1Mbps MiniUSB Wireless Adapter Date of Issue: January.
Technical Support The firmware version of the MiniUSB Wireless Adapter is displayed on the utility About window. Users could download the most recent software version from the supplier’s web site or refer to the selling contact for the latest software information. If you have difficulty resolving the problem while installing or using the 11Mbps MiniUSB Wireless Adapter, please contact the supplier for support.
FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
Limited Warranty This Warranty constitutes the sole and exclusive remedy of any buyer or reseller’s equipment and the sole and exclusive liability of the supplier in connection with the products and is in lieu of all other warranties, express, implied or statutory, including, but not limited to, any implied warranty of merchantability of fitness for a particular use and all other obligations or liabilities of the supplier.
Please complete the information below and include it along with your products. Name: Title: Company: Telephone: Fax: Email: City/State/Zipcode: Country: Product Name: Serial Number: MAC Address: Invoice Date: Product Description: If you have any further questions, please contact your local authorized reseller for support.
Table of Contents FCC Information........................................................................................... 2 Limited Warranty.......................................................................................... 3 Chapter 1 About MiniUSB Wireless Adapter...........................................1 1-1 Features and Benefits............................................................................ 1 1-2 Applications.......................................................................
About MiniUSB Wireless Adapter 1 The 11Mbps IEEE 802.11b MiniUSB Wireless Adapter is a standard USB adapter that fits into any standard USB slot in a notebook computer. Its 11Mbps data rate gives equivalent Ethernet speed to access corporate network or the Internet in a wireless environment. In addition, a detachable antenna version is specifically designed for system integrator application. When installed, 11Mbps MiniUSB Wireless Adapter is able to communicate with any 802.11 and 802.
1-2 Applications 11Mbps MiniUSB Wireless Adapter offers a fast, reliable, cost-effective solution for wireless client access to the network in applications like these: 1. Remote access to corporate network information E-mail, file transfer and terminal emulation. 2. Difficult-to-wire environments Historical or old buildings, asbestos installations, and open area where wiring is difficult to deploy. 3.
1-3 Product Kit 11Mbps MiniUSB Wireless Adapter comes with the following items. Please go through each item below. If any of listed items appears to be damaged or missing, please contact your local dealer. 11Mbps MiniUSB Wireless Adapter …… … … … … ….….….. … … x1 l 11Mbps MiniUSB Wireless Adapter… … … … ….… x1 … … … … … … … l MiniUSB Cable … … … … … … … … … … … … … … … … … ….. … .… . ... x 1 l 11Mbps PC Card Software and Documentation CD… … … … … …………… x 1..
2 Getting Started This chapter describes the instructions that guide you through the proper installation of your 11Mbps MiniUSB Wireless Adapter for the Windows XP/2000/ME/98 operating systems. The complete installation of the 11Mbps MiniUSB Wireless Adapter consists of the following steps: STEP 1 : Install the corresponding driver and utility. STEP 2 : Set basic settings. STEP 34: Finish Installation.
Install Driver for Windows 3 This section describes the installation of the 11Mbps MiniUSB Wireless Adapter driver for the Windows 98/ME/2000 and Windows XP operating systems. The installation procedures for Windows XP refer to 3-1 Set up MiniUSB Wireless Adapter for Windows XP; for Windows 2000 please see 3-2 Set up MiniUSB Wireless Adapter for Windows 2000; for Windows 98/ME refer to 3-3 Set up MiniUSB Wireless Adapter for Windows 98/ME.
-6-
Step 2: Insert the Product CD-ROM into the CD-ROM drive. Check the “Search removable media (floppy, CD-ROM… )” check box and click on Next to install the driver. Step 3: The windows will find “MiniUSB Wireless Adapte r” and start copying corresponding files into the system. Click on Next to continue.
Step 4: Click Finish to complete the installation. Step 5: Right click “My Computer” from Start , select Properties , go to the Hardware tab and click the Device Manager button to see if any error icon appears next to the Network Adapter/MiniUSB Wireless Adapter. If no, your 11Mbps MiniUSB Wireless Adapter is working well. Check if there is any error icon next to the IEEE 802.
