Product Name: Float Tux Harness Part #: 02810, 02820, 02830, 02840, A00002 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment!
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St.
Trainer: User: Applicable Safety Standards When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926 Subpart M, OSHA 1910, OSHA 1915, ANSI Z359.1-2007, and ANSI A10.32-2012 standards for fall protection. Personal Flotation Device (PFD) is USCG Type II and Type V approved. Applicable standards and regulations depend on the type of work being done, and also might include state-specific regulations.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Safety Information ! WARNING Failure to understand and comply with safety regulations may result in serious injury or death. Regulations included herein are not all-inclusive, are for reference only, and are not intended to replace a Competent Person’s judgment or knowledge of federal or state standards. Do not alter equipment. Do not misuse equipment.
Prior to EACH use, all equipment in a fall protection system must be inspected for any potential or existing deficiencies that may result in its failure or reduced functionality. IMMEDIATELY remove equipment from service if any deficiencies are found. Equipment must be inspected by a Competent Person at least every six months. These inspections must be documented in equipment instruction manual and on equipment inspection grid label.
Cleaning after use is important for maintaining the safety and longevity of Float Tux Harness. Remove all dirt, corrosives, and contaminants from Float Tux Harness before and after each use. If Float Tux Harness cannot be cleaned with plain water, use mild soap and water, then rinse and wipe dry. NEVER clean Float Tux Harness with corrosive substances. Inspect PFD component according to provided product instructions.
Personal Fall Arrest: Float Tux Harness may be used to support a MAXIMUM 1 Personal Fall Arrest System (PFAS) for use in Fall Arrest applications. Structure must withstand loads applied in the directions permitted by the system of at least 5,000 lbs. Maximum free fall is 6‘, or up to 12’ if used in combination with equipment explicitly certified for such use. Applicable D-ring: Dorsal. Restraint: Float Tux Harness may be used in Restraint applications.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Limitations Fall Clearance: There must be sufficient clearance below the anchorage connector to arrest a fall before the user strikes the ground or an obstruction. When calculating fall clearance, account for a MINIMUM 3’ safety factor, deceleration distance, user height, length of lanyard/SRL, and all other applicable factors.
Two or more snap hooks or carabiners connected to each other. NO. Connector directly to webbing. NO. Two connectors to same D-ring. NO. Incompatible or irregular application, which may increase risk of roll-out. NO. 8 Application that places load on gate. NO. Connector directly to horizontal lifeline. NO. www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Connector to integral lanyard. NO. 6305 S. 231st St., Kent, WA 98032 Connector closed and locked to D-ring. OK.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Correct Anchorage Positioning: This chart details allowable working zones required to reduce risk of swing falls and improper side loading. ALWAYS adhere to information specified by chart.
Description 02810 M Float Tux w/CO2 Cartridge, Class 2 Safety Vest, Integrated Harness, & Pass-Through Buckles 02820 L Float Tux w/CO2 Cartridge, Class 2 Safety Vest, Integrated Harness, & Pass-Through Buckles 02830 XL Float Tux w/CO2 Cartridge, Class 2 Safety Vest, Integrated Harness, & Pass-Through Buckles 02840 XXL Float Tux w/CO2 Cartridge, Class 2 Safety Vest, Integrated Harness, & Pass-Through Buckles A00002 n/a Float Tux Rearming Kit Deployed PFD Component (shown without harness) Gu
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Installation and Use ! WARNING Read and understand all instructions provided with PFD component of Float Tux Harness; these instructions MUST be adhered to. ALL PFAS equipment must be selected and deemed compatible with the Float Tux Harness by a Competent Person. ALWAYS follow all instructions of all equipment used in combination with the Float Tux Harness.
1. Hold at dorsal D-ring, and fully inspect harness according to specifications of this instruction manual. Ensure all straps are not twisted and all buckles are unfastened. 2. Connect leg straps around thighs. Ensure there is no twisting of webbing. Leg straps should never dangle or hang loose. Some steps of adorning a harness may require assistance from another person.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Labels Float Tux Harness Part #: DOM: Date of First Use: __________________. • 1-800-466-6385 • 6305 S. 231st St., Kent, WA 98032 • www.guardianfall.com • Prior to use, read and understand all manufacturer’s instructions provided with equipment at time of shipment. This includes Float Tux Harness manual, as well as all additional instructions pertaining to the inspection, maintenance, and use of the personal flotation device.
This inspection log must be specific to one Float Tux Harness. Separate inspection logs must be used for each Float Tux Harness. All inspection records must be made visible and available to all users at all times. If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE. Guardian Fall Protection Notes www.guardianfall.com Date of First Use: __________________.