675 MacArthur Blvd.
IMPORTANT SAFETY PRECAUTIONS Install in accordance with QSC Audio Product's instructions and under the supervision of a licensed Professional Engineer. WARNING! Before placing, installing, rigging, or suspending any speaker product, inspect all hardware, suspension, cabinets, transducers, brackets and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce the strength of the installation, placement or array.
Introduction The WideLine-8 is a high performance line array system designed for portable and installed sound reinforcement. The current WideLine-8 family is composed of the WL3082 line array element, WL212-sw subwoofer, AF3082-S small array frame, AF3082-L large array frame, PB3082 pull-back bar, EB3082 extension bar, and AF8-10 WideLine-8 to WideLine adapter frame. For further information on available suspension, transport, and signal processing options, please visit the QSC website: http://www.qscaudio.
2 1 Introduction (continued) WL212-sw 4 The WL212-sw subwoofer extends the system’s low-frequency capability to 32 Hz with a compact fourth-order bandpass enclosure. Its two ceramic magnet, 4” voice coil, 12” transducers provide 1100 watt continuous power handling capability. EN 3 5 Figure 2: WL212-sw Subwoofer 1- Front suspension links Many users of line array systems have found that suspending the subwoofers with the array provides audible benefit.
Introduction (continued) 3 Use only shackle holes for suspension of array! 4 Figure 4: AF3082-S Array Frame 2 1- Shackle holes (accept 5/8” (16 mm) screw pin anchor shackle) 2- Center support bar 1 5 3- Suspension plates 4- Lanyard retaining screw for ball-lock pin lanyard 5- Suspension plate attachment holes 6- Ball-lock pins with lanyards 6 EN 1 Figure 5: PB3082 Pull Back Bar 1- Shackle hole (accepts 5/8” (16 mm) screw pin anchor shackle) 2 4 2- Suspension plate attachment holes 3- Ball-lock
Introduction (continued) 1 Figure 9: AF8-10 WideLine-8 to WideLine Adapter Frame 3 2 1- WideLine attachment knuckles 2- Knuckle retaining bolt 5 3- Rear link receiver for WideLine loudspeaker 4- WideLine-8 attachment links 4 5- Suspension plate attachment holes EN Suspending the WideLine-8 Array Rules for Suspension •Correct use of all suspension hardware and components is imperative in sound system suspension and deployment.
Suspending the WideLine-8 Array Table 1: WideLine-8 Working Load Limits1 Figure 10: WL3082 attached to AF3082-S Component Weight 7:1 Design Factor 10:1 Design Factor 12:1 Design Factor EB3082 Extension Bar 27 lb (12.3 kg) 1751 lb (714.3 kg) 1100 lb (500.0 kg) 917 lb (416.7 kg) AF3082-S Array Frame 11 lb (5.0 kg) 746 lb (339.0 kg) 522 lb (237.3 kg) 435 lb (197.7 kg) AF3082-L Array Frame 27 lb (12.3 kg) 1274 lb (579.2 kg) 892 lb (405.5 kg) 743 lb (337.9 kg) PB3082 Pull Back Bar 3 lb (1.
Suspending the WideLine-8 Array Figure 15: WL212-sw attached to AF3082-S. Suspending the WL212-sw beneath AF3082-S or AF3082-L All orientation of product is to be viewed from the rear of the enclosure. The QSC logo on the input plate will appear right side up when the enclosure is oriented properly. 1. Lower the array frame onto the subwoofer and align the appropriate holes in the suspension links and frame, fully insert the ball-lock pins, and ensure all pins lock properly.
Suspending the WideLine-8 Array Pull-Back Bar Figure 13:PB3082 under WL3082 attached to AF3082-S. To use the pull-back bar, attach it to the bottom enclosure’s suspension plates using one of the lower sets of splay angle adjustment holes. Align the pull-back bar’s holes with the suspension plate’s and fully insert the ball-lock pins. Ensure locking action of pins. Use a 5/8” (16 mm) screw-pin anchor shackle to attach to the pull-back bar as required using the shackle holes.
Suspending the WideLine-8 Array Attaching WL212-sw behind WL3082 array using EB3082 and two AF3082-S array frames Figure 18: EB3082 with WL212-sw suspended at rear and WL3082 array suspended at front. 1- Attach both AF3082-S array frames to the extension bar suspension plates by centering the array frame member between the extension bar suspension plates and bolting together using the supplied 3/4” bolts.
Ground Stack Configurations Figure 20: 0° tilt WL3082 on WL212-sw The WL212-sw enclosure is fitted with rubber feet on the bottom making the enclosure itself suitable for ground stack applications. Matching recesses in the enclosure’s top surface facilitate secure stacking of one WL212-sw atop another. The design of the suspension links accommodates uptilt and downtilt when attaching WL3082 enclosures to the WL212-sw. Adjustment range is from -10° to +10°.
WL3082 Connections The WL3082 input connectors are a pair of Neutrik NL8's wired in parallel. See Table 2 or the pinout on the WL3082 input plate (on rear of enclosure). The WL3082 loudspeaker is not equipped with a crossover network. All signal processing must be done before connecting audio power to the loudspeaker.
WL3082 Specifications Frequency Response: 68 - 18,000 Hz (+/- 3 dB) Frequency Range: 62 - 20,000 Hz (-10 dB) Maximum SPL (continuous/peak): HF: 127/133 dB Nominal Coverage (-6 dB included): Horizontal: 140 degrees (500 Hz to 3.2 kHz)Vertical: dependant on cumulative splay angles LF: 122/128 dB Transducers: High Frequency: Single 85W, 16 Ohm, 1.
WL212-sw Specifications EN Frequency Response: 40 - 100 Hz (+/- 3 dB) Frequency Range: 32 - 107 Hz (-10 dB) Maximum SPL (continuous/peak): 129 dB/135 dB Transducer: 1100W, dual 12 inch woofer, 4 inch voice coil, ceramic magnet assembly Recommended Crossover Frequency: 30 - 85 Hz Input Sensitivity: 99 dB Weight: Net: 109 lb (49.4 kg) Enclosure: 0.708 inch (18 mm) Baltic birch plywood, paint finish.
EB3082 Specifications Material: Aluminum 6061-T6 Finish: Black powder coat (White optional) Working Load Limit Information: Component Weight 7:1 Design Factor 10:1 Design Factor 12:1 Design Factor EB3082 Extension Bar 27 lb (12.3 kg) 1751 lb (714.3 kg) 1100 lb (500.0 kg) 917 lb (416.7 kg) 47.8” EN (1213mm) 1.4” (34mm) 4” 6.8” (102mm) (172mm) 4” 10.5” 12 x ø 0.
