Quantum 610 QUANTUM 610 Serial Number
SAFETY GUIDELINES WARNING! A Quantum Rehab Provider or a qualified technician must perform the initial setup of this power chair and must perform all of the procedures in this manual. The symbols below are used throughout this owner's manual and on the power chair to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/situation.
CONTENTS I. INTRODUCTION ................................................................................................................................. 4 II. SAFETY .................................................................................................................................................. 5 III. YOUR POWER CHAIR ...................................................................................................................... 7 IV. ASSEMBLY ...................................
I. INTRODUCTION SAFETY WELCOME to Quantum Rehab, a division of Pride Mobility Products (Pride). The power chair you have purchased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident that these design features will provide you with the conveniences you expect during your daily activities. Once you understand how to safely operate and care for your power chair, it should give you years of trouble-free operation and service.
II. SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. NOTE: There are more warnings identified and explained in the Consumer Safety Guide that is included with your power chair. Please become familiar with all the warnings and safety information found in the Consumer Safety Guide and refer to this resource often.
II. SAFETY GENERAL GUIDELINES MANDATORY! Do not operate your new power chair for the first time without completely reading and understanding this owner’s manual. Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive variety of products to best fit the individual needs of the power chair user.
III. YOUR POWER CHAIR THE QUANTUM 610 The Quantum 610 has two main assemblies: the seat assembly and the power base assembly. See figure 1. Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/brake assemblies, two drive wheels, four caster wheels, two batteries, and wiring harnesses. See figure 1, 2, and 3.
III. YOUR POWER CHAIR REAR SHROUD FASTENER TRAPEZE BARS FRONT COVER MOTOR/BRAKE ASSEMBLY Figure 2. The Quantum 610 Series Power Base Electrical Components The electrical components are located inside the power base. The main circuit breaker is located on the front of the battery tray. The controller connector(s) are located inside the power base. See figure 3. Motor Connectors: This is where the controller connects to the motors. Battery Connector: This is where the controller connects to the batteries.
III. YOUR POWER CHAIR Main Circuit Breaker: The main circuit breaker is a safety feature built into your power chair. When the batteries and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to the motors and the electronics. If the circuit trips, allow your power chair to “rest” for approximately one minute. Next, push in the circuit breaker button, turn on the controller, and continue normal operation.
III. YOUR POWER CHAIR Manual Freewheel Levers Your power chair has a manual freewheel lever on each motor. Manual freewheel levers enable you to disengage the drive motors from the gearboxes and maneuver the chair manually. WARNING! Do not use the power chair while the drive motors are disengaged! Do not disengage the drive motors when the power chair is on an incline, as the unit could roll on its own! Only engage the freewheel mode when on a level surface.
IV. ASSEMBLY INITIAL ASSEMBLY Your power chair may require some assembly either before initial use or after transportation. It may also require disassembly to make some comfort adjustments. Figure 6 details those parts of the power chair that are designed to be disassembled and assembled by an end user or by a qualified caregiver before using the product or making comfort adjustments.
IV. ASSEMBLY Seat Installation It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Most seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be attached to any mediumback or high-back seat, regardless of seat width or seat depth. The two main components are aluminum extrusions mounted to the seat base.
IV. ASSEMBLY Power Seat Option Installation Your power chair may be equipped with the power seat option. While the seat itself may be any one of the styles offered for this model, the way the seat base attaches to the power base is different. To install the power seat: l. Align the post on the bottom of the power seat base over the hole in the power seat actuator. 2. Slide the post into the actuator and push the friction lock lever forward. 3. Connect the power seat cable to the power base. 4.
V. COMFORT ADJUSTMENTS COMFORT ADJUSTMENTS After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position. If your power chair is equipped with power positioning options, refer to the information supplied in supplemental manuals or contact your Quantum Rehab Provider.
V. COMFORT ADJUSTMENTS Seat Position You can move the seat forward or rearward by changing the extrusion mounting position. To change the position: 1. Turn off the power to the controller. 2. Loosen the rear shroud fasteners and remove the rear shroud. See figure 2. 3. Unplug the controller connector(s) from the power base. 4. Remove the seat from the power base. 5. Remove both extrusions from the bottom of the seat. 6. Reposition the extrusions on a different set of mounting holes.
V. COMFORT ADJUSTMENTS To change the armrest width: 1. Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 14. 2. Loosen the knobs. 3. Slide the armrests in or out to the desired width. 4. Tighten the knobs. Armrest Angle Adjustment To change the armrest angle: 1. Lift the armrest straight up so that it is perpendicular to the floor. See figure 14. 2. Loosen the jam nuts. 3. Turn the adjusting screw to raise or lower the front of the armrest. 4.
