Instructions / Assembly

ManualsBrandsQuality Craft ManualsHeating, Ventilation, and Air Conditioning35 in. Electric Wall-Mount Fireplace in Black

Model: MW914T-35BK

ELECTRIC FIREPLACE

HEATER

IMPORTANT:

PLEASE NOTE: WHEN YOU OPEN THE CARTON, CAREFULLY CHECK THE UNIT

AND MAKE SURE THERE IS NO DAMAGE. IF YOU HAVE ANY PROBLEMS WITH

ASSEMBLING THE UNIT, WITH HOW THE VARIOUS FUNCTIONS WORK OR WITH

DAMAGE OR MISSING PARTS PLEASE CALL 1-800-459-4409 (9:00AM TO

5:00PM EST) IMMEDIATELY FOR SERVICE.

NOTE: DO NOT RETURN UNIT TO THE STORE BEFORE CALLING THE TOLL FREE

NUMBER. DO NOT DISPOSE OF YOUR CARTONS UNTIL YOU ARE COMPLETELY

SATISFIED WITH YOUR NEW ELECTRIC FIREPLACE HEATER.

NOTE: Light bulbs may become loose during shipping. If the ﬂame effect is dim or does

not work, please check that light bulb or bulbs are ﬁnger tight in socket. See instructions

for replacing bulb or bulbs.

INSTRUCTION MANUAL

ATTENTION:

1) Find a location for the electric ﬁreplace heater that is protected from direct sunlight.

2) Do not plug the unit into the power outlet before reading all instructions.

IMPORTANT SAFETY INSTRUCTIONS

WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS

BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY

TO PERSONS, INCLUDING THE FOLLOWING:

1) Read all instructions before using this electric ﬁreplace heater.

2) This electric ﬁreplace heater is hot when in use. To avoid burns, do not let

bare skin touch hot surfaces. Keep combustible materials, such as furniture,

pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) away

from the front of the unit and keep them away from the sides and rear.

3) Extreme caution is necessary when any heater is used by, or near, children

or individuals with disabilities and whenever the ﬁreplace is left operating

and unattended.

4) Always unplug ﬁreplace when not in use.

5) Do not operate any electric ﬁreplace heater with a damaged cord or plug or

after the heater malfunctions, has been dropped or damaged in any manner.

6) Do not use outdoors.

7) This electric ﬁreplace heater is not intended for use in bathrooms, laundry

areas and similar indoor locations. Never locate heater where it may fall into

a bathtub or other water container.

8) Do not run cord under carpeting. Do not cover cord with throw rugs, runners,

or similar coverings. Arrange cord away from trafﬁc area and where it will

not be tripped over.

9) To disconnect ﬁreplace, turn controls to off, then remove plug from outlet.

10) Connect to properly grounded outlets only.

11) Do not insert or allow foreign objects to enter any ventilation or exhaust

opening as this may cause an electric shock or ﬁre, or damage the heater.

12) To prevent a possible ﬁre, do not block air intakes or exhaust in any manner.

Do not use on soft surfaces, like a bed, where openings may become

blocked.

13) A heater has hot and arcing or sparking parts inside. Do not use it in areas

where gasoline, paint, or ﬂammable liquids are used or stored.

14) Use this electric ﬁreplace heater only as described in this manual. Any other

use not recommended by the manufacturer may cause ﬁre, electric shock, or

injury to persons.

15) Avoid the use of an extension cord because the extension cord may overheat

and cause a risk of ﬁre. However, if you have to use an extension cord, the

cord shall be No. 14 AWG minimum size and rated not less than 1875 watts.

16) Caution: Do not plug this product into a receptacle controlled by a wall switch

or dimmer.

17) When storing or transporting the unit and cord, keep in a dry place, free from

excessive vibration and store so as to avoid damage.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE.

CAUTION:

IF YOU USE THIS HEATER IN CONJUNCTION WITH A THERMAL CONTROL, A

PROGRAM CONTROLLER, A TIMER OR ANY OTHER DEVICE THAT SWITCHES THE

HEATER ON AUTOMATICALLY, REMEMBER TO OBSERVE ALL SAFETY WARNINGS

AT ALL TIMES. THE ELECTRIC FIREPLACE HEATER HAS SAFETY OVERHEAT

PROTECTION. IF THE OVERHEAT PROTECTION TRIPS, SWITCH OFF ALL SWITCH

BUTTONS AND WAIT APPROXIMATELY 5 -10 MINUTES. IT SHOULD RESET

AUTOMATICALLY ONCE THE UNIT COOLS DOWN.

WARNING:

PROCEDURES AND TECHNIQUES IF NOT CAREFULLY FOLLOWED WILL RESULT

IN DAMAGE TO THE EQUIPMENT AND WILL EXPOSE THE USER TO THE RISK OF

SERIOUS INJURY, ILLNESS OR DEATH.

THIS ELECTRIC FIREPLACE HEATER IS FOR USE ON 120 VOLTS. THE CORD HAS

A PLUG AS SHOWN AT A IN ILLUSTRATION BELOW. AN ADAPTER AS SHOWN AT

C IS AVAILABLE FOR CONNECTING THREE-BLADE GROUNDING-TYPE PLUGS TO

TWO-SLOT RECEPTACLES. THE GREEN GROUNDING PLUG EXTENDING FROM

THE ADAPTER MUST BE CONNECTED TO A PERMANENT GROUND SUCH AS A

PROPERLY GROUNDED OUTLET BOX. THE ADAPTER SHOULD NOT BE USED IF A

THREE-SLOT GROUNDED RECEPTACLE IS AVAILABLE.

A 15 AMP CIRCUIT IS REQUIRED TO OPERATE THIS HEATER. IF THE BREAKER

TRIPS WHEN THE HEATER IS USED THEN YOU MAY NEED TO MOVE THE HEATER

TO ANOTHER LOCATION OR UNPLUG OTHER APPLIANCES THAT ARE ON THE

SAME CIRCUIT. IF YOU REQUIRE AN EXTENSION CORD USE ONE THAT IS RATED

AT 1875 WATTS.

Summary of content (4 pages)

PAGE 1
Electric FIREPLACE Heater Model: MW914T-35BK IMPORTANT: 15) Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 14 AWG minimum size and rated not less than 1875 watts. 16) Caution: Do not plug this product into a receptacle controlled by a wall switch or dimmer.
PAGE 2
PARTS LIST Step 4: M ount the fireplace to the mounting bracket. The extruded flange on the back of the fireplace shall be fully inserted into the mounting bracket. See Fig. D. Fireplace................................................................................................................ 1 A) Mounting bracket.............................................................................................. 1 B) Mounting screws.........................................................................
PAGE 3
OPERATION BY THE REMOTE CONTROL REPLACING THE LIGHT BULBS Step 1: R emove the front cover by pulling it upward until the front cover has been removed from the 4 locking posts located at 2 sides. See Fig. E. Plug in your electric fireplace heater and it will beep once, this means you have power and your remote is ready to operate your electric fireplace heater. : Standby switch. Press this switch once the unit becomes energized and you can select the following functions as desired.
PAGE 4
WARRANTY CLEANING To clean unit first turn off controls on unit and unplug the unit from power source. To clean glass display panel; remove dust with clean dry cloth or to remove finger prints and other marks clean glass with clean damp cloth. Do not use abrasive cleaners or spray liquids on glass display panel surface. Metal and metal painted parts should be cleaned with damp cloth. Do not use abrasive cleaners or spray liquids on these surfaces.