QUANTUM 610 S E R I E S INNOVATIVE REHAB SOLUTIONS Including Models: Quantum 610 2S, Quantum 610 2SP, Quantum 610 2MP 1-800-800-8586 (US) 1-888-570-1113 (Canada)
SAFETY GUIDELINES WARNING! A Quantum Rehab Specialist or a qualified technician must perform the initial setup of this power chair and must perform all of the procedures in this manual. The symbols below are used throughout this owner's manual and on the power chair to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/situation.
CONTENTS I. INTRODUCTION.................................................................................................................................... 4 II. SAFETY .................................................................................................................................................... 6 III. YOUR POWER CHAIR ....................................................................................................................... 18 IV. ASSEMBLY.............................
I. INTRODUCTION SAFETY WELCOME to Quantum Rehab, a division of Pride Mobility Products Corporation (Pride). The power chair you have purchased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident that these design features will provide you with the conveniences you expect during your daily activities. Once you understand how to safely operate and care for your power chair, it should give you years of trouble free operation and service.
I. INTRODUCTION PRIDE OWNERS CLUB As an owner of a Pride product, you are encouraged to enroll in the Pride Owners Club. Complete and return your enclosed product registration card or visit Pride’s web site at www.pridemobility.com. From our home page, select “Owners Club” to enter a page dedicated to current and potential Pride product owners. You will gain access to interviews, stories, recreation ideas, daily living tips, product and funding information, and interactive message boards.
II. SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. Read and follow the information in the owner’s manual. Do not allow unsupervised children to play near the power chair while the batteries are charging. Maximum seating weight. Keep your hands away from the tires when driving.
II. SAFETY Do not lift the mobility vehicle while seated in it. Do not lift the mobility vehicle while seated in it. Do not connect an extension cord to the AC/DC converter or the battery charger. Removal of grounding prong can create electrical hazard. If necessary, properly install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access. Wear safety goggles. Corrosive chemicals contained in battery. Quantum 610 Series www.quantumrehab.
II. SAFETY EMI-RFI - This product has been tested and passed at an immunity level of 20 V/m. Explosive conditions exist! Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive conditions. Keep tools and other metal objects away from battery terminals.
II. SAFETY Battery charger for indoor use only. Disposal and recycling - Contact your Quantum Rehab Specialist for information on proper disposal and recycling of your Pride product and its packaging. Disposal and recycling - Contact your Quantum Rehab Specialist for information on proper disposal and recycling of your Pride product and its packaging. Locked and in drive mode.
II. SAFETY GENERAL GUIDELINES MANDATORY! Do not operate your new power chair for the first time without completely reading and understanding this owner’s manual. Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive variety of products to best fit the individual needs of the power chair user.
II. SAFETY Weight Limitations Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit. MANDATORY! Stay within the specified weight capacity of your power chair. Exceeding the weight capacity voids your warranty. Pride will not be held responsible for injuries and/or property damage resulting from failure to observe weight limitations. WARNING! Do not carry passengers on your power chair.
II. SAFETY WARNING! Even though your power chair is capable of climbing slopes greater than those illustrated in figure 1, do not, under any circumstances, exceed the incline guidelines or any other specifications presented in this manual. Doing so could cause instability in your power chair. In compliance with the Americans with Disabilities Act of 1990, all handicap public access ramps are required to have a maximum slope of 5° (8.7%).
II. SAFETY Public Streets and Roadways WARNING! You should not operate your power chair on public streets and roadways. Be aware that it may be difficult for traffic to see you when you are seated on your power chair. Obey all local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with extreme caution.
II. SAFETY Stairs and Escalators Power chairs are not designed to travel up or down stairs or escalators. Always use an elevator. WARNING! Never use your power chair to negotiate steps or escalators. Doors ! Determine if the door opens toward or away from you. ! Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently and slowly backward to pull the door open.
II. SAFETY Batteries In addition to following the warnings below, be sure to comply with all other battery handling information. For more information about your power chair’s batteries, see VI. “Batteries and Charging.” MANDATORY! Battery posts, terminals, and related accessories contain lead and lead compounds. Wear goggles and gloves when handling batteries and wash hands after handling. WARNING! Power chair batteries are heavy. See specifications table.
II. SAFETY Transfers Transferring onto and off of your power chair requires a good sense of balance. Always have an attendant or healthcare professional present while learning to properly transfer yourself. To eliminate the possibility of injury, Pride recommends that you or a trained attendant perform the following tasks before attempting a transfer: ! Turn off the power to the controller. ! Ensure your power chair is not in freewheel mode. See III. “Your Power Chair.