Step 5: After installing the MiniUSB Wireless Adapter, the Windows XP will display a “Wireless Network Connection # ” message. Click on the message and the “Automatic Wireless Network Configuration will then appear automatically and allow use to choose to connect a wireless infrastructure network (Access Point), shown as the below figure. You may click the Advanced button to make advanced configuration for the Wireless LAN CF Card, shown as below.
For more information on using the automatic wireless network configuration please refer to Windows XP Help file. If you desire to use our WLAN Utility, you need to disable the Windows XP Automatic Wireless Network Configuration first by un-checking this check box. However, the WLAN Utility, which comes with the MiniUSB Wireless Adapter, provides you more tools to configure the MiniUSB Wireless Adapter and monitor the wireless connection.
3-2 Set up MiniUSB Wireless Adapter for Windows 2000 Step 1: After inserting the 11Mbps MiniUSB Wireless Adapter into the USB slot on your computer, Windows will auto-detect the 11Mbps MiniUSB Wireless Adapter. Step 2: A “Found New Hardware Wizard” window shows up. Click Next to proceed.
Step 3: Select “Search for a suitable driver for my device (recommended) ”. Step 4: Insert the Product CD-ROM into the CD-ROM drive. Specify the location where the driver is placed. Click on Next to install the driver.
Step 5: The windows will find “USB Device”. Click on Next to continue. Step 6: Click Finish to complete the installation.
Step 7: Open Control Panel/System/Device Manager, and check Network Adapters to see if any error icon appears. If no, your MiniUSB Wireless Adapter is working well. Check if there is any error icon next to the MiniUSB Wireless Adapter 3-3 Set up MiniUSB Wireless Adapter for Windows 98/ ME Step 1: After inserting the 11Mbps MiniUSB Wireless Adapter into the USB slot on your computer, Windows will auto-detect new hardware and will display an “Add New Hardware Wizard” window. Click Next to continue.
Step 2: Select “Search for the best driver for your device (Recommended) ” and click Next to proceed. Step 3: Insert the Product CD-ROM into the CD-ROM drive. Select the “CD-ROM drive” check box and click on Next to install the driver.
Step 4: The Windows will find “MiniUSB Wireless Adapter”. Click Next to continue. Step 5: Once the [Please insert the disk labeled “Windows 98/ME CD-ROM”, and then click OK] window appears, enter the path corresponding to the appropriate drives and click OK. Usually these files can be found at C:Windows or C:Windows\system. Step 6: Click Finish to complete the software installation.
Step 7: Restart the computer. Step 8: Open Control Panel/System/Device Manager, and check Network Adapters to see if any error icon appears next to the IEEE 802.11 MiniUSB Wireless Adapter. If no, your 11Mbps MiniUSB Wireless Adapter is working well.
Configure the MiniUSB Adapter 4 This chapter gives you assistance with detailed configuration for the 11Mbps MiniUSB Wireless Adapter under Windows XP/2000/98/ME. 4-1 Install the WLAN Utility To install the WLAN Utility, follow these steps: Step 1: Insert the Product CD-ROM or floppy disk again. Step 2: Go to the utility folder and run setup.exe. Step 3: The InstallShield Wizard will show up and guide you through the rest of the setup process.
Select a program folder and click Next. You may add a shortcut in the startup folder as desired. Upon completion, go to Program Files and run the WLAN Utility and its icon will appear in the System Tray in the bottom right corner of your task bar. Clicking on the icon will open the configuration window. System Tray again. When you minimize the window, the system tray icon will be loaded in the The color behind the system tray icon indicates the link status: Blue indicates a good or excellent link.
4-2 Use the WLAN Utility The WLAN Utility enables you to make configuration changes and perform user-level diagnostics on your 11Mbps MiniUSB Wireless Adapter in the Windows XP/2000/98/ME operating system environments. The WLAN Utility consists of window with 5 items for you to monitor and configure the 11Mbps MiniUSB Wireless Adapter: Configuration, Loop Back, AP Browser, Site Survey and About.