AF3082-L Specifications Material: Aluminum 6061-T6 Finish: Black powder coat (White optional) Working Load Limit Information: Component Weight 7:1 Design Factor 10:1 Design Factor 12:1 Design Factor AF3082-L Array Frame 27 lb (12.3 kg) 1274 lb (579.2 kg) 892 lb (405.5 kg) 743 lb (337.9 kg) 37.0” (940mm) EN 21.7” (551mm) 20.
PB3082 Specifications Material Aluminum 6061-T6 Finish Black powder coat (White optional) Working Load Limit Information: Component Weight 7:1 Design Factor 10:1 Design Factor 12:1 Design Factor PB3082 Pull Back Bar 3 lb (1.4 kg) 434 lb (197.4 kg) 304 lb 138.2 kg) 253 lb (115.2 kg) 21.7” (551mm) 20.0” (508mm) EN 1.0” (25mm) 3 x ø 0.8” (20mm) 6.3” (159mm) 0.8” 1.
This page was left blank intentionally.
This page was left blank intentionally.
How to Contact QSC Audio Products Mailing address: QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA Telephone Numbers: Main Number (714) 754-6175 Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079 Customer Service (714) 957-7150 or toll free (USA only) (800) 772-2834 EN Facsimile Numbers: Sales & Marketing FAX (714) 754-6174 Customer Service FAX (714) 754-6173 World Wide Web: www.qscaudio.com E-mail: info@qscaudio.com service@qscaudio.
1675 MacArthur Blvd., Costa Mesa, CA, 92626 EE.UU. Número principal (714) 754-6175 Ventas y Comercialización (714) 957-7100 o línea sin costo (sólo para EE.UU.) (800) 854-4079 Servicio al cliente(714) 957-7150 o línea sin costo (sólo en EE.UU.
PRECAUCIONES IMPORTANTES DE SEGURIDAD Instale de acuerdo con las instrucciones de QSC Audio Products y bajo la supervisión de un ingeniero profesional con la debida licencia. ¡ADVERTENCIA! Antes de colocar, instalar, montar o suspender cualquier producto de altavoz, inspeccione todo el equipo físico, la suspensión, las cajas, los transductores, los soportes y el equipo asociado para detectar la existencia de daños.
Introducción El sistema WideLine-8 es un sistema de formación en línea de alto rendimiento diseñado para el refuerzo de sonido portátil e instalado. La actual familia WideLine-8 está compuesta del elemento de formación en línea WL3082, el subwoofer?WL212-sw, el bastidor para formaciones pequeñas AF3082-S, el bastidor para formaciones grandes AF3082-L, la barra de retirada PB3082, la barra de extensión EB3082 y el bastidor adaptador AF8-10 de WideLine-8 a WideLine.
2 1 Introducción (continuación) WL212-sw El subwoofer WL212-sw extiende la capacidad de baja frecuencia del sistema a 32 Hz con una caja compacta de paso de banda de cuarto orden. Sus dos transductores de 12” con imán cerámico y bobina de voz de 4” proporcionan una capacidad de manejo de potencia continua de 1100 vatios. ES Muchos usuarios de sistemas de formación en línea han encontrado que la suspensión de subwoofers con la formación proporciona un beneficio audible.
Introducción (continuación) 3 ¡Utilice únicamente los orificios de grillete para la suspensión de la formación! 4 Figura 4: Bastidor para formaciones AF3082-S 2 1- Orificios de grillete (aceptan grilletes de anclaje con pasador de tornillo de 5/8” (16 mm)) 1 5 2- Barra de soporte central 3- Placas de suspensión 4- Tornillo de retención del acollador para los acolladores del pasador de cierre esférico 5- Orificios para conexión de la placa de suspensión 6 6- Pasadores de cierre esférico con acollado
Introducción (continuación) 1 3 2 Figura 9: Adaptador para bastidores modelo AF8-10 de WideLine-8 a WideLine 1- Nudillos de conexión WideLine 5 2- Perno de retención del nudillo 3- Receptor de la articulación posterior para el altavoz WideLine 4 4- Articulaciones de conexión WideLine-8 5- Orificios para conexión de la placa de suspensión Suspensión de la formación WideLine-8 Reglas para la suspensión •El uso correcto de todos los herrajes y componentes de suspensión es imprescindible al suspender y d
Suspensión de la formación WideLine-8 Tabla 1: Límites de cargas de trabajo de la serie WideLine-81 Componente Peso Factor de diseño 7:1 Factor de diseño 10:1 Factor de diseño 12:1 Barra de extensión EB3082 27 lb (12.3 kg) 1751 lb (714.3 kg) 1100 lb (500.0 kg) 917 lb (416.7 kg) Bastidor para formaciones AF3082-S 11 lb (5.0 kg) 746 lb (339.0 kg) 522 lb (237.3 kg) 435 lb (197.7 kg) Bastidor para formaciones AF3082-L 27 lb (12.3 kg) 1274 lb (579.2 kg) 892 lb (405.5 kg) 743 lb (337.
Suspensión de la formación WideLine-8 Figura 15: Subwoofer WL212-sw conectado a un bastidor AF3082-S. Suspensión del altavoz WL212-sw debajo de bastidores AF3082-S o AF3082-L Toda orientación del producto debe verse desde atrás de la caja. El logotipo de QSC en la placa de entrada deberá estar hacia arriba cuando la caja se orienta correctamente. 1.
Suspensión de la formación WideLine-8 Barra de retirada Figura 13: Barra de retirada PB3082 debajo de un altavoz WL3082 conectado a un bastidor AF3082-S. Para usar la barra de retirada, conéctela a las placas de suspensión de la caja inferior usando uno de los conjuntos inferiores de orificios de ajuste del ángulo de abocinado. Alinee los orificios de la barra de retirada con aquellos de la placa de suspensión e inserte completamente los pasadores de cierre esférico.
Suspensión de la formación WideLine-8 Conexión del altavoz WL212-sw detrás de la formación de altavoces WL3082 usando la barra de extensión EB3082 y dos bastidores para formaciones AF3082-S Figura 18: Barra de extensión EB3082 con subwoofer WL212-sw suspendido en la parte posterior y formación de altavoces WL3082 suspendida en la parte frontal.
Configuraciones apiladas en el suelo Figura 20: Inclinación de 0° del modelo WL3082 sobre el modelo WL212-sw La caja del altavoz WL212-sw tiene patas de caucho en la parte inferior, lo cual permite utilizar la caja misma para aplicaciones de apilado en el suelo. Las cavidades coincidentes en la superficie superior de la caja facilitan el apilado de un altavoz WL212-sw sobre el otro.