II. SAFETY WARNING! Pride strongly recommends that you do not smoke cigarettes while seated in your power chair, although the power chair has passed the necessary testing requirements for cigarette smoking. You must adhere to the following safety guidelines if you decide to smoke cigarettes while seated in your power chair. ! Do not leave lit cigarettes unattended. ! Keep ashtrays a safe distance from the seat cushions. ! Always make sure cigarettes are completely extinguished before disposal.
III. YOUR POWER CHAIR THE QUANTUM 610 The Quantum 610 Series has two main assemblies: the seat assembly and the power base assembly. See figure 5. Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/ brake assemblies, two drive wheels, four caster wheels, two batteries, and wiring harnesses. See figure 5, 6, and 7.
III. YOUR POWER CHAIR QUANTUM 610 SPECIFICATIONS Suspension: Active-Trac Extreme (ATX) Drive Wheels: 10 in. (25.4 cm), pneumatic and solid available Front Caster Wheels: 5 in. (12.7 cm), solid Rear Caster Wheels: 6 in. (15.24 cm), solid Maximum Speed:¹ Up to 4.5 mph (7.24 km/h) Range:¹ Up to 25 miles (40.23 km) Brakes: “Intelligent Braking” electronic regenerative, disc park brake Ground Clearance:² 2.5 in. (6.35 cm) Turning Radius:² 21.25 in. (53.98 cm) Overall Size:² Length: 39 in.
III. YOUR POWER CHAIR REAR SHROUD FASTENER TRAPEZE BARS FRONT COVER MOTOR/BRAKE ASSEMBLY Figure 6. The Quantum 610 Series Power Base Electrical Components The electrical components are located inside the power base. The ammeter and the charger power cord receptacle for the optional onboard charger are located on the right side of the power base. The main circuit breaker is located on the front of the battery tray. The controller connector(s) are located inside the power base. See figure 7.
III. YOUR POWER CHAIR Battery Connector: This is where the controller connects to the batteries. Charger Inhibit Connector (optional onboard charger only): The charger inhibit enables the onboard battery charger to disable the controller during charging. Controller Connector: This is where the controller connects to the power base. Main Circuit Breaker: The main circuit breaker is a safety feature built into your power chair. When the batteries and the motors are heavily strained (e.g.
III. YOUR POWER CHAIR Manual Freewheel Levers Your power chair has a manual freewheel lever on each motor. Manual freewheel levers enable you to disengage the drive motors from the gearboxes and maneuver the chair manually. WARNING! Do not use the power chair while the drive motors are disengaged! Do not disengage the drive motors when the power chair is on an incline, as the unit could roll on its own! Only engage the freewheel mode when on a level surface.
I V. ASSEMBLY INITIAL ASSEMBLY Your power chair may require some assembly either before initial use or after transportation. It may also require disassembly to make some comfort adjustments. Figure 10 details those parts of the power chair that are designed to be disassembled and assembled by an end user or by a qualified caregiver before using the product or making comfort adjustments.
I V. ASSEMBLY Seat Installation It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Most seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be attached to any medium-back or high-back seat, regardless of seat width or seat depth. The two main components are aluminum extrusions mounted to the seat base.
I V. ASSEMBLY Power Seat Option Installation Your power chair may be equipped with the power seat option. While the seat itself may be any one of the styles offered for this model, the way the seat base attaches to the power base is different. WIRE TIES To install the power seat: l. Align the post on the bottom of the power seat base over the hole in the power seat actuator. 2. Slide the post into the actuator and push the friction lock lever forward. 3. Connect the power seat cable to the power base.
V. COMFORT ADJUSTMENTS COMFORT ADJUSTMENTS After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position. If your power chair is equipped with a specialty seat, refer to the information provided in separate manuals. If your power chair is equipped with a medium-back, a high-back, or a reclining seat, refer to the following information.
V. COMFORT ADJUSTMENTS Seat Position You can move the seat forward or rearward by changing the extrusion mounting position. To change the position: 1. Turn off the power to the controller. 2. Unlock the rear shroud fasteners and remove the rear shroud. See figure 6. 3. Unplug the controller connector(s) from the power base. 4. Remove the seat from the power base. 5. Remove both extrusions from the bottom of the seat. 6. Reposition the extrusions on a different set of mounting holes.
V. COMFORT ADJUSTMENTS To change the armrest width: 1. Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 18. 2. Loosen the knobs. 3. Slide the armrests in or out to the desired width. 4. Tighten the knobs. SETSCREW Armrest Angle Adjustment To change the armrest angle: 1. Lift the armrest straight up so that it is perpendicular to the floor. See figure 18. 2. Loosen the jam nuts. 3. Turn the adjusting screw to raise or lower the front of the Figure 19.
