Installation manual

ManualsBrandsQuadra-Fire ManualsIndoor Fireplace5100I-GD-B

1 7047-910 October 14, 2013

51-I ACC WOOD INSERT

Automatic Combustion Control (ACC)

Model(s):

5100 ACC

HOT SURFACES!

Glass and other surfaces are hot

during operation AND cool down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

replace.

• Alert children and adults to hazards of high temperatures

• High temperatures may ignite clothing or other

ammablematerials.

• Keepclothing,furniture,draperiesandotherammable

materials away.

WARNING

If the information in these instruc-

tions is not followed exactly, a

remayresultcausingproperty

damage, personal injury, or death.

• Donotstoreorusegasolineorotheram-

mable vapors and liquids in the vicinity of

this or any other appliance.

• Donotoverre-Ifheaterorchimneycon-

nectorglows,youareoverring.Overring

will void your warranty.

• Complywithallminimumclearancesto

combustiblesasspecied.Failureto

complymaycausehousere.

WARNING

Fire Risk.

For use with solid wood fuel only.

Otherfuelsmayoverreandgenerate

poisonous gases (i.e. carbon monoxide).

Installation and service of this appliance should

beperformedbyqualiedpersonnel.Hearth&

HomeTechnologiesrecommendsNFIcertied

professionals, or technicians supervised by an

NFIcertiedprofessional.

WARNING

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

NOTICE: DO NOT DISCARD THIS MANUAL

NOTE

ToobtainaFrenchtranslationofthismanual,pleasecontact

yourdealerorvisitwww.quadrare.com

Pour obtenir une traduction française de ce manuel, s’il vous

plaîtcontactervotrerevendeurouvisitezwww.quadrare.com

Summary of content (24 pages)

