Quanta LM175 Test Operation Guide Version 0.1 Jun.
Contents 1. Introduction .................................................................................................................................... 3 2. Test Environment ............................................................................................................................ 3 2.1. Uninstallation ......................................................................................................................... 3 2.1.1. Windows 7 (32 bit) ...................................
Revision History Version 0.1 Release Date Jun.
1. Introduction This document gives the guidance on how to test Quanta devices. 2. Test Environment Quanta LM175 device supports Windows XP, Windows Vista (32 bit), and Windows 7 (32 bit) operating system. It’s recommended to install Quanta LM175 software in Windows 7 32-bit OS. 2.1. Uninstallation In order to install latest version of software, uninstallation of previous version is required, including drivers, connection manager, and corresponding software tools. 2.1.1. Windows 7 (32 bit) 1.
3. Please click “Uninstall” button. 4. Please wait a few seconds to complete uninstallation. 5. Please click “Close” button. 6. Please click “OK” button. 7. Please click “StartProgramsAltair SemiconductorLTE ALT3100HLVUSBUninstall”. 8. Please click “YES (Y)” button. 9. Please reboot your computer after you have completed the uninstallation.
2.2. Installation of drivers 2.2.1. Windows 7 (32 bit) 1. Please double clicks on “Altair(Quanta) Tool Package v1.0.0.exe” to start installation. 2. Please click “Next >” button. 3. Please click “Install” button. 4. It will take a few minutes to complete installation. 5. Please click “Next >” button.
6. Please check “I accept the terms in the license agreement”. 7. Please click “Next >” button. 8. Please select “Full Installation” type. 9. Please click “Next >” button. 10. Please click “Next >” button.
11. Please click “Install” button. 12. Please click “Next >” button. 13. Please click “Finish” button.
14. Please click “Next >” button. 15. Please check “I accept the terms in the license agreement”. 16. Please click “Next >” button. 17. Please click “Install” button.
18. Please click “Continue to install driver anyway (I)”. 19. Please click “Continue to install driver anyway (I)”. 20. Please click “Continue to install driver anyway (I)”. 21. Please click “Continue to install driver anyway (I)”. 22. Please un-check “Launch “Hostless Image Burn””. 23. Please click “Finish” button to complete driver installation. 24. Please click “OK” button. 25. Please click “Finish” button.
26. Please plug in Quanta device and please be patient and wait a few minutes to complete driver installation. 27. Please click “Close (C)” button. 28. Please reset Quanta device (take out and plug in the usb cable), it will take about 50 seconds for Quanta embedded system to be ready.
3. Operation of Connection Manager 3.1. Windows 7 (32 bit) 3.1.1. Basic Configuration 1. In order to get information from our embedded connection manager, it’s mandatory to configure as the following instructions. 2. Please click StartProgramsAltair SemiconductorLTE ALT3100Connection Manager. 3. Please right click on top of connection manager and select OptionsDevice LocationTechnician PC. 4. Connection manager will pop out window for you to enter IP and port. 5. Please enter IP address “10.
7. Please check if connection manager shows device information correctly and the red Altair logo turns into yellow color.
3.1.2. Extended Information 1. Please right click on top of connection manager and select ViewExtended Information. 2. Connection manager will pop out “Extended Information” window. 3. It’s NOT mandatory to set up this “Configuration” tab, connection manager will scan all the supported frequency bands and try to connect to the network.
4. The “Extended Data” tab shows information of Connection Status, APN, Transmission mode, Bandwidth, DL EARFCN, Band, PLMN and Physical Cell ID and so on. 5. The “At Commands” tab will allow you to send AT Commands sets to configure supported functional parameters or to get supported information you want.
3.1.3. LTE Manager 1. Please right click on top of connection manager and select ViewLTE Manager. 2. Connection manager will pop out a “Supervisor Password” window. 3. Please input “123456” and click “OK” button. 4. It will pop out a “LTE Manager” window. 5. LTE Manager shows information about GeneralInfo, LogCreator, Dispatcher, Relay, and GPS Tool.
3.1.4. Manual PLMN 1. Please right click on top of connection manager and select Manual PLMN. 2. Connection manager will pop out a “Plmn Search” window. 3. It’s not necessary for you to select PLMN manually if you want to connect to network.
3.1.5. Change to Commercial Mode 1. Please right click on top of connection manager and select “Change to Commercial Mode”. 2. Connection manager will pop out a “User Mode Changed” dialog. 3. Please click “YES (Y)” button. 4. Please wait a few seconds for device to be ready.
3.1.6. Disable Polling 1. Please right click on top of connection manager and select “OptionsDisable Polling”. 2. Connection manager will stop searching for available network.
3.1.7. PIN Management 1. Please right click on top of connection manager and select “OptionsPIN ManagementPIN Information” to get PIN information. 2. Connection manager will pop out “PIN Information” window. 3. Please click “OK” button. 4. You also can enable PIN usage by right click on top of connection manager and select “OptionsPIN ManagementEnable PIN Usage”. 5. Please input correct PIN code and click “OK” button.
3.1.8. Automatic Connect Mode 1. Please right click on top of connection manager and select “OptionsAutomatic Connect Mode” to switch connection manager from manual connect mode to automatic connect mode. 2. Connection manager will automatically connect to network.
3.1.9. Device Location 1. For Quanta hostless device, please use “Technician PC” only. 2. Please right click on top of connection manager and select “OptionsDevice LocationTechnician PC”. 3. Please set IP address to “10.0.0.1” and click “OK” button. 4. Connection manager will get information from Quanta hostless device.
3.1.10. 1. Help Please right click on top of connection manager and select “HelpAbout”. 2. Connection manager will pop out a “LTE Card Info” message box. 3. It will show information of IMSI number, IMEI number, Supported Bands, Current firmware version, and System package version. 4. Please click “OK” button. 5. Please right click on top of connection manager and select “HelpShow Versions”. 6. Connection manager will pop out a “Version info” message box. 7.
3.1.11. 1. Reset Please right click on top of connection manager and select “Reset”. 2. Connection manager will pop out a “” message box.
Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules.
This device is intended only for OEM integrators under the following conditions: (1) The antenna must be installed such that 20 cm is maintained between the antenna and users, (2) The transmitter module may not be co‐located with any other transmitter or antenna except as described below.