Installation and User manual QNVR Quantum IP Network Video Recorder
QNVR installation and user manual 2 QNVR Installation Manual V1.
QNVR installation and user manual CE Information The product must be installed according to the currently valid installation regulat ions for EMC to guarantee the designed use and to prevent EMC problems. The device supplied with this manual meets the requirements of the following E C Directives: EMC: 2004/108/EC, LVD : 2006/95/EC and RoHS: 2011/65/EU WARNING This is a Class A product.
QNVR installation and user manual 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use the attachments/accessories specified by the manufacturer. 12) Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
QNVR installation and user manual Contents OVERVIEW ........................................................................................................................... 7 1. CONTENTS OF PACKING .................................................................................................... 7 2. FEATURES ....................................................................................................................... 8 INSTALLATION ............................................................
QNVR installation and user manual 4-2. NTP ........................................................................................................................................................ 48 5. EVENT ............................................................................................................................49 5-1. E-Mail Registration ................................................................................................................................. 49 5-2. E-mail Out ..
QNVR installation and user manual Overview 1. Contents of Packing User Manual Mouse Power Cable Remote Controller Installation CD 7 QNVR Installation Manual V1.
QNVR installation and user manual 2. Features ● Convenience - User-friendly GUI (Graphical User Interface) - Easy-to-use menu structure - Easy-to-use recorded data search (Time, Date, Motion, and Alarm) - Easy-to control via Front Panel, IR remote control and USB 2.0 mouse. ● Stability - Auto restart after power interruption - DB structure offers data stabilisation and better storage utilisation ● Expandability - Remote NVR’s can be controlled using the supplied software client viewer.
QNVR installation and user manual Installation 1. Front Panel Controls ①②③④ ⑤ ⑥ ⑦ ⑩⑪⑫ ⑬ ① Volume Up & Down ( / ⑧ ⑨ ⑭ ⑮ ) To increase or decrease the volume. ② Audio Selection Switches through audio channels ③ Multi-screen Display Use the Multi-screen display button to select the display mode (single/4/9/16way). ④ PTZ Channel Selection Used to select the PTZ channel on multi-screen.
QNVR installation and user manual To stop playback and go back to live mode. To eject DVD-RW Pause ( ▌▌) To freeze picture on playback mode and live mode. Forward Play (▶) Playback of the recorded data. When in play mode press again to enter fast forward mode. When video is paused this allows frame forward. Reverse Play / Rewind () Reverse play of recorded data. When in play mode press again to enter fast rewind mode.
QNVR installation and user manual 2.
QNVR installation and user manual ⑦ USB Port USB 2.0 port for mouse, USB storage ⑧ RS232 Port Serial Communication (for service) ⑨ E-SATA Port Port for e-SATA HDD ⑩ PTZ Camera Controller Serial Communication for Pan / Tilt Camera ⑪ Keyboard Controller Serial Communication for P/T/Z Control Keyboard ⑫ Alarm Output Alarm(relay) output port ⑬ Sensor Input 16 Sensor input ports ⑭ AC Power Input AC 100-240V 50/60Hz 12 QNVR Installation Manual V1.
QNVR installation and user manual 3.
QNVR installation and user manual 4. Connection Guide Connecting the monitor There are two available monitor outputs on NVR. ● HDMI output : Connect to the HDMI port of the HD monitor(HDTV). ● VGA output : Connect to the VGA port of the VGA monitor. Connecting to a network Use the Ethernet port to connect to remote PC, IP cameras and NAS via Ethernet network. ● Port for PC Client: Connect to the PC. (Default: 192.168.1.111) ● Port for IP Camera: Connect to IP camera network. (Default: 192.168.30.
QNVR installation and user manual Connecting audio To listen to live or recorded audio, connect to an amplified speaker system. ● Audio output : Connect to the audio in of the audio AMP. Connecting to a sensor input There are 16 individual alarm inputs marked as Sensor In (1-16). Common Common Sensor GND GND Inputs ● Sensor inputs : Connect to (+) terminal of a sensor. ● Common GND : Connect to (–) terminals of sensors.
QNVR installation and user manual Connecting to a remote keyboard (VKBD4) This RS485 connector is for a control keyboard. (+) (-) ● Keyboard (+) : Connect to RS485 Tx(+) of the keyboard. ● Keyboard (-) : Connect to RS485 Tx(-) of the keyboard. Connecting to a mouse ● USB 2.0 : Connect to the mouse. Connecting to a external HDD To expand the HDD capacity, connect the external storage. ● e-SATA : Connect to the e-Sata HDD storage. 5. Turning on the NVR 1. Connect the power cable. 2. Connect camera cables.