Conexiones del modelo WL3082 Los conectores de entrada del subwoofer WL3082 son un par de dispositivos Neutrik NL8 cableados en paralelo. Consulte la tabla 2 o la salida de patillas en la placa de entrada del altavoz WL3082 (en la parte posterior de la caja). El altavoz WL3082 no está equipado con una red de cruce. Todo el procesamiento de la señal debe realizarse antes de conectar la potencia de audio al altavoz.
Especificaciones del modelo WL3082 Respuesta de frecuencias: 68 - 18,000 Hz (+/- 3 dB) Intervalo de frecuencias: 62 - 20,000 Hz (+/- 10 dB) SPL máximo (continuo/pico): HF: 127/133 dB Cobertura nominal (-6 dB incluida): Horizontal: 140 grados (500 Hz a 3.2 kHz) Vertical: depende del ángulo de abocinado acumulativo LF: 122/128 dB Transductores: Alta frecuencia: Salida simple de 85W y 16 ohmios, de 1.
Especificaciones del modelo WL212-sw Respuesta de frecuencias: 40 - 100 Hz (+/- 3 dB) Intervalo de frecuencias: 32 - 107 Hz (- 10 dB) SPL máximo (continuo/pico): 129 dB/135 dB Transductor: 1100W, woofer doble de 12 pulgadas, bobina de voz de 4 pulgadas, conjunto de imán cerámico Frecuencia de cruce recomendada: 30 - 85 Hz Sensibilidad de entrada: 99 dB Peso: Neto: 109 lb (49.4 kg) Caja: Madera contrachapada de abedul báltico de 0.708 pulgadas (18 mm), acabado con pintura.
Especificaciones del modelo EB3082 Material: Aluminio 6061-T6 Acabado: Capa de polvo negro (blanco opcional) Información sobre el límite de la carga de trabajo: Componente Peso Factor de diseño 7:1 Factor de diseño 10:1 Factor de diseño 12:1 Barra de extensión EB3082 27 lb (12.3 kg) 1751 lb (714.3 kg) 1100 lb (500.0 kg) 917 lb (416.7 kg) 47.8” (1213mm) 1.4” (34mm) 4” 6.8” ES (102mm) (172mm) 4” 10.5” 12 x ø 0.
Especificaciones del modelo AF3082-L Material: Aluminio 6061-T6 Acabado: Capa de polvo negro (blanco opcional) Información sobre el límite de la carga de trabajo: Componente Peso Factor de diseño 7:1 Factor de diseño 10:1 Factor de diseño 12:1 Bastidor para formaciones AF3082-L 27 lb (12.3 kg) 1274 lb (579.2 kg) 892 lb (405.5 kg) 743 lb (337.9 kg) ES 37.0” (940mm) 21.7” (551mm) 20.
Especificaciones del modelo PB3082 Material: Aluminio 6061-T6 Acabado: Capa de polvo negro (blanco opcional) Información sobre el límite de la carga de trabajo: Componente Peso Factor de diseño 7:1 Factor de diseño 10:1 Factor de diseño 12:1 Barra de retirada PB3082 3 lb (1.4 kg) 434 lb (197.4 kg) 304 lb (138.2 kg) 253 lb (115.2 kg) 21.7” (551mm) 20.0” (508mm) 1.0” (25mm) ES 3 x ø 0.8” (20mm) 6.3” (159mm) 0.8” 1.
Esta página se ha dejado intencionalmente en blanco.
Esta página se ha dejado intencionalmente en blanco.
Cómo ponerse en contacto con QSC Audio Products Dirección postal: QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 EE.UU. Números de teléfono: Número principal (714) 754-6175 Ventas y Comercialización (714) 957-7100 o línea sin costo (sólo EE.UU.) (800) 854-4079 Servicio al cliente (714) 957-7150 o línea sin costo (sólo en EE.UU.) (800) 772-2834 Ventas y Comercialización FAX (714) 754-6174 Servicio al Cliente FAX (714) 754-6173 Números de fax: ES World Wide Web: www.
1675 MacArthur Blvd.
CONSIGNES IMPORTANTES DE SÉCURITÉ Installer conformément aux instructions de QSC Audio Products et d'un technicien professionnel diplômé. AVERTISSEMENT ! Avant de placer, installer, monter ou suspendre un haut-parleur, inspecter l'état de toute la visserie, du matériel de suspension, des armoires, des transducteurs, des supports et du matériel associé.
Introduction Le WideLine-8 est un système linéaire ultra-performant conçu pour une sonorisation sélective portable et installée. La gamme WideLine8 actuelle de produits se compose du haut-parleur linéaire WL3082, du caisson d'extrêmes graves WL212-sw, du petite cadre de ligne AF3082-S, du grand cadre de ligne AF3082-L, de la barre de rétraction PB3082, de la barre d'extension EB3082 et de cadre adaptateur de ligne WideLine-8/WideLine AF8-10.
2 1 Introduction (suite) WL212-sw 4 Le caisson d'extrêmes graves WL212sw étend la capacité basses fréquences du système à 32 Hz avec une enceinte compacte à bande passante du quatrième ordre. Ses deux transducteurs de 30,5 cm à bobine de 10 cm et aimant en céramique procurent une capacité de gestion de puissance continue de 1 100 W.
Introduction (suite) 3 Utiliser uniquement les trous à manille pour la suspension de la ligne de haut-parleurs ! 4 Figure 4 : Cadre de ligne AF3082-S 2 1- Trous à manille (pour manille à ancre de 16 mm à chevilles à vis) 2- Barre de soutien centrale 1 5 3- Plaques de suspension 4- Vis de fixation de cordon de goupilles verrouillées par bille 5- Trous de fixation de plaque de suspension 6- Goupilles verrouillées par bille avec cordons 6 1 Figure 5 : Barre de rétraction PB3082 1- Trou à manille (pour
Introduction (suite) 1 Figure 9 : Cadre adaptateur WideLine-8/WideLine AF8-10 3 2 1- Charnières de fixation WideLine 2- Boulon de fixation de charnière 5 3- Récepteur de patte de suspension arrière pour haut-parleur WideLine 4- Pattes de fixation WideLine-8 4 5- Trous de fixation de plaque de suspension Suspension de ligne WideLine-8 Règles de suspension •L'utilisation correcte de tout le matériel et composants de suspension est cruciale à la suspension et au déploiement appropriés du système.