V. COMFORT ADJUSTMENTS Foot Platform Height Adjustment The foot platform height is easily adjusted to different heights. To raise or lower the foot platform: 1. Remove the quick release fasteners from the foot platform bracket. See figure 16. 2. Loosen the foot platform securement nut one-half turn. 3. Raise or lower the foot platform to the desired height. 4. Reinstall the quick release fasteners into the foot platform bracket and tighten. 5. Tighten the nut to secure.
V. COMFORT ADJUSTMENTS Positioning Belt Your power chair may be equipped with a positioning belt that can be adjusted for operator comfort. See figure 19. The positioning belt is designed to support the operator so that he/ she does not slide down or forward in the seat. The positioning belt is not designed for use as a restraining device. WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor is your power chair suitable for use as a seat in any vehicle.
V. COMFORT ADJUSTMENTS Power Elevating Seat (Optional) If your power chair is equipped with a power elevating seat, you can change the seat height either through the controller or through a toggle switch mounted to one of the armrests. To change the seat height through toggle switch: 1. Press forward on the toggle switch to raise the seat. See figure 20. 2. Pull back on the toggle switch to lower the seat.
VI. BATTERIES AND CHARGING BATTERIES AND CHARGING The Quantum 610 uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.
VI. BATTERIES AND CHARGING To charge the batteries using the off-board charger: 1. Position the front of your power chair next to a standard electrical outlet. 2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power Chair.” 3. Plug the off-board charger into the off-board charger/ programming socket on the controller. See figure 21. 4. Plug the off-board charger into the electrical outlet.
VI. BATTERIES AND CHARGING How often must I charge the batteries? Many factors come into play when deciding how often to charge the batteries. You may use your power chair all day on a daily basis or you may not use it for weeks at a time. Daily Use If you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power chair. Your power chair will be ready each morning to give you a full day’s service.
VI. BATTERIES AND CHARGING It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature. More importantly, it will take a few “charging cycles” (a partial drain—then a full recharge) to establish the critical chemical balance that is essential to the battery’s peak performance and long life. It will be well worth it to take the time to break in your battery properly.
VII. CARE AND MAINTENANCE CARE AND MAINTENANCE Your Quantum 610 is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks. You can perform some of these checks, but others require assistance from your Quantum Rehab Provider. Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that your power chair gives you years of trouble-free operation.
VII. CARE AND MAINTENANCE All wheel bearings are prelubricated and sealed. They require no subsequent lubrication. The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain its high-gloss appearance. Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery tray, with the battery terminals facing inward, toward each other.
VII. CARE AND MAINTENANCE Storage Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries from the power chair. See VI. “Batteries and Charging.” WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be damaged.
VII. CARE AND MAINTENANCE TIRE AXLE KEY REAR RIM HALF TUBE AXLE SLOT FRONT RIM HALF WHEEL HUB NUTS DRIVE WHEEL NUT DRIVE WHEEL WASHER WASHERS Figure 22. Quantum 610 Drive Wheel Figure 23. Quantum 610 Drive Wheel Disassembled Follow these easy steps for a quick and safe repair for both pneumatic and solid tires: 1. Turn off the power to the controller. 2. Set the power chair up on blocks. 3. If you are changing a pneumatic tire, completely deflate it before removing the wheel. 4.
VII. CARE AND MAINTENANCE PROHIBITED! Keep tools and other metal objects away from the battery terminals. Contact with tools can cause electrical shock. You may need the following to change your batteries: metric/standard socket set and ratchet adjustable wrench To replace the batteries: 1. Turn off the power to the controller. 2. Make sure that the power chair is in drive mode. See III. “Your Power Chair.” 3. Loosen the rear shroud fasteners. 4. Remove the rear shroud. See figure 24. 5.
VII. CARE AND MAINTENANCE Battery Set Configuration: + = Positive (Red) Terminal Post - = Negative (Black) Terminal Post Connect Red wires to Red Positive (+) Terminal Posts. Connect Black wires to Black Negative (–) Terminal Posts. REAR SHROUD FASTENERS REAR SHROUD BATTERY WIRING DIAGRAM LABEL FRONT BATTERY REAR BATTERY Figure 24. Battery Installation Quantum 610 Series www.pridemobility.
NOTES 30 www.pridemobility.
SAFETY GUIDELINES WARNING! A Quantum Rehab Provider or a qualified technician must perform the initial setup of this power chair and must perform all of the procedures in this manual. The symbols below are used throughout this owner's manual and on the power chair to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/situation.
Quantum 610 QUANTUM 610 Serial Number
