Product Name: Temper Anchor Part #: 00455; 00458 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment!
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St.
Trainer: User: Applicable Safety Standards When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.1-2007, and ANSI A10.32-2012 standards for fall protection. Applicable standards and regulations depend on the type of work being done, and also might include state regulations if applicable. Consult regulatory agencies for more information on personal fall arrest systems and associated components.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Safety Information ! WARNING Failure to understand and comply with safety regulations may result in serious injury or death. Regulations included herein are not all-inclusive, are for reference only, and are not intended to replace a Competent Person’s judgment or knowledge of federal or state standards. Do not alter equipment. Do not misuse equipment.
Prior to EACH use, all equipment in a fall protection system must be inspected for any potential or existing deficiencies that may result in its failure or reduced functionality. IMMEDIATELY remove equipment from service if any deficiencies are found. Equipment must be inspected by a Competent Person at least every six months. These inspections must be documented in equipment instruction manual and on equipment inspection grid label.
phone: (800) 466-6385 fax: (800) 670-7892 Repairs to Temper Anchor can only be made by a Guardian Fall Protection representative or an entity authorized by Guardian. Contact Guardian for all maintenance and repair needs at: 1-800-466-6385. If a Temper Anchor fails inspection in any way, immediately remove it from service, and contact Guardian to inquire about its return or repair. Cleaning after use is important for maintaining the safety and longevity of Temper Anchor.
Personal Fall Arrest: Temper Anchor may be used to support a MAXIMUM 1 Personal Fall Arrest System (PFAS) for use in Fall Arrest applications. Structure must withstand loads applied in the directions permitted by the system of at least 5,000 lbs. Maximum free fall is 6‘, or up to 12’ if used in combination with equipment explicitly certified for such use. Applicable D-ring: Dorsal. Restraint: Temper Anchor may be used in Restraint applications.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 6305 S. 231st St., Kent, WA 98032 Guardian Fall Protection Limitations Fall Clearance: There must be sufficient clearance below the anchorage connector to arrest a fall before the user strikes the ground or an obstruction. When calculating fall clearance, account for a MINIMUM 3’ safety factor, deceleration distance, user height, length of lanyard/SRL, and all other applicable factors.
Two or more snap hooks or carabiners connected to each other. NO. Connector directly to webbing. NO. Two connectors to same D-ring. NO. Incompatible or irregular application, which may increase risk of roll-out. NO. 8 Application that places load on gate. NO. Connector directly to horizontal lifeline. NO. www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Connector to integral lanyard. NO. 6305 S. 231st St., Kent, WA 98032 Connector closed and locked to D-ring. OK.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 Correct Anchorage Positioning: This chart details allowable working zones required to reduce risk of swing falls and improper side loading. ALWAYS adhere to information specified by chart.
www.guardianfall.com Components and Specifications # 00455 Adjusts to fit roof pitch. Connection Point (swivel) # 00458 Fastener Installation Hole (x16 per side). 10 Guardian Fall Protection Connection Point (non-swivel) 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 Materials: zinc-plated steel.
www.guardianfall.com phone: (800) 466-6385 fax: (800) 670-7892 MINIMUM substrate thickness requirements: Wood: 3/4” CDX or better. Metal: 20g or better. All fasteners MUST be fully embedded in substrate. Applicable roof pitches: flat to 12/12. Temper Anchor MUST install flush against substrate. NEVER install onto bare rafter or truss. All installation must be done under the supervision of a Competent Person. 1.
3 4 7 5 6 5. A Competent Person must ensure all fasteners are installed correctly. Rubber sheathing on fasteners must be compressed against Temper Anchor. DO NOT over-tighten fasteners. Fasteners are over-tightened if sheathing breaks or is squeezed out from underneath fastener. Unacceptable install. MAXIMUM acceptable install. MINIMUM acceptable install. 6. Attach complete and compatible PFAS to Temper Anchor Connection Point.
www.guardianfall.com Labels Temper Anchor Part #: 1-800-466-6385 Date of manufacture: phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com 6305 S. 231st St. Kent, WA 98032 Prior to use, read and understand all manufacturer’s instructions provided with equipment at time of shipment from manufacturer. Compatible with all applicable OSHA 1910 and 1926 Subpart M, ANSI Z359.1-2007, and ANSI A10.32-2012 regulations. 6305 S. 231st St.
This inspection log must be specific to one Temper Anchor. Separate inspection logs must be used for each Temper Anchor. All inspection records must be made visible and available to all users at all times. If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE. Guardian Fall Protection Notes www.guardianfall.com Date of First Use: __________________. Product lifetime is indefinite as long as it passes pre-use and Competent Person inspections.
