TM OWNER INSTALLATION AND USER MANUAL Series 3000 Models 3214, 3314, 3316 & 3414 Automatic Garage Door Opener For Sectional Overhead Residential Doors Only DO NOT USE ON ONE PIECE DOORS Before Starting Installation Read all Instructions Thoroughly to Familiarize Yourself with All Aspects of Installation and Adjustment! DOOR AND OPENER WILL NOT OPERATE PROPERLY UNTIL INFRARED SAFETY SENSORS ARE INSTALLED AND PROPERLY ADJUSTED! DO NOT OPERATE DOOR OPENER UNTIL FULLY INSTALLED, ADJUSTED & INSTRUCTED TO DO SO
Read These Important Safety Rules Before Proceeding This symbol indicates caution and appears throughout this instruction manual. This garage door opener is designed and tested to offer reasonably safe operation if installation is followed in strict accordance with these safety instructions. Failure to comply with these instructions may result in serious personal injury or property damage.
Veuillez lire ces règles de sécurité importantes avant de commencer les travaux Ce symbole vous demande de prendre les précautions voulues. Vous le trouverez d’un bout à l’autre du présent guide d’installation. Cet ouvre porte de garage a été conçu et essaye pour vous offrir un fonctionnement sécuritaire dans la mesure ou les directives d’installation sont respectées conformément a ces mesures de sécurité.
Automatic Garage Door Opener – For Residential Doors Only FEATURES 7. Safety System: Independent up and down force adjustments. When properly adjusted, the safety system will automatically reverse when obstructed in down direction and return to fully open position. The door will stop when obstructed in the up direction. See Adj. #2, pg 22. 1. Open and Close Cycle Control: Allows garage door to be started and stopped by push button, transmitter or wall station.
Door Tests Before Starting Before you begin, complete the following two tests to insure that the door is balanced and working properly. A door that binds, sticks or is out of balance could cause severe injury. Do not attempt to compensate for an improperly adjusted door by the installation of an opener. This will interfere with the proper operation of the opener mechanism and/or may damage the door.
INSTALLATION INSTRUCTIONS Step 1: Attaching Motor Power Head Unit to Rail Before assembly, align sprocket/coupling cogs to match notches of driver gear. Rotate the Motor Spline to position Driver Gear so that the nearest notch in Driver Gear is directly behind Motor Spline, as illustrated. Note: Do not rotate more than ½ turn. Place opposite end of rail on temporary support approximately 6” in height.
Step 3: Attach Unit to Front Wall Bracket Raise the front end of the opener and attach it to the front wall bracket, using the ¼” x 4” hex head bolt and the supplied ¼” plastic insert nut. Take care not to over tighten nut; tighten only until end of bolt is flush with outside of nut. NOTE: If you have a torsion spring counterbalance system, it will be necessary to raise the motor Head Assembly of the opener and support it on a step-ladder to attach the front end of the opener to Wall Bracket.
Step 6: Mounting Door Bracket Fiberglass, aluminum and steel doors must be reinforced to prevent damage to the door. Check with your garage door manufacturer for their recommendations. Reinforce light weight doors, as illustrated. For wood doors, mount door bracket, using two 1/4”-20 x 2” carriage bolts and 1/4” nuts supplied, on center line of door with middle hole in line with top rollers.
Step 9: Installing Deluxe Wireless Wall Station (if included) Install all wall controls out of the reach of children and in a location where the door can be seen before activating. Do not mount push buttons near or next to garage door. Locate a convenient place to mount wall station. To keep wall station out of the reach of children, measure at least five feet up from the floor and secure wall station base into wood wall framing using (2) Phillips head screws. Pilot drill mounting holes using a 3/32" bit.
Step 12: Install Wireless Infrared Safety Sensors Wall Mounting Bracket (If Included) Select a mounting position 5 inches above the floor to center line of wall bracket. The EMITTER and TRANSPONDER units must be mounted inside the door opening to minimize any interference by the sun; however, the sensors must be mounted against the door track. The brackets may be temporarily mounted to the wall (or jamb) with a #8 X1/2” screw provided and should be in contact with the door track.
