Owner`s manual

May 23, 2013
7063-173E
Page 37
VOYAGEUR Wood Insert
R
F. Prefabricated Metal Chimney
E. Metal Heat Circulating Masonry
The chimney can be new or existing, masonry or prefabricated
and must meet the following minimum requirements:
• Must be minimum 6 inch (152mm) inside diameter of
high temperature chimney listed to UL 103 HT (2100
o
F)
or ULC S628.
• Must use components required by the manufacturer for
installation.
• Must maintain clearances required by the manufacturer
for installation.
• Refer to manufacturers instructions for installation
•This insert is listed to UL 1482 Standard and is
approved for installation into listed factory-built solid
fuel replaces listed to UL 127 conforming to the follow-
ing specications and instructions:
•The original factory-built clearance replace chimney
cap must be re-installed after installing the approved
chimney liner meeting type UL 103 HT requirements
(2100°F) per UL 1777.
•The liner must be securely attached to the insert ue
collar and the chimney top.
•The air ow of the factory-built solid fuel replace
system must not be altered. The ue liner top support
attachment must not reduce the air ow for the existing
air-cooled chimney system.
•No dilution air is allowed to enter the chimney.
1. Secure the replace damper in the open position.
If this cannot be accomplished, it will be necessary
to remove the damper.
2. Seal damper area of chimney around chimney
connector with a high temperature sealant or seal
insert against the face of the replace.
3. Both methods must be removable and replaceable
for cleaning and re-installation.
This insert conforms with the safety standard UL-1482 and
ULC S628 (Canada) in all respects and is approved to UL &
ULC safety standards for installation and use within a re-
place with masonry chimney, in accordance with NFPA 211,
and CAN/CSA-B365-01.
Minimum Width of Cavity Opening - Front
32-7/8* 835
Minimum Width of Cavity Opening - Rear
19-1/8* 486
Minimum Height
21-1/2* 546
Minimum Depth from Front to Rear
18-1/8* 460
Inches Millimeters
Fire Risk.
When lining air-cooled factory-built chimneys:.
• Run chimney liner approved to UL 1777 Type
HT requirements (2100 degrees F)
• Re-install original factory built chimney cap
ONLY
• DO NOT block cooling air openings in chimney
• Blocking cooling air will overheat the chimney
WARNING
NOTICE: In Canada when using a factory-built chimney it must
be safety listed, Type UL103 HT (2100
o
F) [1149
o
C] CLASS
“A” or conforming to CAN/ULC-S629M, STANDARD FOR
650
o
C FACTORY-BUILT CHIMNEYS.
NOTE: Refer to chimney liner manufacturer for recom-
mendations on supporting the liner. Installation into
replaces without a permit will void the listing.
WARNING! Risk of Fire!
Follow venting manufacturer’s clearances and
instructionswheninstallingventingsystem.
To maintain the functionality of the replace’s chimney
system you may use a Simpson Dura-Vent DuraLiner
Slip Hanger, Part # 4671, and attach to the bottom of the
replace chimney cap to support the liner. You have two
options to completing the installation.
Option one - Not required to use liner cap:
Re-attach the existing top of the chimney cap.
Option two - Using liner cap:
Re-attach the existing top of the chimney cap and install a
new storm collar and a new liner cap.
*Youwillneedtoaddadditionalclearancestothese
dimensionsforyourspecicinstallation.Alsoallowsuf-
cientclearanceifyouareinstallinganoutsideairkit.