User manual

ManualsBrandsQSC ManualsFlying AccessoriesU-Bracket

K.2 Series

Yoke Mounting Quick Start Guide

EXPLANATION OF SYMBOLS

The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be

bodily injury or death.

The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not

followed, it may result in damage to the equipment that may not be covered under the warranty.

The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of theprocedure.

The term "NOTE" is used to indicate additional useful information.

The intent of the lightning ﬂash with arrowhead symbol in a triangle is to alert the user to the presence of un-

insulated "dangerous" voltage within the product's enclosure that may be of sufﬁcient magnitude to constitute a

risk of electric shock to humans.

The intent of the exclamation point within an equilateral triangle is to alert the user to the presence of important

safety, and operating and maintenance instructions in this manual.

IMPORTANT SAFETY INSTRUCTIONS

WARNING!: These mounting brackets shall only be used with K.2 Series loudspeakers. Use with other

apparatus could result in instability and possible injury.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Only use attachments/accessories speciﬁed by the manufacturer.

6. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any

way, or has been dropped.

7. Adhere to all applicable, local codes.

8. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical

equipmentinstallation.

9. Before placing or installing any loudspeaker product, inspect all hardware, cabinets, transducers, brackets and

associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could

signiﬁcantly reduce the strength of the installation and should be immediately corrected. Use only hardware which is

rated for the loading conditions of the installation and any possible short-term unexpected overloading. Never exceed

the rating of the hardware or equipment.

TD-000524-00-A

*TD-000524-00*

Summary of content (5 pages)

PAGE 1
K.2 Series Yoke Mounting Quick Start Guide EXPLANATION OF SYMBOLS The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death. The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result in damage to the equipment that may not be covered under the warranty.
PAGE 2
Warranty For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com Yoke Mounting the K.2 Series Loudspeakers WARNING!: Read and follow these instructions carefully. If the loudspeakers are not installed properly, they could fall, causing personal injury or death, and damage to the equipment.
PAGE 3
Assemble the Yoke d Si e e to d Si e sid d Si to e sid e to sid e p To to bo p To to m tto p To bo to m tto bo m tto K8.2 – M5x16 mm K10.2 – M5x16 mm K12.2 – M6x20 mm 3 2 3 3 EN 2 2 1 1 1 — Figure 2 — NOTE: Use the connecting plate for both the standard and expanded configurations of model K12.2. The plate provides strength and it's really hard to lose when it's bolted to the wall! Refer to Figure 2 1. Insert the bolts (1) through both yoke brackets from the back. 2.
PAGE 4
Attach the Loudspeaker to the Yoke IMPORTANT!: The illustrations that follow assume that the yoke is already installed on the desired surface. End to End (top to bottom) Loudspeaker Bottom FRONT Loudspeaker Top EN 4 5 6 7 1 2 3 8 9 10 11 12 2 — Figure 3 — Refer to Figure 3 WARNING!: Use two people to perform the following procedures. On the bottom of the loudspeaker: 1. Remove two M4 - 20 screws (1) from the pole cup (3). 2.
PAGE 5
Side to Side Refer to Figure 4 1. Remove two yoke-mount-point covers (1) from the sides of the loudspeaker enclosure. 2. Insert the M8 - 35 mm button-head screw (2) through the flat washer (3), yoke bracket (4), rubber spacer (5), and mounting adapter (6). 4. Thread the M8 - 35 mm button-head screw (2) into the mounting point on the side of the loudspeaker. 5. 4 2 5 6 3 FRONT 3. Position the mounting adapter (6) so that the arrow is pointing towards the front of the loudspeaker.