Suspension de ligne WideLine-8 Tableau 1 : Limites de charge utile de WideLine-81 Figure 10 : WL3082 attaché à AF3082-S Composant Poids Coefficient de sécurité 7:1 Barre d'extension EB3082 27 lb (12,3 kg) 1751 lb (714,3 kg) 1100 lb (500 kg) 917 lb (416,7 kg) Cadre de ligne AF3082-S 11 lb (5 kg) 746 lb (339 kg) 522 lb (237,3 kg) 435 lb (197,7 kg) Cadre de ligne AF3082-L 27 lb (12,3 kg) 1274 lb (579,2 kg) 892 lb (405,5 kg) 743 lb (337,9 kg) Barre de rétraction PB3082 3 lb (1,4 kg) 434 lb (
Suspension de ligne WideLine-8 Figure 15 : WL212-sw attaché à AF3082-S Suspension du WL212-sw sous AF3082-S ou AF3082-L L'ensemble de l'orientation du produit doit être appréhendée par l'arrière de l'enceinte. Le logo QSC qui apparaît sur la plaque d'entrée se trouvera en haut à droite lorsque l'enceinte est correctement orientée. 1.
Suspension de ligne WideLine-8 Barre de rétraction Figure 13 : PB3082 sous WL3082 attaché à AF3082-S Pour utiliser la barre de rétraction, l'attacher aux plaques de suspension en bas de l'enceinte en utilisant l'un des deux jeux inférieurs de trous d'ajustement d'angle d'ébrasement. Aligner les trous de la barre de rétraction sur ceux de la plaque de suspension, puis insérer à fond les goupilles verrouillées par bille. Vérifier l'action bloquante des goupilles.
Suspension de ligne WideLine-8 Fixation d'un WL212-sw derrière la ligne de haut-parleurs WL3082 à l'aide de EB3082 et deux cadres de ligne AF3082-S Figure 18 : EB3082 avec WL212-sw suspendu à l'arrière et ligne WL3082 suspendue à l'avant. 1- Attacher les deux cadres de ligne AF3082-S aux plaques de suspension sur barre d'extension en centrant le membre du cadre de ligne entre les plaques de suspension sur barre d'extension, avant de les boulonner ensemble à l'aide des boulons fournis de 19 mm.
Configurations en pile au sol Figure 20 : Inclinaison de WL3082 de 0° sur WL212-sw L'enceinte WL212-sw a des pieds en caoutchouc qui permettent de la poser par terre en vue de montages d'enceintes en pile. Les renfoncements sur le dessus de l'enceinte facilitent l'empilage des WL212-sw. La conception des pattes de suspension permet une inclinaison vers le haut ou vers le bas lors de la fixation des enceintes WL3082 au WL212-sw. La plage d'ajustement est comprise entre -10° et +10°.
Branchements du WL3082 Les connecteurs d'entrée des WL3082 se résument à une paire de NL8 Neutrik branchés en parallèle. Pour le descriptif des entrées de la plaque d'entrées de WL3082, voir le tableau (au dos de l'enceinte). Le haut-parleur WL3082 n'est pas équipé d'un réseau de filtre passif. L'ensemble du traitement du signal doit être effectué avant le branchement de l'alimentation audio sur le haut-parleur.
Caractéristiques techniques du WL3082 Réponse en fréquence : 68 à 18 000 Hz (±3 dB) Plage de fréquence : 62 à 20 000 Hz (-10 dB) Niveau sonore maximum (continu/pointe) : HF : 127/133 dB Couverture nominale (-6 dB inclus) : Horizontale : 140 degrés (500 Hz à 3,2 kHz) Verticale : dépend de l'angle d'ébrasement cumulé LF : 122/128 dB Transducteurs : Haute fréquence : Sortie 85 W, 16 ohms, 6 mm unique, aimant de néodyme à membrane en polyimide composite de 7,6 cm Basse fréquence : Double transducteu
Caractéristiques techniques du WL212-sw Réponse en fréquence : 40 à 100 Hz (±3 dB) Plage de fréquence : 32 à 107 Hz (-10 dB) Niveau sonore maximum (continu/pointe) : 129 dB/135 dB Transducteur : Haut-parleur de graves 1 100 W, 30,5 cm, bobine de 10 cm, aimant en céramique Fréquence de filtre passif recommandée : 30 à 85 Hz Sensibilité d'entrée : 99 dB Poids : Net : 109 lb (49,4 kg) Enceinte : Contreplaqué de bouleau de 18 mm, peint.
Caractéristiques techniques de l'EB3082 Matériau : Aluminium 6061-T6 Finition : Revêtement en poudre noir (blanc en option) Informations de charge utile : Composant Poids Coefficient de sécurité 7:1 Coefficient de sécurité 10:1 Coefficient de sécurité 12:1 Barre d'extension EB3082 27 lb (12,3 kg) 1751 lb (714,3 kg) 1100 lb (500 kg) 917 lb (416,7 kg) 47,8” (1 213 mm) 1,4” (34 mm) 4” 6,8” (102 mm) (172 mm) 4” 10,5” 12 x ø 0,8” (102 mm) FR (20 mm) (267 mm) Caractéristiques techniques de l
Caractéristiques techniques de l'AF3082-L Matériau : Aluminium 6061-T6 Finition : Revêtement en poudre noir (blanc en option) Informations de charge utile : Composant Poids Coefficient de sécurité 7:1 Coefficient de sécurité 10:1 Coefficient de sécurité 12:1 Cadre de ligne AF3082-L 27 lb (12,3 kg) 1274 lb (579,2 kg) 892 lb (405,5 kg) 743 lb (337,9 kg) 37,0” (940 mm) 21,7” (551 mm) 20,4” FR (518 mm) 4” (102 mm) 16
Caractéristiques techniques de la PB3082 Matériau : Aluminium 6061-T6 Finition : Revêtement en poudre noir (blanc en option) Informations de charge utile : Composant Poids Coefficient de sécurité 7:1 Coefficient de sécurité 10:1 Coefficient de sécurité 12:1 Barre de rétraction PB3082 3 lb (1,4 kg) 434 lb (197,4 kg) 304 lb (138,2 kg) 253 lb (115,2 kg) 21,7” (551 mm) 20,0” (508 mm) 1,0” (25 mm) 3 x ø 0,8” (20 mm) 6,3” FR (159 mm) 0,8” 1,0” (19 mm) (25 mm) Caractéristiques techniques de l'
Page vierge FR 18
Page vierge FR 19
Comment prendre contact avec QSC Audio Products Adresse : QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468, États-Unis Téléphone : Standard (714) 754-6175 Ventes & Marketing (714) 957-7100 ou numéro vert (États-Unis seulement) (800) 854-4079 Service clientèle (714) 957-7150 ou numéro vert (États-Unis seulement) (800) 772-2834 Télécopieur : Ventes & Marketing TÉLÉCOPIEUR (714) 754-6174 Service clientèle TÉLÉCOPIEUR (714) 754-6173 Site Web : www.qscaudio.