Step 15: Install Wired Infrared Safety Sensor Wall Mounting Brackets Use the following instructions if your opener is equipped with Wired Infrared Safety Sensors. If you just installed the Wireless Infrared Safety Sensors go to step 20. Select a mounting position 5 inches above the floor to center line of wall bracket. The sending and receiving units should be mounted inside the door opening to minimize any interference by the sun.
Step 17: Install Wiring for Wired Infrared Safety Sensor Identify which side of the garage door opening (if any) the sun is “likely” to shine on to. Since sunlight may affect infrared safety sensors, you should mount the sending unit on the side of the door opening exposed to the sun. Uncoil the wires from the infrared safety sensors and route the wire up the garage wall across the ceiling and down to the back of the power head, as illustrated. Tack the wires in place using staples.
Step 19: Mount Wired Infrared Safety Sensors Attach the sending and receiving units to the “U” brackets by inserting their tabs into their respective holes. Step 20: Connecting Electrical Power To reduce the risk of electrical shock, connect the power cord only to a properly grounded 3 prong, 120 volt outlet. Do not use an extension cord or change the plug in any way. At this point, plug in the opener to an electrical outlet.
Step 21: Wireless Wall Station Security Code Change and Programming Note: The following steps describe the process to change the Wireless Wall Station security code and to program the Wireless Wall Station to the opener. IMPORTANT: You MUST change the Wireless Wall Station security code prior to programming the device to the power head unit. WARNING: During programming the garage door may operate. Keep people and objects clear of the moving door to prevent door damage or possible personal injury.
Step 22: Alignment of the Wireless Infrared Safety Sensors Use the following instructions if your opener is equipped with Wireless Infrared Safety Sensors. If your opener is equipped with Wired Infrared Safety Sensors proceed to step 23. IMPORTANT: This infrared beam sensor sends an invisible beam of light from the emitter unit to the transponder unit across from the pathway of the door. The door opener will not operate until the safety sensor is programmed to the power head and it is properly aligned.
Step 23: Alignment of the Wired Infrared Safety Sensors Use the following instructions if your opener is equipped with Wired Infrared Safety Sensors. Otherwise proceed to step 24. IMPORTANT: This infrared beam sensor sends an invisible beam of light from the sending unit to the receiver unit across from the pathway of the door. The door opener will not operate until the safety sensor is connected to the power head and properly aligned.
Programming Transmitter to Power Head Unit Note: Do not press any button on the Transmitter until instructed 1. Press the PROGRAM Switch button located on the garage door power head unit once. The red PROGRAM STATUS light on the motor power head unit and overhead lamp will turn on and remain lit for one minute, indicating that it is ready to learn the Transmitter. 2. Press the button on the Transmitter you wish to use to operate the door.
Step 27: Connecting Door Arm to Door Door Mounted Bracket Visually align cushion arm connecting hole with middle hole of door bracket by rotating tube section in appropriate direction. Release trolley (cushion arm attached) with manual release cord and pull trolley a few inches toward motor. Now rotate cushion arm tube section 2 turns counterclockwise to provide a cushion when door is closed or encounters an obstruction. Align connecting hole in cushion arm to middle hole in door bracket; insert 3/8” dia.
Step 29: Setting Door Opening Travel Do not use adjustments to compensate for a poorly balanced door. This will interfere with the proper operation of the travel adjustments and may damage door. The door opener is assembled with the open travel adjustment preset for a typical door, but all doors should be adjusted to stop as close as possible to the door’s “natural” fully open, resting position.
Step 31: Programming Wireless Keyless Entry (If Included) NOTE: To facilitate installation, program the Keyless Entry station to the opener before mounting to wall. WARNING: During programming the garage door may operate. Keep people and objects clear of the moving door to prevent door damage or possible personal injury. NOTE: Before programming ensure garage door is in the “down” position. 1. Press the PROGRAM Switch button located on the garage door power head unit once.
