Operating instructions

ManualsBrandsQuadra-Fire ManualsKitchen Appliances2100 Millennium

2100 MILLENNIUM WOOD STOVE

Advanced Combustion Technology (ACT)

1445 North Highway

Colville, WA 99114

SAVE THESE INSTRUCTIONS

Part 250-6931C November 3 2004

www.quadraﬁre.com

PRIOR TO FIRST FIRE

: Remove all labels from glass. Clean all plated surfaces with a glass cleanser and soft cloth to

prevent staining from ﬁngerprint oils. See page 20 for details.

O-T L

Tested and

Listed by

Beaverton

Oregon USA

OMNI-Test Laboratories, Inc

This manual contains instructions for Installation, Operation & Maintenance. Please read this entire manual

before you install and use your new room heater. Failure to follow instructions may result in property

damage, bodily injury, or even death.

IMPORTANT SAFETY NOTES:

When installing your stove, particular attention should be paid to ﬁre protection. If this room heater is not properly installed,

a house ﬁre may result. To reduce the risk of ﬁre, follow the installation instructions. Contact local building, ﬁre ofﬁcials

or authority having jurisdiction about restrictions, installation inspection and permit requirements in your area.

2) CAUTION: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter ﬂuid, or similar liquids to start or

“freshen up” a ﬁre in this heater. Keep all such liquids well away from the heater while it is in use.

3) During operation, if any part of the stove starts to glow, the stove is in an overﬁred condition. Close the air controls

completely by pulling them out, until the glowing has stopped. OVERFIRING VOIDS YOUR WARRANTY!

4) Cool ashes should be disposed of carefully, using a metal container.

5) Do not burn wet or green wood. Store wood in a dry location.

6) DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA OR ENGINE OIL. Do not

burn treated wood, or wood with salt (driftwood, etc.). Burning materials other than wood (including charcoal) under

adverse conditions may generate carbon monoxide in the home, resulting in illness or possible death.

7) Do not permit creosote or soot to accumulate excessively in the chimney or inside the ﬁrebox.

8) Check your chimney system thoroughly when installing into an existing metal or masonry chimney. Seek professional

advice if in doubt about its condition.

9) Do not connect this unit to a chimnney ﬂue already serving another appliance.

10) Comply with all minimum clearances to combustibles as shown in this manual for this appliance.

11) Build ﬁre on brick ﬁrebox ﬂoor. Do not use grates, andirons or other methods to support fuel.

12) HOT WHILE IN OPERATION! Keep children, pets, clothing and furniture away. Contact can cause skin burns.

13) Do not connect to any air distribution duct or system.

14) RISK OF FIRE! Do not operate with stove door or ash removal system door open.

15) For further information refer to NFPA 211 (US) or CAN/CSA-B365 (Canada).

16) Do not operate without fully assembling all components. Burning your stove wthout the legs attached (if supplied with

unit) will void your warranty, and could present a serious safety hazard.

17) Do not operate with broken glass.

Summary of content (24 pages)