1675 MacArthur Blvd.
WICHTIGE SICHERHEITSVORKEHRUNGEN Die Installation unter der Aufsicht eines lizenzierten Fachtechnikers gemäß der Anleitung von QSC Audio Products vornehmen lassen. ACHTUNG! Inspizieren Sie vor dem Aufstellen, Installieren, Rigging oder Aufhängen von Lautsprecherprodukten alle Befestigungsteile, Aufhängungen, Gehäuse, Wandler, Halterungen und damit in Verbindung stehenden Vorrichtungen auf eventuelle Schäden.
Einführung Beim WideLine-8 handelt es sich um ein Hochleistungs-Line Array-System für tragbare und fest installierte Klangverstärkung. Die aktuelle WideLine-8-Produktreihe besteht aus dem Line Array-Element WL3082, dem Subwoofer WL212-sw, dem kleinen Array-Rahmen AF3082-S, dem großen Array-Rahmen AF3082-L, der Pullback-Schiene PB3082, der Verlängerungsschiene EB3082 und dem WideLine-8 auf WideLine-Adapterrahmen AF8-10.
2 1 Einführung (Fortsetzung) WL212-sw Die Tieftonwiedergabe des Systems wird mit dem Subwoofer WL212-sw in einem kompakten Bandpass-Gehäuse vierter Ordnung auf 32 Hz erweitert. Seine zwei 12Zoll-Wandler mit Keramikmagnet und 4-ZollSchwingspule ermöglichen eine kontinuierliche Belastbarkeit von 1100 Watt. Viele Benutzer von Line Array-Systemen sind der Meinung, dass das Aufhängen der Subwoofer zusammen mit dem Array hörbar klangliche Vorteile bringt.
Einführung (Fortsetzung) 3 Arrays dürfen nur unter Verwendung der Schäkellöcher aufgehängt werden! 4 Abbildung 4: Array-Rahmen AF3082-S 2 1- Schäkellöcher (zur Aufnahme von 5/8-Zoll- (16-mm-) Schraubschäkeln) 2- Mittlere Stützschiene 1 5 3- Aufhängungsplatten 4- Leinensicherungsschraube für Kugelsperrbolzenleine 5- Befestigungslöcher, Aufhängungsplatte 6- Kugelsperrbolzen mit Leinen 6 1 Abbildung 5: Pullback-Schiene PB3082 1- Schäkelloch (zur Aufnahme von 5/8-Zoll- (16-mm-) Schraubschäkeln) 2 4
Einführung (Fortsetzung) 1 Abbildung 9: AF8-10 WideLine-8 auf WideLine Adapterrahmen 3 2 1- WideLine-Befestigungsgelenke 2- Gelenksicherungsbolzen 5 3- Rückseitige Verbindungsaufnahme für WideLine-Lautsprecher 4- WideLine-8-Befestigungsverbindungen 4 5- Befestigungslöcher, Aufhängungsplatte Aufhängen des WideLine-8-Arrays Vorschriftsmäßiges Aufhängen •Sowohl beim Aufhängen als auch beim Einsatz von Sound-Systemen ist die vorschriftsmäßige Verwendung aller Flugbefestigungsteile und komponenten unbedi
Aufhängen des WideLine-8-Arrays Table 1: WideLine-8 Systembetriebslastgrenzwerte1 Komponente Gewicht 7:1 Sicherheitsfaktor 10:1 Sicherheitsfaktor 12:1 Sicherheitsfaktor Verlängerungsschiene EB3082 12,3 kg (27 lb) 714,3 kg (1751 lb) 500 kg (1100 lb) 416,7 kg (917 lb) Array-Rahmen AF3082-S 5, 0 kg (11 lb) 339,0 kg (746 lb) 237,3 kg (522 lb) 197,7 kg (435 lb) Array-Rahmen AF3082-L 12,3 kg (27 lb) 579,2 kg (1274 lb) 405,5 kg (892 lb) 337,9 kg (743 lb) Pullback-Schiene PB3082 1,4 kg (3 lb)
Aufhängen des WideLine-8-Arrays Abbildung 15: Am AF3082-S befestigter WL212-sw. Aufhängen des WL212-sw unter dem AF3082-S oder AF3082-L Die Ausrichtung aller Komponenten erfolgt von der Rückseite des Gehäuses aus gesehen. Das im Eingangsfeld befindliche QSC-Logo ist bei ordnungsgemäßer Gehäuseorientierung richtig ausgerichtet. 1. Senken Sie den Array-Rahmen auf den Subwoofer ab und richten Sie die jeweiligen Löcher in den Aufhängungsverbindungen und im Rahmen aus.
Aufhängen des WideLine-8-Arrays Pullback-Schiene Abbildung 13: PB3082 unter WL3082, an AF3082-S befestigt. Befestigen Sie die Pullback-Schiene unten an den Aufhängungsplatten des Gehäuses. Verwenden Sie dazu eine der unteren Reihen der Spreizwinkel-Einstelllöcher. Richten Sie die Löcher der PullbackSchiene mit denen der Aufhängungsplatte aus und führen Sie die Kugelsperrbolzen ganz ein. Achten Sie darauf, dass die Kugelsperrbolzen einrasten.
Aufhängen des WideLine-8-Arrays Befestigen des WL212-sw hinter Array WL3082 mithilfe von EB3082 und zwei Array-Rahmen AF3082-S Abbildung 18: EB3082 mit rückseitig aufgehängtem WL212-sw und vorne aufgehängtem WL3082 Array. 1- Befestigen Sie beide Array-Rahmen AF3082-S an den Aufhängungsplatten der Verlängerungsschiene, indem Sie das Array-Rahmenelement zwischen den Aufhängungsplatten der Verlängerungsschiene zentrieren und mit den beigepackten 3/4-Zoll-Schrauben montieren.
Bodenstapelkonfigurationen Abbildung 20: 0° Neigung WL3082 auf WL212-sw Das Gehäuse WL212-sw ist mit Gummifüßen versehen, wodurch das Gehäuse selbst auf dem Boden gestapelt werden kann. Passende Vertiefungen oben am Gehäuse sorgen für ein sicheres Stapeln eines WL212-sw auf einem anderen. Die Aufhängungsverbindungen sind so ausgelegt, dass beim Befestigen von Gehäusen WL3082 am WL212sw ein Neigen nach oben bzw. unten ermöglicht wird. Der Einstellungsbereich reicht von -10° bis +10°.
WL3082-Anschlüsse Die WL3082-Eingangsanschlüsse sind ein parallel verdrahtetes Neutrik NL8-Paar Siehe Tabelle 2 oder die Stiftbelegung am WL3082-Eingangsfeld (an der Gehäuserückseite). Der Lautsprecher WL3082 ist nicht mit einem Crossover-Netzwerk ausgerüstet. Die gesamte Signalverarbeitung muss abgeschlossen sein, bevor der Audioleistungsanschluss mit dem Lautsprecher verbunden wird. Schließen Sie kein Vollbereichs-Audiokabel an den Hochfrequenzwandler an, da dies zu Beschädigungen führen kann.