QNVR installation and user manual Operation 1. Navigation You can navigate the on screen menus using the front panel buttons, IR remote control or mouse. 1-1. Mouse Control Right clicking the mouse brings up the following popup menu. ① Setup Menu ② Search Menu ③ PAN/Tilt Menu ① ② ③ ⑤ ⑥ ⑧ ⑨ ⑩ ⑪ ④ ④ Focus/Zoom Menu ⑤ Power Button ⑥ Sequence Button ⑦ Playback Button ⑧ Eject Button ⑨ Volume Up/Down Button ⑩ Multi-screen Display Button ⑦ ⑨ ⑪ ⑪ Channel Up/Down Button 1-2.
QNVR installation and user manual 2. Screen Displays 2-1. OSD Description The Status Bar on screen shows HDD capacity, network connection, current time, etc. ① ① HDD capacity: ② ③④⑤⑥ ⑦ Used capacity / Duration ② Multi-screen Display icons : Single/ 4/ 9/ 16way ③ e-SATA connection ④ USB memory connection ⑤ Mouse connection ⑥ Network connection ⑦ Current Date/Time 2-2. Select Channel Use the Multiscreen display button ( Single Channel Live 1ch ) on the popup menu to select the display mode.
QNVR installation and user manual Display switches in the following order when the DIS button is pressed. Single Channel 4 Channel 9 Channel 16 Channel Single Channel 2-3. Digital Zoom When the system is in full-screen mode, drag your mouse in the screen to select a section and then left click mouse to realize digital zoom. You can right click mouse to exit. 19 QNVR Installation Manual V1.
QNVR installation and user manual 3. Playback Click the right button on the mouse, the popup menu will be displayed on screen. To begin playback, press the Play button on the popup menu: 3-1. OSD Description The Control Bar on screen shows Playback control buttons, Progress bar, Display mode buttons, Playback time, etc.
QNVR installation and user manual 3-2. Playback Control Playback When the Play button(⑧) is pressed, the unit will play forward at the rate the data was recorded. While in the play mode, the user may change the playback direction, playback speed. To return to play forward operations, press the Play button(⑧). Reverse Play To begin reverse playback, press the Reverse Play button(⑦). Pause During playback, press the Pause button (⑥). This feature pauses all full screen and multiscreen images.
QNVR installation and user manual 3-3. Playback Search The user can search the recorded video during playback. The recorded video is indicated by a colour bar on the time bar(②). You can use the Previous/ Next time buttons(①) to view if there are more recorded data. Click the mouse at the desired point of the colour bar, you can view the recorded data. For more advanced search modes see “Search Menu” section page 48 22 QNVR Installation Manual V1.
QNVR installation and user manual 4. PTZ Control via RS485 The user can control PTZ cameras via RS485 communication. The PTZ domes can be wired in a Daisy chain. Daisy Chain configuration The telemetry function of NVR can be controlled via 4 different methods: 1. Mouse 2. Remote keyboard 3. Remote controller 4. Software viewer 4-1. PTZ Control by mouse 1. Click the right button the mouse, the popup menu will appear. 2. To control Pan/Tilt, click the P/T icon(①).
QNVR installation and user manual ① Multiscreen Display : Changing the display mode ② PTZ Camera Selection ③ Set Preset ④ Call Preset ⑤ PTZ Mode : The PTZ mode is toggled between Pan/Tilt and Zoom/Focus mode whenever this button is pressed. ⑥ Pan Left / Focus Near ⑦ Pan Right / Focus Far ⑧ Tilt Up / Zoom In ⑨ Tilt Down / Zoom Out [ Camera selection ] The PTZ cameras can be controlled in either full screen or split screen mode.
QNVR installation and user manual 4-2. PTZ Control by remote keyboard 1. Select Dome from the keyboard, ensure the keyboard is in Pan and Tilt mode. 2. Use the joystick to move the camera. * For more detail, please refer to your keyboard manual. 4-3. PTZ Control by remote controller [ Camera selection ] The PTZ cameras can be controlled in either full screen or split screen mode.
QNVR installation and user manual Setup Menu 1. Display 1-1. OSD Setting On Screen Display Setting: Selecting whether the various information is shown on the screen or not. Status Bar The display bar at the bottom of the screen can be set to be permanently on or to disappear after a period of time. Playback Bar The control bar in the play mode can be set to be permanently on or to disappear after a period of time.
QNVR installation and user manual Resolution The resolution of recording can be displayed or not (On/Off) Frame Rate The frame rate of image can be displayed or not (On/Off) Data Rate The data rate of image can be displayed or not (On/Off) PTZ display When in telemetry mode the on screen telemetry display can be set to be Always on or to disappear after a set period of inactivity 5 or 10 second or Off. PTZ Timeout The PTZ operation can be set to time out after a period of time.
