEINE LEUCHTEN, KEIN GEBLÄSE Bestätigen Sie, dass das Netzkabel ganz eingesteckt und mit einer stromführenden Steckdose verbunden ist. Überprüfen Sie die Netzstromquelle durch versuchsweises Anschließen eines anderen Geräts, z. B. einer Lampe. Überprüfen Sie den TRENNSCHALTER auf der Rückseite des Verstärkers durch Drücken der entsprechenden Taste. Wenn der Trennschalter gleich wieder ausgelöst wird, muss der Verstärker gewartet werden.
TECHNISCHE DATEN GX3 GX5 GX7 8 Ω, beide Kanäle angesteuert 300 W 500 W 725 W 8 Ω, ein Kanal angesteuert 350 W 600 W 800 W 4 Ω, beide Kanäle angesteuert 425 W 700 W 1000 W 4 Ω, ein Kanal angesteuert 500 W 850 W 1200 W 2 Ω, beide Kanäle angesteuert, 1 % Clipping 200 W 350 W 600 W SIGNAL/HINTERGRUNDRAUSCHEN (20 Hz – 20 kHz) 100 dB EINGANGSEMPFINDLICHKEIT SPANNUNGSVERSTÄRKUNG BEI 8 Ω 1,2 Vrms 32,2 dB 34,4 dB 36.
GARANTIE (nur für die USA; wenden Sie sich zwecks Garantieinformationen für andere Länder an Ihren Händler oder Distributor) Haftungsausschluss QSC Audio Products, LLC ist nicht für Schäden an Verstärkern oder anderen Geräten haftbar, die durch Fahrlässigkeit oder eine unsachgemäße Installation und/oder Verwendung dieses Lautsprecherprodukts verursacht werden.
TM GX 功率放大器系列 用户手册 GX3 300 W/通道,8 欧姆 GX5 500 W/通道,8 欧姆 GX7 725 W/通道,8 欧姆 SCH TD-000271-00 REV.
重要安全注意事项和符号说明 SCH 1- 阅读这些规定。 2- 保存好这些规定。 3- 注意所有警告。 4- 遵守这些规定。 5- 警告:为避免着火或电击,不要将设备暴露于雨中或潮湿环境中。 不要靠近水的地方使用本设备。 6- 只能用干布擦拭。 7- 不要堵塞通风口。 根据制造商的说明进行安装。 8- 不要安装在会产生热量的热源附近,如散热器、热调节装置、炉子或者其他设备(包括放大器)。 9- 电器耦合器将交流电源断开,安装后应保持随时可用。 10- 勿使接地插头的安全性失效。 接地插头有两个叶片以及一个接地爪。 较宽的叶片或第三个爪手是为了人身安全而设。 如果所提供的插头和您的插座不匹配,请向电工咨询了解如何更换该旧插座。 本设备应通过保护型接地连接到插座 上。 11- 保护电线防止被踩踏或挤压,尤其要注意插头、电源插座及其离开设备处。 12- 仅限使用 QSC Audio Products 有限公司指定的附件或配件。 13- 仅限使用随本设备或由 QSC Audio Products 有限公司出售的硬件、托架、支架及元件。 14- 在雷电发生期间或长时间不用时,请拔下本设备的插头。
GX 功率放大器系列 专业功率放大器 欢迎 非常感谢您购买 QSC Audio 放大器产品。 GX 系列为最 新式的长线放大器,工作稳定,价格低廉,专为多种用户 取得最佳效果而设计。 对于常规使用,插入即可使用, 但为了取得最佳效果,我们建议您查看所附的用户指南。 拆包 确认放大器表面有无在运输途中造成损坏。 确认放大器 和你所在地区的交流电缆和电压额定值匹配(见后面板上 的序列号铭牌)。 最好不要扔掉包装箱以便在需要时退 还放大器,至少在检测前不要扔掉。 支持与服务 QSC Audio 产品拥有遍及世界各地的分销和服务网络。 当地代理机构可以解答你的疑问并处理你的问题。 SCH 功能 功率等级和娱乐行业最常使用的扬声器匹配。 为 4Ω 和 8Ω 扬声器系统的最大真实净空优化。 QSC 网站 我公司网站 www.qscaudio.