WL3082 – Technische Daten Frequenzgang: 68 - 18.000 Hz (+/- 3 dB) Frequenzbereich: 62 - 20.000 Hz (-10 dB) Maximaler SPL (kontinuierlich/Spitze): HF: 127/133 dB Nennabstrahlung (einschließl.
WL212-sw – Technische Daten Frequenzgang: 40 - 100 Hz (+/- 3 dB) Frequenzbereich: 32 - 107 Hz (-10 dB) Maximaler SPL (kontinuierlich/Spitze): 129 dB/135 dB Wandler: 1100-W-, 12-Ohm-, Doppel-12-Zoll-Woofer, 4-Zoll-Schwingspule, Keramikmagnetbaugruppe Empfohlener Crossover-Frequenzbereich: 30 - 85 Hz Eingangsempfindlichkeit: 99 dB Gewicht: Netto: 49,4 kg (109 lb) Gehäuse: 18-mm- (0,708-Zoll-) Sperrholz, baltische Birke, lackiert Anschlüsse: Zwei (2) parallele Neutrik NL4- und zwei parallele N
EB3082 – Technische Daten Material: Aluminium 6061-T6 Oberflächenausführung: schwarze Pulverbeschichtung (weiß optional) Betriebslastgrenzwerte: Komponente Gewicht 7:1 Sicherheitsfaktor 10:1 Sicherheitsfaktor 12:1 Sicherheitsfaktor Verlängerungsschiene EB3082 12,3 kg (27 lb) 714,3 kg (1751 lb) 500 kg (1100 lb) 416,7 kg (917 lb) 47,8 Zoll (1213 mm) 1,4 Zoll (34 mm) 4 Zoll 6,8 Zoll (102 mm) (172 mm) 4 Zoll 10,5 Zoll 12 x ø 0,8 Zoll (102 mm) (20 mm) (267 mm) DE AF3082-S – Technische Daten
AF3082-L – Technische Daten Material: Aluminium 6061-T6 Oberflächenausführung: schwarze Pulverbeschichtung (weiß optional) Betriebslastgrenzwerte: Komponente Gewicht 7:1 Sicherheitsfaktor 10:1 Sicherheitsfaktor 12:1 Sicherheitsfaktor Array-Rahmen AF3082-L 12,3 kg (27 lb) 579,2 kg (1274 lb) 405,5 kg (892 lb) 337,9 kg (743 lb) 37,0 Zoll (940 mm) 21,7 Zoll (551 mm) 20,4 Zoll (518 mm) DE 4 Zoll (102 mm) 16
PB3082 – Technische Daten Material: Aluminium 6061-T6 Oberflächenausführung: schwarze Pulverbeschichtung (weiß optional) Betriebslastgrenzwerte: Komponente Gewicht 7:1 Sicherheitsfaktor 10:1 Sicherheitsfaktor 12:1 Sicherheitsfaktor Pullback-Schiene PB3082 1,4 kg (3 lb) 197,4 kg (434 lb) 138,2 kg (304 lb) 115,2 kg (253 lb) 21,7 Zoll (551 mm) 20,0 Zoll (508 mm) 1,0 Zoll (25 mm) 3 x ø 0,8 Zoll (20 mm) 6,3 Zoll (159 mm) 0,8 Zoll 1,0 Zoll (19 mm) (25 mm) DE AF8-10 – Technische Daten Material:
Diese Seite wurde absichtlich leer gelassen.
Diese Seite wurde absichtlich leer gelassen.
Kontaktinformationen für QSC Audio Products Postanschrift: QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA Telefonnummern: Zentrale: +1 (714) 754-6175 Verkauf und Marketing +1 (714) 957-7100 oder gebührenfrei (nur in den USA) (800) 854-4079 Kundendienst +1 (714) 957-7150 oder gebührenfrei (nur in den USA) +1 (800) 772-2834 Fax-Nummern: Verkauf und Marketing FAX +1 (714) 754-6174 Kundendienst FAX +1 (714) 754-6173 Internet: www.qscaudio.
1675 MacArthur Blvd.
重要安全注意事项 遵照 QSC Audio Products 公司规定在经认证的专业工程师监督下进行安装。 警告! 放置、安装、装配或悬挂扬声器产品前,检查所有硬件、悬架、搁柜、变频器、支架和相关设备有无损坏。任何额定部件的缺失、 腐蚀、变形或未装载都可能大大降低安装、放置或阵列的强度。以上任何情况都会严重降低安装的安全性,一经发现应立即更正。 仅限使用符合额定加载条件安装并可应付可能的短期突发超载的硬件。切勿超过硬件或设备的额定值。 关于物理设备的安装,请咨询经认证的专业工程师。确保理解并遵循所有当地、州和国家关于悬挂设备安全和操作的规定。 保修 (仅限美国;其它国家,请联系您的经销商或分销商) 免责声明 QSC Audio Products, LLC 对于因疏忽或不适当的安装和 / 或使用本扬声器产品而对放大器或任何其它设备所造 成的任何损坏不承担任何责任。 QSC Audio Products 3 年有限质保协议 QSC Audio Products, LLC ( “QSC”) 担保其产品自销售之日起三年内不会发生材料或制造工艺缺陷;若在正常 安装和使用条件下发生的损坏,QSC 将按照本质保协议更
简介 WideLine-8 为高性能线性阵列系统,用于便携和固定安装声音增强。当前的 WideLine-8 系列包括 WL3082 线性 阵列元件、WL212-sw 亚低音扬声器、AF3082-S 小型阵列架、AF3082-L 大型阵列架、PB3082 回拉杆、EB3082 接 长杆,以及 AF8-10 WideLine-8 到 WideLine 适配器机架。要了解关于悬吊、运送和信号处理选项的更多信息, 请访问 QSC 网站:http://www.qscaudio.com WL3082 线性阵列元件使用两个高功率、钕磁铁,2" 音圈,2.5 分频配置的 8" 低频驱动器。虽然两个低音扬声 器都产生低频,但是只有一个可以覆盖中距离,这样在分频区域中可以获得更好的水平方向性控制。借助 3.