PAGE 1
R 2100 MILLENNIUM WOOD STOVE Advanced Combustion Technology (ACT) Tested and Listed by C O-T L Beaverton Oregon USA OMNI-Test Laboratories, Inc. This manual contains instructions for Installation, Operation & Maintenance. Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death. IMPORTANT SAFETY NOTES: 1) When installing your stove, particular attention should be paid to ﬁre protection.
PAGE 2
100 ACT Millennium Wood Stove R Hearth & Home Technologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance, you have our assurance of commitment to quality, durability, and performance. This commitment begins with our research of the market, including ‘Voice of the Customer’ contacts, ensuring we make products that will satisfy your needs.
PAGE 3
2100 ACT Millennium Wood Stove R TABLE OF CONTENTS MODEL NAME QUADRA-FIRE 2100 MILLENNIUM WOOD STOVE Serial Number Date Purchased Dealership Where Purchased Dealer Phone Listings & Safety Cautions .................................. 4 Installation Materials Needed .............................. 4 Venting System Overview ................................... 4 Dimensions .......................................................... 5 Vent Speciﬁcations ..............................................
PAGE 4
R 2100 ACT Millennium Wood Stove LISTINGS & SAFETY CAUTIONS These installation instructions describe the installation and operation of the QUADRA-FIRE 2100 Millennium woodstove. This stove meets the U.S. Environmental Protection Agency’s 1990 particulate emission standards. The 2100 Millenium is listed by OMNI-Test Laboratories, Inc. to UL Safety Standard 1482, and ULC S627, and (UM) 84-HUD.
PAGE 5
2100 ACT Millennium Wood Stove R DIMENSIONS FRONT VIEW SIDE VIEW 21-3/8" (543mm) 7-7/16" (189mm) CL 25-7/8" (657mm) 10-11/16" (271mm) 23-1/16" (332mm) 5-3/8" (137mm) CL 13-5/8" (346mm) 17.0" (432mm) 12-3/4" (324mm) 9-3/8" (238mm) Back of the stove to glass 22.
PAGE 6
2100 ACT Millennium Wood Stove R CLEARANCES TO COMBUSTIBLES (UL AND ULC) BACKWALL / SIDEWALL A ALCOVE SIDE VIEW B 90° OFF TOP UP & OUT CEILING CLEARANCE C D H G * A G B STOVE TO CEILING CLEARANCE CORNER INSTALLATION ALCOVE TOP VIEW E F C E D F MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS In Inches & (Millimeters) NOTE: All "A" , "C" and "F" Dimensions are to the inside diameter of the flue collar.
PAGE 7
2100 ACT Millennium Wood Stove R FLOOR PROTECTION FLOOR PROTECTION: Floor protector must be noncombustible material, extending beneath heater and to the front/sides/rear as indicated. The ﬂoor must be non-combustible or otherwise adequately protected from radiant heat given off by the unit and from sparks and falling embers. A layer of thin brick or ceramic tile over a combustible ﬂoor is not sufﬁcient.
PAGE 8
R 2100 ACT Millennium Wood Stove CHIMNEY HEIGHT/DRAFT To be sure that your Quadra-Fire stove burns properly, the chimney draft (static pressure) should be approximately -.10” water column (W.C.) during a high burn and -.04” W.C. during a low burn, measured 6” (152mm) above the top of the stove after one hour of operation at each burn setting. NOTE: These are guidelines only, and may vary somewhat for individual installations.
PAGE 9
2100 ACT Millennium Wood Stove FLUE SYSTEMS There are two separate and different parts to a ﬂue system: the chimney connector and the chimney itself. A. B. Single wall connector or stove pipe. This must be at least 24 gauge mild steel or 26 gauge blue steel. The sections must be attached to the stove and to each other with the crimped (male) end pointing toward the stove. See Chimney Connector Diagram below.
PAGE 10
2100 ACT Millennium Wood Stove R SOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLE For the method of installation to a masonry chimney shown in Figures 12A & 12B on page 12, it will be necessary to purchase a 12” (305mm) long 8" (203mm) inside diameter, section of prefabricated listed solid pack chimney to use as a thimble. Purchase a wall spacer, trim collar, and a wall band manufactured to ﬁt the chimney section you purchase.
PAGE 11
2100 ACT Millennium Wood Stove R SOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLE (Cont’d) First, make the frame for the thimble, ensuring it is no smaller than 14" (368mm) square, to maintain a 2" (51mm) air space around the chimney section. Attach the wall spacer to the chimney side of the frame. Then insert the frame into the opening, toe nailing it to the wall studs. Install the wall band in the framing to secure the chimney section in place.
PAGE 12
2100 ACT Millennium Wood Stove R CONNECTION TO A METAL PRE-FABRICATED CHIMNEY When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed precisely. You must also purchase (from the same manufacturer) and install the ceiling support package or wall passthrough and “T” section package, ﬁrestops (where needed), insulation shield, roof ﬂashing, chimney cap, etc. Maintain the proper clearance to the structure as recommended by the manufacturer.
PAGE 13