V. COMFORT ADJUSTMENTS NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-Balance Power Positioning System, loosen the mounting screws in the mounting block, transfer the mounting block and controller to the opposite armrest, and tighten the mounting screws. See figure 20. Foot Platform Height Adjustment The foot platform height is easily adjusted to different heights. To raise or lower the foot platform: 1. Remove the quick release fasteners from the foot platform bracket.
V. COMFORT ADJUSTMENTS Foot Platform Angle Adjustment You can adjust the angle of the foot platform with a hex key. To adjust the foot platform angle: 1. Flip up the foot platform and locate the setscrew and jam nut. See figure 23. 2. Loosen the jam nut. 3. Turn the setscrew to raise or lower the front of the foot platform. 4. Tighten the jam nut to secure the setscrew.
VI. BATTERIES AND CHARGING BATTERIES AND CHARGING The Quantum 610 uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.
VI. BATTERIES AND CHARGING WARNING! If your battery charger has not been tested and approved for outdoor use, then do not expose it to adverse or extreme weather conditions. If the battery charger is exposed to adverse or extreme weather conditions, then it must be allowed to adjust to the difference in environmental conditions before use indoors. Refer to the manual supplied with the battery charger for more information. To charge the batteries using the off-board charger: 1.
VI. BATTERIES AND CHARGING Frequently Asked Questions (FAQs) How does the charger work? The battery charger takes the standard electrical outlet voltage of 120 VAC (alternating current) and converts it to 24 VDC (direct current). The power chair batteries use direct current to run your power chair. When the battery voltage is low, the charger works harder to charge the battery. As the battery voltage approaches full charge, the charger does not work as hard to complete the charging cycle.
VI. BATTERIES AND CHARGING WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive conditions. Why do my new batteries seem weak? Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium (nicads), or in other common battery types. Deep-cycle batteries are specifically designed to provide power, drain down their charge, and then accept a relatively quick recharge.
VII. CARE AND MAINTENANCE CARE AND MAINTENANCE Your Quantum 610 is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks. You can perform some of these checks, but others require assistance from your Quantum Rehab Specialist. Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that your power chair gives you years of trouble-free operation.
VII. CARE AND MAINTENANCE ! All wheel bearings are prelubricated and sealed. They require no subsequent lubrication. ! The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain its high-gloss appearance. ! Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery tray, with the battery terminals facing inward, toward each other.
VII. CARE AND MAINTENANCE Storage Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries from the power chair. See VI. “Batteries and Charging.” WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be damaged.
VII. CARE AND MAINTENANCE TIRE AXLE KEY REAR RIM HALF TUBE WHEEL HUB AXLE SLOT FRONT RIM HALF NUTS DRIVE DRIVE WHEEL WHEEL NUT WASHER WASHERS Figure 25. Quantum 610 Drive Wheel Figure 26. Quantum 610 Drive Wheel Disassembled Follow these easy steps for a quick and safe repair for both pneumatic and solid tires: 1. Turn off the power to the controller. 2. Set the power chair up on blocks. 3. If you are changing a pneumatic tire, completely deflate it before removing the wheel. 4.
VII. CARE AND MAINTENANCE REAR SHROUD FASTENERS REAR SHROUD BATTERY WIRING DIAGRAM LABEL FRONT BATTERY REAR BATTERY Figure 27. Battery Installation Quantum 610 Series www.quantumrehab.
VII. CARE AND MAINTENANCE To replace the batteries: 1. Turn off the power to the controller. 2. Make sure that the power chair is in drive mode. See III. “Your Power Chair.” 3. Loosen the rear shroud fasteners. 4. Remove the rear shroud. See figure 27. 5. Disconnect the battery harness from the rear battery. 6. Remove the retaining pin and lift off the front cover using the foot platform bracket. See figure 21. 7. Slide the battery tray forward. 8. Disconnect the battery harness from the front battery.
VIII.
VIII. WARRANTY RECONDITIONED UNITS WARRANTY All reconditioned units are covered by a six-month warranty from Pride effective from the date of purchase. WARRANTY EXCLUSIONS This warranty does not extend to those items which may require replacement due to normal wear and tear.
Quality Control - Quantum 610 Series Inclusion of all Parts Joystick Serial Number Controller Serial Number Left Motor Serial Number Right Motor Serial Number Fit and Finish Performance Pride keeps a more detailed report on file at the factory.