2 1 简介 (续) WL212-sw WL212-sw 亚低音扬声器将系统的 低频能力扩展到 32 Hz,带有紧 凑型四阶带通箱。通过两个陶瓷 磁铁、4” 音圈、12” 变频器使 其具有 1100 瓦的连续功率处理 能力。 线性阵列系统的许多用户都已发 现以阵列悬吊亚低音扬声器的声 音效果非常出色。而且,许多地 方因空间狭小无法进行地面安 装。故此,WL212-sw 包括悬吊五 金件,带有精心选择的适宜悬吊 附件,可以将亚低音扬声器悬挂 安装在 WL3082 阵列顶部或后 面。 悬吊 悬吊 WideLine-8 阵列非常简 单、灵活。机罩装有整体式悬吊 板,用安全插销连接在一起。 CH 4 3 5 图 2:WL212-sw 亚低音扬声器 1- 前悬吊连接 6 2- 后悬吊连接 3- 端口 4- 把手 7 5- 带系索安全插销 6- 亚低音扬声器脚凹槽 8 7- 连接滑块旋钮 8- NL8 和 NL4 Speakon 输入面板 9- 橡胶脚 10- 驱动器检修板 9 11- 安装螺丝 (不要取下!) AF3082-S 和 AF3082-L 阵列架支 持大多数悬吊应用,EB3082
简介 (续) 对于阵列悬空只能使用钩 环孔! 3 4 图 4:AF3082-S 阵列架 2 1- 钩环孔 (接入 5/8" (16 mm) 螺纹销锚钩环) 2- 中央支撑杆 1 5 3- 悬吊板 4- 安全插销系索的系索固定螺丝 5- 悬吊板连接孔 6- 带系索安全插销 6 1 图 5:PB3082 回拉杆 1- 钩环孔 (接入 5/8" (16 mm) 螺纹销锚钩环) 2 4 2- 悬吊板连接孔 3- 带系索安全插销 4- 安全插销系索的系索固定螺丝 3 2 图 6:EB3082 接长杆 1 CH 1- 接长杆 2- 悬吊板固定螺栓 3- 钩环孔 (接入 5/8" (16 mm) 螺纹销锚钩环) 4 4- 悬吊板 3 图 7:CP3082 推车 可容纳 4 个 WL3082 机罩,包括一个软垫盖。 图 8:CP212 推车 可容纳 2 个 WL212-sw 机罩,包括一个软垫盖。 5
简介 (续) 1 图 9:AF8-10 WideLine-8 到 WideLine 适配器机架 3 2 1- WideLine 连接关节 2- 关节固定螺栓 5 3- WideLine 扬声器后部连接接收器 4- WideLine-8 连接件 4 5- 悬吊板连接孔 悬吊 WideLine-8 阵列 悬挂要求 CH - 为了确保声音系统悬吊和布置的效果,请正确使用悬吊五金件以及组件。 - 务必预先计算悬空负载后再进行安装以确保不超出悬空组件和五金件各自的负载极限。 - 研究当地的法律、法规充分了解悬空设备所在场所的悬空负载要求。 - 对于阵列悬空只能使用钩环孔。 - 一定要确保用来支持悬空负载的结构部件的完好性。隐藏性结构部件可能具有隐藏性结构不足。 - 请咨询专业的声音系统安装认证机械或结构工程师对连到建筑物或结构上的所有附件进行检查、确认、批准。 - 切勿想当然-业主或第三方提供的悬空附着点可能达不到悬空负载要求。 - 请让专业的索具装配人士将设备吊装、定位、连接到支撑结构。 - 吊装前一定要对所有的组件进行检查 (机罩、悬空支架、销钉、支架、螺栓、螺
悬吊 WideLine-8 阵列 表 1:WideLine-8 工作负载极限 1 图 10:WL3082 接到 AF3082-S 组件 重量 7:1 设计要素 10:1 设计要素 12:1 设计要素 EB3082 接长杆 27 lb (12.3 kg) 1751 lb (714.3 kg) 1100 lb (500.0 kg) 917 lb (416.7 kg) AF3082-S 阵列架 11 lb (5.0 kg) 746 lb (339.0 kg) 522 lb (237.3 kg) 435 lb (197.7 kg) AF3082-L 阵列架 27 lb (12.3 kg) 1274 lb (579.2 kg) 892 lb (405.5 kg) 743 lb (337.9 kg) PB3082 回拉杆 3 lb (1.4 kg) 434 lb (197.4 kg) 304 lb (138.2 kg) 253 lb (115.2 kg) WL3082 扬声器 38 lb (17.3 kg) 651 lb (296.
悬吊 WideLine-8 阵列 图 15:WL212-sw 连接到 AF3082-S。 将 WL212-sw 悬吊在 AF3082-S 或 AF3082-L 下方 产品的所有朝向均是从机罩后部看到的情况。如果机罩朝向无误的话,输 入板上的 QSC 标志应正面朝上。 1. 将阵列架向下放到亚低音扬声器上,对齐悬吊连接和机架上的对应孔,完 全插入安全销,确定所有销子正确锁定。在阵列架上,用中央孔连接亚低 音扬声器的后部连接 (标记为 0°)。 2. 使用 5/8” (16 mm) 的螺纹销锚钩环以及相应的吊索、缆绳等将 AF3082S 或 AF3082-L 阵列架连到悬挂结构上。 注意!从阵列架悬吊亚低音扬声器时,不能使用 +5° 和 -5° 位 置。 图 16:WL212-sw 悬吊在 AF3082-L 下面 3.
悬吊 WideLine-8 阵列 回拉杆 图 13:连接到 AF3082-S 的 WL3082 下面的 PB3082。 要使用回拉杆,用下面的一组张开角调整孔将它连到机罩 底部的悬吊板上。对齐回拉杆的孔与悬吊板的孔,插好安 全销。确定销子锁好。用 5/8” (16 mm) 螺纹销锚钩环按 照使用钩环的要求将它连接到回拉杆。 注意:所有五金件 / 组件都必须达到负责悬挂的专业工 程师所确定的额定负载。 注意:也可使用 PB3082 来悬吊小型阵列 WL3082 机 罩。详细说明请见第 10 页。 接长杆 如果需要,可以移动接长杆悬吊板,方法是:取下两个 3/ 4" 安装螺栓,移动到选定安装位置后重新连接。紧固扭距 为 100 lb-ft (135.
悬吊 WideLine-8 阵列 使用 EB3082 和两个 AF3082-S 阵列架将 WL212-sw 连接 到 WL3082 阵列后面 图 18:带有悬挂在后部的 WL212-sw 以及悬 挂在前面的 WL3082 阵列的 EB3082。 1- 将阵列架部件定位在接长杆悬吊板中间,然后使用所提供的 3/ 4” 螺栓将其连接起来,从而将两个 AF3082-S 阵列架都连到接长 杆悬吊板上。如果需要,可以移动接长杆悬吊板,方法是:取下两 个 3/4" 安装螺栓,移动到选定安装位置后重新连接。扭距紧固到 100 lb-ft (135.