ADJUSTMENTS Adjustment # 1 Opening and Closing Force This garage door opener is built with a safety system that allows the door to reverse in the close direction and stop in the open direction. This must be adjusted so your opener does not use excessive force in the down direction or react to the weight of the door during upward travel. CLOSING FORCE ADJUSTMENT To help determine that the closing door force is not excessive, grasp the door handle or bottom edge during downward travel.
Adjustment # 2 Contact Obstruction Sensing (Closing Direction) The opener is designed to automatically reverse the door during closing travel whenever it comes in contact with an object up to the last 1 inch of travel above the floor. An object on the floor with a height less than 1” will cause the door to stop. (Test according to instructions on Step 30.
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of severe injury of death: Before you proceed, please thoroughly read the safety rules on page 2 and the following operating instructions. Operate only when opener is properly adjusted and the door is visible and unobstructed. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. If possible, use the emergency release only when the door is closed. Use caution when using this release with the door open.
Operation of Your Opener HOW TO ACTIVATE THE OPENER Never let children operate or play with door controls. Keep remote control away from children. Use any of the following devices: 1. The Remote Control Transmitter; momentary push of the button and the door will start to move. 2. The Wall Station Up/Down button; push momentarily the button until the door starts to move. Constant push of the button, until door is closed is required if light flashes (indicating a Safety Sensor obstruction). 3.
HOW TO OPERATE THE WIRELESS WALL STATION (If Included) Never let children operate or play with door controls. Keep remote control away from children. The Wireless Wall Station Provides the Following Features: 1. Momentarily pressing the UP/DOWN button activates the door. An open door will close and a closed door will open. 2. Momentarily pressing the LIGHT button will toggle the overhead light on and off. The light will remain on until it is turned off by another LIGHT button press or the door is activated.
HOW TO OPERATE THE DOOR MANUALLY – Emergency Release Disconnect The door should be fully closed if possible, weak or broken springs could allow an open door to fall rapidly. Property damage or serious personal injury could result. Do not use the manual release knob to pull the door open or closed. Do not stand near or in the path of door when using the emergency release disconnect.
MAINTENANCE OF YOUR OPENER SYSTEM Test door opener monthly. The garage door MUST reverse on contact with a 1 inch high solid test object on the floor. If adjusting either the force or the limit of travel, retest the door opener. Failure to adjust the opener properly may cause severe injury of death. KEEP GARAGE DOORS PROPERLY BALANCED. See owner’s manual. An improperly balanced door could cause severe injury or death.
TROUBLE SHOOTING SECTION SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Opener won’t work from wall button or radio control. No power to opener. Check cord to outlet, wall switch and circuit breaker. Short circuit in wires to opener or wall button. Isolate by disconnecting the wires at the opener from the wall station. Motor Protector trips open due to excessive use. Radio control system non-operational. Allow motor to cool for 20 minutes and try again. Weak or dead battery in transmitterreplace.
Parts Breakdown Rail Assembly – All Models 29
Parts Breakdown Power Head Assembly – All Models #. Part # Description Per Unit #. Part # Description # Per Unit 1. 2. 3. 157167 292123 306137 1 1 1 17. 18. 18a. 157496 157166 157159 306364 260570 306486 269025 260552 252994 252993 1 1 1 1 1 1 1 19. 19a 20. 20a 21. 21a 22. 157165 157162 250597 260598 260600 260599 252092 2 2 1 1 1 1 1 11. 12. 13. 14. 15. 16.
QUANTUM ACCESSORIES Three Button mini/visor Transmitter Part#302083 Controls up to 6 doors or wireless accessories. Includes visor clip. Wired Deluxe Wall Station Part# Allows independent door up/down control and overhead light on/off control. Unit will fit over a standard electrical outlet box. Wireless Deluxe Wall Station Part#302090 Completely wireless unit with independent door up/down control, light on/off control, custom pet opening, delay exit timer, and program button.
Questions? For quick answers and helpful advice, Call Toll Free 1-800-305-4349 LIMITED LIFETIME WARRANTY The Manufacturer warrants that the Quantum™ garage door opener will be free from defects in materials and workmanship for a period of five years (3214, 3314), ten years (3316), and fifteen years (3414). Electronic components are warranted for three years (3214, 3314) and five years (3316, 3414).