QNVR installation and user manual 1-2. Live Setting The live settings are used to set up a sequence of either full screen camera images or multi screen displays Sequence Set Use the Up and Down arrows or the mouse roller wheel to select either: Full Screen, Quad, 9 or 16 way split sequences. The display will change to allow individual sequence times to be set per channel or split screen option. Use the select key to turn the cell green and then the Up and Down keys to change the values.
QNVR installation and user manual Cameras can be hidden from the viewer in live or play back mode. Select the camera to be made covert using the up and down keys, then press select to turn the camera green, toggle between on and off with the up and down buttons. Alternatively use the mouse to select the camera and click between on and off. In order to view covert cameras in Live or Playback, it needs to be turned off in the menus, this requires the necessary user rights. 1-4.
QNVR installation and user manual 2. IP Camera Set up, for live viewing and recording Note: Please ensure that all IP cameras are connected to the same network as your NVR and that the network settings for your QNVR are properly setup (See Network Settings). Overview: The QNVR allows great flexibility in the configuration of the recording and viewing of the attached IP cameras.
QNVR installation and user manual 2.1 Camera Discovery and Connection Note: It is best to set up the cameras stream settings prior to carrying out the Discovery and connection operation. 1. Enter the Main Menu of the QNVR, and go to: IP CAMERA > BASIC 2. Click on the Camera Discovery button 3. Click the Scan button, and wait till the NVR discovers the cameras. 4. Assign logical channel numbers to each camera, so that they appear in the correct order in the 16 way split screen layout. 5.
QNVR installation and user manual 2.2 Constant record setup 2.2.1 Camera set up for Constant record mode Use the SmartManager utility supplied with the VK2 cameras to set Stream 1 to the required Resolution, Frame rate and Bit-rate. Note, the parameters set across all camera on the system must not exceed the through put figures shown in Table 1 below: D1 QNVR max. Cameras 16 Total Recording frames 640 ips IP Cameras HD 720P Total max. Recording Cameras frames 16 320 ips HD 1080P Total max.
QNVR installation and user manual 3. Check IP Camera > Basic > Alarm 4. Set IP Camera > Basic > Schedule = Stream 1 = AL+M+N1 If Live viewing is to be done in a lower resolution, check that IP Camera > Basic > Live stream is set to Stream 3. 2.4 Stream Switching record setup 2.4.1 Camera set up for Stream Switching record mode It is necessary to configure both Streams 1 and 3 in order to be able to operate in this mode.
QNVR installation and user manual 2-5. IP CAMERA menu overview 2.5.1 Basic Channel – This is the logical number that the camera is allocated during the discovery section Status – “Connected” means the camera is enabled, “Disconnected” means the camera is disabled.
QNVR installation and user manual 2-6. Normal (Time Lapse) This configures the various recording settings per channel in the normal record modes 1 to 4. Normal (TL) 1 to 4 is set up by selecting each option via these arrows. Each channel can be individually configured for recording stream and Audio on/off. Select the stream & audio to record. Click the “Copy Camera Setting” box to copy the recording settings from one channel to other channels.
QNVR installation and user manual 2-7. Alarm This configures the various recording settings per channel in the alarm record mode. There are 16 sensor inputs on the rear of the NVR, these can be used to initiate the alarm record mode. Will need to change screen shot The stream, audio are set up in the same way as the normal recording. Preset on Alarms – Note: Only available on RS485 Telemetry You can enable PTZ cameras to move to a preset position when a sensor alarm occurs.
QNVR installation and user manual 2-8. Motion Motion on any channel can trigger recording of that camera. This configures the various recording settings per channel in the motion record mode. The stream, audio are set up in the same way as the normal and alarm recording mode. Sensitivity The sensitivity of motion detection, there are 10 levels ranging from 1(low) to 10(highest). It is recommended that each level is tested to find out which one suits that particular camera site.
QNVR installation and user manual Check the area number to store the motion detection area, click “Accept and Exit”. You can set the motion detection area up to 8. 38 QNVR Installation Manual V1.
QNVR installation and user manual 2-9. Schedule The Schedule mode allows the operator to tailor the recording characteristics of the QNVR to each individual hour of the week. As default the Schedule is set to record in Profile 1 (Al+N1 : Alarm + Normal Time Lapse mode 1) To program the schedule to each sites individual requirements, use either keys on the front panel or more easily via the mouse.