2100 ACT Millennium Wood Stove R MOBILE HOME INSTALLATION 1. 2. 3. You must use a Quadra-Fire Outside Air Kit Part 831-1780 for installation in a mobile home. An outside air inlet must be provided for combustion and must remain clear of leaves, debris, ice and/or snow. It must be unrestricted while unit is in use to prevent room air starvation Spark Arestor Cap which can cause smoke spillage and an inability to maintain a ﬁre. Smoke spillage can also set off smoke alarms.
PAGE 14
2100 ACT Millennium Wood Stove R OUTSIDE AIR KIT INSTALLATION Part 831-1780 Included in Kit: 1 front cover; ﬁberglass rope; 2 vent straps; venting ﬂange & 4 screws; termination cap & screws. Discard the 2 side covers and 1 rear cover as they are not needed for your Quadra-Fire 2100 Millennium.
PAGE 15
2100 ACT Millennium Wood Stove R OPERATING INSTRUCTIONS IMPORTANT - PLEASE READ BEFORE USING STOVE BURNING PROCESS FINAL STAGE In recent years there has been an increasing concern about air quality. Much of the blame for poor air quality has been placed on the burning of wood for home heating. In order to improve the situation, we at Quadra-Fire have developed cleaner-burning wood stoves that surpass the requirements for emissions established by our governing agencies.
PAGE 16
R 2100 ACT Millennium Wood Stove OPERATING INSTRUCTIONS (Cont’d) IMPORTANT - PLEASE READ BEFORE USING STOVE For maximum operating efﬁciency with the lowest emissions, follow these operating procedures: 1. 2. 3. 4. Regardless of desired heat output, when loading stove, burn your Quadra-Fire with both air controls wide open for 5 to 15 minutes. Regulate burn rate (heat output) by using the Primary Control (immediately under ashcatcher).
PAGE 17
2100 ACT Millennium Wood Stove R OPERATING INSTRUCTIONS (Cont’d) OPACITY This is the measure of how cleanly your stove is burning. Opacity is measured in percent; 100% opacity is when an object is totally obscured by the smoke column from a chimney, and 0% opacity means that no smoke column can be seen. As you become familiar with your stove, you should periodically check the opacity. This will allow you to know how to burn your stove as nearly smoke-free as possible (goal of 0% opacity).
PAGE 18
2100 ACT Millennium Wood Stove R MAINTENANCE and GLASS CARE CREOSOTE FIREBRICK FORMATION AND NEED FOR REMOVAL: When wood is The ﬁrebox of your Quadra-Fire stove is lined with high quality ﬁrebrick, which has exceptional insulating properties. There is no need to use a grate; simply build a ﬁre on the ﬁrebox ﬂoor of your stove. Do not operate stove without ﬁrebrick. burned slowly, it produces tar and other organic vapors which combine with expelled moisture to form creosote.
PAGE 19
2100 ACT Millennium Wood Stove R BRICK REPLACEMENT INSTRUCTIONS Brick Set Part 831-1890 1. After the coals have completedly cooled, remove all old brick 2. Remove new brick set from box and lay out to diagram shown. 3. Lay bottom bricks in unit. 4. Install rear bricks on the top of the bottom bricks. Slide top of bricks under clip on back of ﬁrebox wall and push bottom of brick back. 5. Brick Size 9.0" x 4-1/2" x 1-1/4" 9.0" x 2-1/2" x 1-1/4” 7.0” x 4-1/2" x 1-1/4" 7.
PAGE 20
R 2100 ACT Millennium Wood Stove DOOR HANDLE ASSEMBLY 1. 2. 3. 4. 5. 6. Install washer on door handle shaft. Slide door handle through door. Install second washer(s) as shown. Install key in groove. Align groove in latch cam with key; slide latch cam over shaft Install locknut. CAUTION! DO NOT OVERTIGHTEN LOCKNUT. DOOR HANDLE NEEDS TO MOVE SMOOTHLY. 7. Install spring handle turning in a counter-clockwise motion to desired location on handle.
PAGE 21
00 ACT Millennium Wood Stove R EXPLODED VIEWS 4 1 Nbr 1 2 3 4 5 6 7 8 9 10 11 Part Name Door, Cast Door Handle Glass, Replacement Glass Frame Assembly Glass Frame Screws (10) Hinge Pins Latch, Cam Latch Cam key Locking Nut Spring Handle, 1/2” Trim for Door (Trim Door Assembly only) 12 Washer, Spacing 5 9 8 6 7 10 2 12 3 11 DOOR, GLASS AND DOOR HANDLE ASSEMBLY 1 5 4 Nbr 7 6 2 3 250-6931C November 3, 2004 1 2 3 4 5 6 7 Part Name Bafﬂe, Fiberboard Door Frame Glass Assembly Hinge Pins (2)
PAGE 22
2100 ACT Millennium Wood Stove R ACCESSORIES 831-1701 . . . . . Blower Assembly 832-1082 . . . . . Door Assembly, Black (installed on the stove) 832-1902 . . . . . Door Assembly, Gold Trim DR-21NL. . . . . . Door Assembly, Nickel Trim UK-DRNL . . . . . Nickel Upgrade Kit (includes (2) hinge pins, (3) spring handles) 831-1780 . . . . . Outside Air Kit SERVICE PARTS 831-2040 831-1890 832-0550 473-5040 832-1680 832-0050 831-1900 832-0620 832-0630 . . . . . Bafﬂe, Fiberboard . . . . . Brick Set . . . . .
PAGE 23
2100 ACT Millennium Wood Stove R Lifetime Warranty LIMITED LIFETIME WARRANTY The Hearth & Home Technologies limited Lifetime Warranty guarantees that the following components will work as designed for the lifetime of the stove or Hearth & Home Technologies will repair or replace them.
PAGE 24
R CONTACT INFORMATION: Hearth & Home Technologies 1445 North Highway Colville, WA 99114 Division of HNI INDUSTRIES www.quadraﬁre.com Please contact your Quadra-Fire dealer with any questions or concerns. For the number of your nearest Quadra-Fire dealer, call 1-800-926-4356 CAUTION • Do NOT discard this manual. • Important operating and maintenance instructions included. • Read, understand and follow these instrucitons for safe installation and operation.