Profile The Profile field allows you to set values for all parameters by selecting a previously defined profile. To create the profile, go to the Profile field, type a profile name and set the corresponding parameters. If one of the profiles is no longer used, you may remove it by clicking the Delete button. After changing parameters, save the profile and click the Apply button to take effect. You can have multiple profiles and modify the profile at any time.
ESSID The ESS ID is the unique ID used by Access Points and stations to identify a wireless LAN. Wireless clients associating to any Access Point must have the same ESSID. The default setting is ANY, which allows your MiniUSB Wireless Adapter to automatically associate to any Access Point (Infrastructure mode) in the vicinity of your wireless adapter. Alternatively, you may check the ESS ID check box to specify the ESS ID.
WEP To prevent unauthorized wireless stations from accessing data transmitted over the network, the WLAN Utility offers highly secure data encryption, known as WEP, making your data transmission over air more secure. To activate the WEP Encryption, check the WEP Enabled check box. An Encryption window will then appear. The instructions are as follows: Ø Pull down the Encryption (WEP) menu and select either 64bit or 128bit encryption method. Ø Specify the encryption keys.
Create Encryption Keys Manually You can also create encryption keys manually by clicking the Create Keys Manually check box. For 64bit encryption you may choose: n Alphanumeric : 5 characters (case sensitive) ranging from “a-z”, “A-Z” and “0-9” (e.g. MyKey) n Hexadecimal: 10 hexadecimal digits in the range of “A -F”, “a-f” and “0-9” (e.g. 11AA22BB33) For 128bit encryption you may choose: n Alphanumeric : 13 characters (case sensitive) ranging from “a-z”, “A-Z” and “0-9” (e.g.
Advance The WLAN Utility also offers the advanced configuration for user to set the 11Mbps MiniUSB Wireless Adapter under certain network environment. These advanced options include Power Management, RTS/CTS and Fragmentation Threshold. To enable the advanced configuration, go to the Configuration tab and click the Advance button. Power Management The Power Save option is designed to conserve battery life of you computer.
Thus, the RTS Threshold mechanism provides a solution to prevent data collisions. When you enable RTS Threshold on a suspect “hidden station”, this station and its Access Point will use a Request to Send/Clear to Send protocol (RTS/CTS). The station will send an RTS to the Access Point, informing that it is going to transmit the data. Upon receipt, the Access Point will respond with a CTS message to all station within its range to notify all other stations to defer transmission.
Status: The Status field on the Configuration menu provides the following information. State: When operating in Infrastructure mode, this field shows the MAC address of the Access Point with which the MiniUSB Wireless Adapter is communicating. When operating in Ad-Hoc mode, it shows the virtual MAC address used by computers participating in the Ad-Hoc network. Current Channel: Shows the channel on which the connection is made. Current Tx Rate: Shows the highest transmit rate of the current association.
Loop Back: The Loop Back tool helps you examine data transmission quality between your 11Mbps MiniUSB Wireless Adapter and any workstation on the network. By entering IP address of 2 remote station, setting ping interval and packet size, you may know whether communication has been made successfully or not. Additionally, you may run the loopback test (proprietary) by clicking the Loop back button to verify the communication quality between your wireless station and Access Point.
Site Survey: When the Site Survey screen is displayed, the channel quality of all 14 radio channels will be displayed. These channel quality measurements are shown on each gauge for the 14 radio channels. The blue bar indicated the channel quality is clear and good. The higher the blue bar is, the better quality you have (i.e., less interference). The yellow bar indicates the channel quality is fair and the red bar indicates the channel is busy or having severe interference.
Limited Warranty This Warranty constitutes the sole and exclusive remedy of any buyer or reseller’s equipment and the sole and exclusive liability of the supplier in connection with the products and is in lieu of all other warranties, express, implied or statutory, including, but not limited to, any implied warranty of merchantability of fitness for a particular use and all other obligations or liabilities of the supplier.
Please complete the information below and include it along with your products. Name: Title: Company: Telephone: Fax: Email: City/State/Zipcode: Country: Product Name: Serial Number: MAC Address: Invoice Date: Product Description: If you have any further questions, please contact your local authorized reseller for support.