PAGE 1
Installation Manual Installation & Appliance Set-Up INSTALLER: Leave this manual with party responsible for use and operation. OWNER: Retain this manual for future reference. NOTICE: DO NOT DISCARD THIS MANUAL WARNING 51-I ACC WOOD INSERT Automatic Combustion Control (ACC) Model(s): 5100 ACC If the information in these instructions is not followed exactly, a fire may result causing property damage, personal injury, or death.
PAGE 2
5100 I-ACC Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided may result in death or serious injury. • CAUTION! Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury. • NOTICE: Indicates practices which may cause damage to the appliance or to property. TABLE OF CONTENTS 1 Important Safety Information A. Insert Certification.
PAGE 3
1 5100 I-ACC Important Safety Information A. Insert Certification WARNING Model: 5100-I (ACC) Insert Laboratory: Intertek Report No: 100323198PRT-001a Type: Solid Fuel Type, Listed Room Heater Standard: UL1482 and ULC S628-93 and (UM) 84-HUD, Mobile Home Approved. Fire Risk. NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the UL1482, (UM) 84-HUD and NPFA211 in the U.S.A.
PAGE 4
5100 I-ACC 2 Install Guide Getting Started A. Design and Installation Considerations B. Draft Draft is the pressure difference needed to vent appliances successfully. When a appliance is drafting successfully, all combustion byproducts are exiting the home through the chimney. CAUTION Check building codes prior to installation. • Installation MUST comply with local, regional, state and national codes and regulations.
PAGE 5
100 I-ACC C. Negative Pressure Negative pressure results from the imbalance of air available for the appliance to operate properly. It can be strongest in lower levels of the house. D.
PAGE 6
5100 I-ACC F. Install Checklist ATTENTION INSTALLER: Follow this Standard Work Checklist This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.
PAGE 7
3 5100 I-ACC Dimensions and Clearances A. Appliance Dimensions NOTE: Flue Collar size is 6 inch (152mm) diameter (ID) A 29-1/16 in. (738mm) 25-1/2 in. (648mm) 37-7/16 in. (951mm) 17-9/16 in. (446mm) 12-3/8 in. (314mm) B 13-1/16 in. (332mm) Figure 7.1 Top View Figure 7.2 Front View A Surround Sizes 26-11/16 in. (678mm) B Standard 43 in. (1092mm) 31 in. (787mm) Large 53 in. (1346mm) 34 in. (864mm) 20-1/8 to 23-1/2 in. (512 to 896mm) 9-1/8 in. (232mm) 15/34 to 19 in.
PAGE 8
5100 I-ACC United States and Canada (UL and ULC) TOP TRIM 32-1/4 819mm 27-1/4 692mm SIDE TRIM SIDE WALL B. Clearances to Combustibles, 40-11/16 1033mm USA 16-3/4 CANADA 24-3/4 (629mm) HEARTH EXTENSION MANTEL USA 23-1/2 CANADA 25-1/2 (648mm) 43-11/16 1110mm FIREPLACE FRONT SURFACE 12in max HEARTH EXTENSION No thermal protection required ember protection only In Canada a full length 6 inch (152mm) S635 flue liner required as per ULC S628. In USA a minimum 5 ft length (1.
PAGE 9
5100 I-ACC C. Locating Your Stove & Chimney Location of the appliance and chimney will affect performance. As shown in Figure 9.1 the chimney should: • Install through the warm space enclosed by the building envelope. This helps to produce more draft, especially during lighting and die down of the fire. • Penetrate the highest part of the roof. This minimizes the affects of wind turbulence and down drafts.
PAGE 10
5100 I-ACC E. 2-10-3 Rule These are safety requirements and are not meant to assure proper flue draft. This appliance is made with a 6 inch (152mm) diameter chimney connector as the flue collar on the unit. • Changing the diameter of the chimney can affect draft and cause poor performance. • It is not recommended to use offsets and elbows at altitudes above 4000 feet above sea level and or when there are other factors that affect flue draft. Less than 10 ft. (305cm) 2 ft. (61cm) 2 ft. (61cm) 10 ft.
PAGE 11
4 5100 I-ACC Chimney Systems A. Venting Systems D. Masonry Chimney Chimney Connector: • Must meet minimum standards of NFPA 211. It is also known as flue pipe or stove pipe. It must be 6 inches (152mm) minimum diameter stainless steel connector pipe. Chimney: The chimney can be new or existing, masonry or prefabricated and must meet the following minimum requirements as specified below. • Must have at least 5/8 inch (16mm) fireclay lining joined with refractory cement.
PAGE 12
5100 I-ACC Masonry Chimney (Cont’d) This insert conforms with the UL 1482 and ULC S628 (Canada) in all respects, and is approved to UL & ULC safety standards for installation and use within a fireplace with a masonry chimney in accordance with NFPA 211 and CAN/ CSA-B365-01.
PAGE 13
5100 I-ACC E. Metal Heat Circulating Masonry This insert conforms with the safety standard UL-1482 and ULC S628 (Canada) in all respects and is approved to UL & ULC safety standards for installation and use within a fireplace with masonry chimney, in accordance with NFPA 211, with a direct flue collar connection. F.
PAGE 14
5100 I-ACC Prefabricated Metal Chimney (Cont’d) H. Altering the Fireplace Inches Millimeters Minimum Width of Cavity Opening - Front 29-1/16 738 Minimum Width of Cavity Opening - Rear 25-1/2 648 Minimum Height 20-3/4 528 Minimum Depth from Front to Rear 17-9/16 446 NOTE: Refer to chimney liner manufacturer for recommendations on supporting the liner. Installtion into fireplaces without a permit will void the listing.
PAGE 15
5100 I-ACC I. Zero-Clearance Fireplace A permit may be required for installations, final approval is contingent of the authority having local jurisdiction. Consult insurance carrier, local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits. Inspect the existing fireplace and chimney for any damage or flaws such as burnouts, metal or refectory warping. J.
PAGE 16
5100 I-ACC 5 Appliance Set-Up A. Outside Air Kit Installation A source of air (oxygen) is necessary in order for combustion to take place. Whatever combustion air is consumed by the fire must be replaced. Air is replaced via air leakage around windows and under doors. In homes that have tightly sealed doors and windows, an outside air source is needed. An optional Outside Air Kit is available. Fire Risk. Asphyxiation Risk.
PAGE 17
5100 I-ACC B. Securing Stove Pipe/Liner to Flue Collar Cast Iron Flue Located on Appliance 1. There are 4 pre-drilled holes in the flue collar 90 degrees apart. Attach the flue collar to the stove pipe/liner. If the seal is questionable use high temperature sealant such as stove mastic Figure 17.1. 2. Attach gasket to bottom side of flue collar with a thin coat of silicone. Drill through all 8 countersunk locations Figure 17.2 Gasket Flue Collar Stove Pipe/Liner Figure 17.1 C.
PAGE 18
5100 I-ACC F. Surround & Trim Kit Installation D. Leveling Legs 1. Lay surround face down on a protected surface to prevent scratching. 1. Remove the 2 screws already installed on each leg. 2. Move legs to the desired height. 2. Using a Phillips head screw driver attach the side surrounds to the top surround using 2 #8 sheet metal screws provided with the kit. Figure 18.3. 3. Re-install the screws to secure in place. 3. Lay the trim face down and place the corner brackets into position. 4.
PAGE 19
5100 I-ACC G. Blower Cord Installation on Left Side The blower cord is shipped to be installed on the right side of the appliance. You may relocate the cord so it is on the left side. You will need to remove the wires, flip them over and remove and reverse the male and female terminals and re-install the wires. The wire harness and components are located on the back side of the right side panel. Relocating Blower Cord to Left Side 1.
PAGE 20
5100 I-ACC Remove Control Plate Disconnect Wires to theSnap Disc Figure 20.1 Remove Strain Relief Figure 20.4 Place Harness Under Tabs Figure 20.2 Figure 20.5 Figure 20.3 Figure 20.
PAGE 21
5100 I-ACC H. Zero Clearance Adjustable Trim Support, 2” to 10” EXPLODED VIEW OF SCISSORS Part No. 841-0990, size 9” x 45” and Part No. ADJSPT-12, size 12” x 50” SCREWS ARE CIRCLED Included in Kit: (1) Trim Top, (1) Trim Front, (2) Trim Sides, Double-Sided Tape (already installed) Tools Needed: Phillips Head Screwdriver, Sheet Metal Shears, Measuring Tape, Gloves DOUBLE-SIDED TAPE DOUBLE-SIDED TAPE Figure 21.1 1. The 10 screws on each set of scissors will already be loose when shipped. Figure 21.
PAGE 22
5100 I-ACC 6 1. Mobile Home Installation An outside air inlet must be provided for combustion and must remain clear of leaves, debris, ice and/or snow. It must be unrestricted while unit is in use to prevent room air starvation which can cause smoke spillage and an inability to maintain a fire. Smoke spillage can also set off smoke alarms. 2. Unit must be secured to the mobile home structure at two attachment points.
PAGE 23
7 5100 I-ACC Accessory List R 51i- ACC-BK Service Parts Beginning Manufacturing Date: July 2011 Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide Stocked at Depot model number and serial number when requesting service parts from your dealer or distributor.
PAGE 24
CONTACT INFORMATION Hearth & Home Technologies 1445 North Highway Colville, WA 99114 Division of HNI INDUSTRIES Please contact your Quadra-Fire dealer with any questions or concerns. For the number of your nearest Quadra-Fire dealer log onto www.quadrafire.com CAUTION DO NOT DISCARD THIS MANUAL • Important operating and • Read, understand and follow these instrucmaintenance instructions for safe installations included. tion and operation.