地面堆放配置 图 20:0° 倾斜 WL3082 在 WL212-sw WL212-sw 机罩底部装有橡胶 脚,这使机罩可以直接进行地 面堆放应用。机罩上表面的匹 配凹槽可保证安全堆放 WL212-sw。 悬吊连接的设计容许在连接 WL3082 机罩到 WL212-sw 时 可以上 / 下倾斜。调整范围为 -10° 到 +10° 。 图 21:-10° 倾斜 WL3082 在 WL212-sw 上 注意:连接滑块和销子位置决定机罩之间 的张开角。 注意:地面堆放多个 WL212-sw 机罩时,悬 吊安全比连接阵列重要。 CH 图 22:+10° 倾斜 WL3082 在 WL212-sw 上 11
WL3082 连接 WL3082 输入接头为一对平行布线的 Neutrik NL8。参见表 2 或 WL3082 输入板上的插脚引线 (在机罩后面)。 WL3082 扬声器没有配备分频网络。所有的 信号都必须在将音频功率接入扬声器之前 处理完成。勿将全幅声音接到高频变频器, 否则可能会造成损坏! 表 2:WL3082 接头引脚 引 脚 连接 1+ 通过 1- 通过 2+ 右低频变频器 + (16 欧姆) 2- 右低频变频器 - (16 欧姆) 3+ 左低频变频器 + (16 欧姆) 3- 左低频变频器 - (16 欧姆) 4+ 高频变频器 + (16 欧姆) 4- 高频变频器 - (16 欧姆) WL212-sw 连接 输入连接 WL212-sw 配有两个 NL8 接头,引脚 1+ 和 1连接到变频器。所有其他 NL8 连接在这两个 NL8 之间平行布线。另外,引脚 1+ 和 1- 平行 连接到 NL4。 CH WL212-sw 也配有两个 NL4 接头,引脚 1+ 和 1- 连接到变频器。NL4 的引脚 2+ 和 2- 平行 连接。只有 NL4 的引脚 1+ 和
WL3082 规格 频率响应: 68 - 18,000 Hz (+/- 3 dB) 频率范围: 62 - 20,000 Hz (-10 dB) 最大 SPL (连续 / 峰值): HF: 127/133 dB 标称覆盖范围 (包括 -6dB): 水平:140 度 (500Hz - 3.2kHz)垂直:取决于累计张开角 LF: 122/128 dB 变频器: 高频: 单 85W,16 欧姆,1.4 英寸出口,3 英寸聚酰亚胺基复合材料隔膜,钕磁铁组 低频: 双 250W,16 欧姆 8 英寸锥形变频器,2 英寸音圈,钕磁铁组, 耐候锥盆 声音分频频率: 高到中:1250 Hz 输入灵敏度: HF:108 dB 中到低:300 Hz LF: 98 dB 重量: 净重:38 lb (17.3 kg)装运:45.5 lb (20.
WL212-sw 规格 频率响应: 40 - 100 Hz (+/- 3 dB) 频率范围: 32 - 107 Hz (-10 dB) 最大 SPL (连续 / 峰值): 129 dB/135 dB 变频器: 1100W,双 12 英寸低音扬声器,4 英寸音圈,陶瓷磁铁组 建议分频频率: 30 - 85 Hz 输入灵敏度: 99 dB 重量: 净重:109 lb (49.4 kg)装运:125 lb (56.7 kg) 机罩: 0.708 英寸 (18 mm) 波罗的海桦木多层胶合板,漆面 接头: 双 (2) Neutrik NL4 和双 Neutrik NL8 均平行布线 (布线情况见表 3) 工作负载极限信息: 组件 重量 7:1 设计要素 10:1 设计要素 12:1 设计要素 WL212-sw 扬声器 109 lb (49.5 kg) 1274 lb (579.2 kg) 892 lb (405.5 kg) 743 lb (337.9 kg) 21.7” CH (551mm) 20” 29” (507mm) (736mm) 19.
EB3082 规格 材料 : 铝 6061-T6 漆面: 黑漆面 (白色可选) 工作负载极限信息: 组件 重量 7:1 设计要素 10:1 设计要素 12:1 设计要素 EB3082 接长杆 27 lb (12.3 kg) 1751 lb (714.3 kg) 1100 lb (500.0 kg) 917 lb (416.7 kg) 47.8” 1.4” 4” 6.8” (102mm) (172mm) 4” 10.5” 12 x ? 0.8” (102mm) AF3082-S 规格 CH 材料 铝 6061-T6 漆面: 黑漆面 (白色可选) 工作负载极限信息: 组件 重量 7:1 设计要素 10:1 设计要素 12:1 设计要素 AF3082-S 阵列架 11 lb (5.0 kg) 746 lb (339.0 kg) 522 lb (237.3 kg) 435 lb (197.7 kg) 21.7” (551mm) 20.2” (514mm) 19.9” (505mm) 2 x 1.0” (25mm) 18.1” 8.
AF3082-L 规格 材料 铝 6061-T6 漆面: 黑漆面 (白色可选) 工作负载极限信息: 组件 重量 7:1 设计要素 10:1 设计要素 12:1 设计要素 AF3082-L 阵列架 27 lb (12.3 kg) 1274 lb (579.2 kg) 892 lb (405.5 kg) 743 lb (337.9 kg) 37.0” 21.7” (551mm) 20.
PB3082 规格 材料 铝 6061-T6 漆面: 黑漆面 (白色可选) 工作负载极限信息: 组件 重量 7:1 设计要素 10:1 设计要素 12:1 设计要素 PB3082 回拉杆 3 lb (1.4 kg) 434 lb (197.4 kg) 304 lb (138.2 kg) 253 lb (115.2 kg) 21.7” (551mm) 20.0” (508mm) 1.0” (25mm) 3 x ? 0.8” (20mm) 6.3” (159mm) 0.8” 1.0” (19mm) (25mm) CH AF8-10 规格 材料 铝 6061-T6 漆面: 黑漆面 (白色可选) 工作负载极限信息: 组件 重量 7:1 设计要素 10:1 设计要素 12:1 设计要素 AF8-10 适配器机架 9 lb (4.1 kg) 326 lb (148.1 kg) 228 lb (103.6 kg) 190 lb (86.4 kg) 19.2” (487mm) 19.0” (482mm) 27.3” (693mm) 0.4” 7.
本页为故意留空。 CH 18
本页为故意留空。 CH 19
联系 QSC Audio Products 通信地址: QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA 电话: 主要号码 (714) 754-6175 销售和市场部门 (714) 957-7100,或免费电话 (仅限美国国内)(800) 854-4079 客服 (714) 957-7150,或免费电话 (仅限美国)(800) 772-2834 销售与市场部门传真 (714) 754-6174 客服传真 (714) 754-6173 传真: 网址: www.qscaudio.com 电子邮件: info@qscaudio.com service@qscaudio.