前面板功能 型号 打开/关闭开关 向上推摇臂开关打开放大器。 蓝色的 PWR(电源)LED 将立即点亮。 红色的 CLIP(削波)LED 可能会触发1-2 秒, 直至放大器完成自身的开启循环。 如果没有 灯点亮,请检查电源线以及后面板上的交流重设。 GX3 和 GX5 功率额定 值显示在“规格”页上。 通风口 SCH 内部风扇可使空气通过底盘,以抑制升温。 不要堵塞通风孔。 如果高负载使用, 则风扇转速增加。
增益控制,通道1、通道2 标记显示的衰减单位为 dB。 对于正常使 用,将控制器保持在其范围中上半区(衰减 不超过 10 dB)。 如果设置在下半区,在 放大器还没达到最大功率前声源可能已经 过载。 机架安装 安装标准的 19 英寸机架,2RU。 接受 #10 或 6 毫米螺钉, 如齿轨所确定。 添加后支撑以防损坏便携装置。 SCH 红色削波 LED 红色闪动表示放大器正在过载。 过载过大会触发内部增益减少,以降低过载失 真。 信号电平回复正常后,返回正常增益。 如果红色的 LED 仍然亮起,请参 见故障排除部分。 绿色信号 LED 绿色 LED 在软信号 (-35 dB) 开始闪动,如果信号电平上升,则变成稳定的绿 色。 蓝色电源 LED 蓝色 PWR(电源)LED 表示交流开关开启,放大器接入电源。 两秒钟后即可使 用。 交替增益标记 如果分频开关处于活动状态(见后面板), LF(通道 1)控制低频(亚低音扬声器), HF(通道 2)控制高频(中高音箱)。
后面板功能 分频开关 排气孔 不要堵塞通风孔。 安装开放式背部支架。 分频位置 分解全幅信号驱动亚低音扬声器和顶箱。 通道 1 接收低频 (20-100Hz),供亚低音扬声器。 通道 2 接收 100Hz - 20kHz,驱动全幅扬声器。 如果使用分频模式,仅将信号连接到通道 1。 使用双增益控制平衡低频和高频信号(见前面板)。 全幅位置 SCH 对于正常,双通道使用全部的活动输入。 分频被绕过。 后耳安装 后耳用于保护 后部接头线敷料和 支持支架内放大器。 后支架支撑座 套件(双 FG-000031-00 架型)可 从 QSC 技术服务集团获得。 输入连接 平衡 XLR 输入 引脚 2 正极,引脚 3 负极,引脚 1 屏蔽(接 地)。 建议用于长或短运行,固定或经常变 换。 各通道的 XLR 和 TRS 支架为内部连接, 并提供接入透眼连接其他接头。 平衡 1/4 英寸 TRS 输入 顶端正极,环路负极,套管屏蔽(接地)。 建议 用于经常变换的长运行和短运行。 非平衡 1/4 英寸 TS 输入 对短运行接入非平衡 1/4 英寸插头。 顶端正极,套管屏蔽(接地)。 非平衡声音输入 顶
交流断路器重设 如果放大器在功率长爆发后关闭, 关闭交流开关并检查断路器。 可在 30 秒冷却期后再次按下按钮 。 如果断路器重复跳开, 可能需要对放大器进行维修。 序列号和额定值 额定交流电压和输出功率 显示在序列号铭牌上。 将序列号记录在安全的地方。 SCH 交流输入 扬声器连接 接线柱 接入香蕉插头 (CE 区中不允许)。 裸线或端子可以 插入侧孔。 1/4 英寸接头 将插头插入到 Speakon-Combo 机架的中央。 仅使用重型扬声器线。 SPEAKON 线(2 线型): 插入后转动直至听到接头发出咔的一声。 使用指按门栓或锁紧环松开插头。
系统连接实例 SCH
系统连接实例 SCH
故障排除 无电源,无灯光,无风扇 无声音,只有蓝色 LED,没有绿色或红色 LED 确认将交流线完全插入并连接到了 有电的插座。 试着使用其他设备检查交流电源, 比如灯。 按下按钮检查放大器背面的 断路器。 如果断路器马上跳开, 则需要对放大器进行维修。 确认打开了增益控制。 确认两端的输入缆线安装无误。 如果使用1/4 英寸扬声器缆线,不要将其与输入缆线混 淆。确认有音源输入。 如果需要,使用其他 音源,或者将其他放大器连接到现有音源。 无声音,但是绿色 LED 有响应 放大器失音 SCH 如果放大器工作过重,GuardRail™ 将 降低音量以防因过热而哑音。 风扇应 全速运转。 适当降低输入信号, 1-2 分钟后放大器应回到正常增益。 如果 放大器发烫,而且风扇不转,则需要对其进行 维修。 通道 1 仅出现重低音。 检查后面板上分频开关的位置 。 打开各通道的正常、独立使用 全幅。 通道 2 输入似乎无效。 检查后面板上分频开关的位置 。 打开各通道的正常、独立使用 全幅。 放大器声音失真。 如果红色 CLIP(削波)LED 闪动,则放大器工作 超过正常的额定功率。 Guard
规格 GX3 GX5 GX7 8Ω, 双通道驱动 300 W 500 W 725 W 8Ω, 单通道驱动 350 W 600 W 800 W 4Ω, 双通道驱动 425 W 700 W 1000 W 4Ω, 单通道驱动 500 W 850 W 1200 W 2Ω, 双通道驱动, 1% 削波 200 W 350 W 600 W 信号到噪音 (20 Hz – 20 kHz) 100 dB 输入灵敏度 电压增益 (8Ω) 1.2Vrms 32.2 dB 34.4 dB 36.1 dB 输出电路 B 级 2 层 H 级 2 层 H 级 功率要求(1/8 功率,粉红噪音 在 4Ω 120 V AC 时) 6.3 A 6 A 11.5 A 失真(低于额定功率 1 dB,1 kHz) 8Ω, 低于 0.02% 4Ω, 低于 0.
保修 (仅限美国;其他国家,请联系您的经销商或分销商) 免责声明 QSC Audio Products, LLC. 对于因疏忽或不适当的安装和/或使用本扬声器产品而对放大器或任何其它设备 所造成的任何损坏不承担任何责任。 SCH QSC Audio Products 3 年有限质保协议 QSC Audio Products, LLC.