Installation Instructions

ManualsBrandsQuanta Computer ManualsElectronicsRouter

Step 3: Set up the 4G LTE Mount for Canary Flex™ in the Canary app.

Visit canary.is/app on your iOS or Android device for instructions on setting up

your 4G LTE Mount with your Canary Flex.

Step 4: Place your Canary Flex™ inside the main unit.

The magnet inside of the main unit will grab the Canary Flex as you place it

inside of your unit. Tilt the Canary Flex into place. You will need access to the

button on the back of the Canary Flex during the setup process for the 4G

LTE Mount, so do not place your Canary Flex into the main unit until you have

completed the setup process for the 4G LTE Mount in the Canary app

Once the device is placed in the mount, you will be able to charge both the

Canary Flex and the 4G LTE Mount with the same plug

Welcome to your 4G LTE Mount

for Canary Flex™—connected by

Verizon Wireless

Installation Guide

In the box

1 4G LTE Mount for Canary Flex

1 AC power adapter with 13 ft cable

1 hex tool

Verizon Wireless 4G LTE

SIM card (pre-installed)

5 wall mounting screws

5 wall mounting anchors

2 cover screws

1 security screw

1 baseplate

What you’ll need

Phillips screwdriver

Drill

Step 5: Join the cover to the main unit.

Push the cover into place over the Canary Flex. Use the hex tool to screw

the cover screws to the cover to the main unit--one screw on the top

tab, another on the bottom.

Please note, the smaller ‘tab’ goes on the bottom, and the larger one

(with speaker holes) goes on top.

Top Bottom

Installation instructions

IMPORTANT: In order to set up your 4G LTE Mount for Canary Flex™, you will

need to install the Canary app, available from canary.is/app on your iOS or

Android device.

Step 1: Remove the cover from the main unit.

Please note the cover comes attached to the main unit, without screws. To

remove, pinch the top and bottom of the unit and the cover will slide o easily.

Step 2: Charge the 4G LTE Mount

Plug the included AC power adapter for the 4G LTE Mount into any 100-240V

wall outlet to charge the long-life lithium-ion battery. It will take approximately

7-8 hours for your 4G LTE Mount to fully charge when it is powered o (longer

if it’s in use).

Overview of components

Cover Screw

Speaker Hole

Foot/base

Front LED

Middle LED

Rear LED

SIM Card Door

Activiation QR Code

Charging connector

Step 6: Install the baseplate.

For installation onto a wall or other vertical surface: Ensure that the baseplate

hooks are facing up. Hold the baseplate against the installation surface (for

example, your wall or fence) and use a pencil to make three marks through the

three holes in the back of the baseplate. On the pencil marks, drill three pilot

holes into the installation surface.

Note: If wall anchors are required for your installation (drywall, brick, concrete),

use a 1/4” drill bit to drill pilot holes in the installation surface.

If wall anchors are not required for your installation (wood), use a 3/32” drill bit to

drill pilot holes in the installation surface.

Align the baseplate holes with the pilot holes in the installation surface and

install the provided wall anchors (optional) and wall mounting screws.

FPO FPO

FPO

This side up

Installation and Usage Guide

Summary of content (2 pages)

PAGE 1
Welcome to your 4G LTE Mount for Canary Flex™—connected by Verizon Wireless Overview of components FPO Charging connector Installation Guide Installation instructions Step 3: Set up the 4G LTE Mount for Canary Flex™ in the Canary app. Step 5: Join the cover to the main unit. Step 6: Install the baseplate. IMPORTANT: In order to set up your 4G LTE Mount for Canary Flex™, you will Visit canary.
PAGE 2
For use on a tabletop or other flat surface: Baseplate usage is Step 8: Route the cable if opting for plugged in use. Step 10: Secure the 4G LTE Mount foot to the baseplate optional--you may simply place the device on the flat surface. If If planning to use the device with outlet power, route the cable and complete installation.