QNVR installation and user manual The record mode at the top of the list is the one that takes priority. In the example above Alarms will take priority to over all else. So when an alarm input is triggered the record setting for that input will be used. If there are no active alarm inputs, then the NVR is looking for cameras with motion in the scene, when motion is detected then the Motion Record settings will be used.
QNVR installation and user manual 3. System 3-1. Basic User can set Language, Auto Delete Mode, Date Format, Time/DST Set and VGA resolution. Also Initialisation and system Information is available. Language The default is English. Italian, French, Hungarian, Slovak, German, Russian, Chinese, Dutch, Spanish, Portuguese, Japanese, Danish and Polish are available. HDD Overwrite Generally this should be set to on to ensure that the NVR does not stop recording when the hard drives are full.
QNVR installation and user manual If the country does not appear in the list, use the User define option. Note : Playback following time change The NVR uses the time and date to index video on the hard disk drive so you can find it later. Changing the time can cause the NVR to work improperly, when you try to play back video. If you set the hour ahead, this is not a problem. But, if you set the hour back, there will be more than one recording with the same time stamp.
QNVR installation and user manual 3-2. Disk Format Formatting of the drive is used when new drives are installed or you need to wipe all information on the disk. Click on OFF to turn to ON, then click on Execute, click YES, to confirm E-SATA Function This allows the E-SATA port on the rear panel to work as the port for storage(Internal HDD) or backup(Manual Archive). Smart This function is used to keep a check on the health of the Hard disk.
QNVR installation and user manual 3-3. Account The NVR can have the following different levels of operators, each with different users rights and passwords: Admin level : Operators logged in at this level has full rights Manager level : Operators logged in that this level as default have access to all except: Stopping Recording and Shutting down the NVR. Users 1-25 : Operators logged in at this level only have the ability to search and play, control PTZ cameras and get access via the network.
QNVR installation and user manual Automatic timed log out The system can be set to automatically log out a user after a certain amount of time if no key presses have been made. The operator level has to have been activated before this can be set. Click on the boxes adjacent to “Local” for the time out period for operation from the front panel. Click on the box adjacent to “Client” for the time out period for operation from the client software. This can be set to either: Off, 15 mins, 30 mins or 1 Hour.
QNVR installation and user manual 3-5. PTZ Setup The NVR can control PTZ cameras via network or a RS485 connection on the rear of the NVR. The cameras can have individually selectable protocols with a choice of Vista PD, Pelco P or Pelco D. The Baud rate can also be selected. PTZ Controller The NVR needs to be setup to accept the VKBD3im or VKBD4 keyboard, as a default this will be set to the correct protocol and baud rate. The NVR address – This sets the RS485 Address of the NVR.
QNVR installation and user manual 4. Network If the NVR is connected to a network, this icon ( ) will be shown in the OSD display. This menu can only be accessed if the user has the necessary rights. (Default password is 00000000). With in the Network menu the DDNS (Dynamic Domain Named Server), IP addresses, NTP and Live can be set. 4-1.
QNVR installation and user manual Bandwidth It is possible to set maximum limits for the bandwidth utilisation on the network port of the unit. Main Port It allows the selected network port to work as the port for NTP, e-mail. 4-2. NTP The Network Time Protocol Setting allows the NVR time to be synchronised with an external time server. The default is NTP OFF. When turned on the Type of service can be selected, options are Default (time.bora.net), Domain and IP.
QNVR installation and user manual 5. Event This section is used to inform the user as to an event occurring, this can be by the sounding of a buzzer or by sending an E-mail to a predefined address. 5-1. E-Mail Registration Within this section up to 6 users can be set-up to receive an email on the occurrence of an event such as Video Loss / Alarm / Motion or Power Loss. An E-mail will only be sent if the DVR is sitting on a network with access to the Internet, e.g. through a router.
QNVR installation and user manual Send Test Mail : specified range of time. Enable to send a test E-mail to the addresses so allowing the installer to verify if the setup is correct. SMTP Mode The SMTP (Simple Mail Transfer Protocol) function allows e-mails to be sent over a LAN The default is SMTP Mode “OFF”. In order to activate SMTP Mode, choose SMTP Mode either IP or Domain first. Then, put ID, Password, IP address, and port. Finally press “SMTP Status Check” to test. 5-2.
QNVR installation and user manual 5-3. Beep Out The buzzer can be set to sound on the following occurrences: Video Loss; Alarm input; Motion detection; Power Loss; Smart (Hard disk monitoring). The duration of the beep can be set. 5-4. Alarm Out The Alarm out relay can be set to activate on the following occurrences: Video Loss; Alarm input; Motion detection; Power Loss; Smart (Hard disk monitoring). The duration of the activation can be set.
QNVR installation and user manual Search Menu 1. Searching Recorded Data The user can search the recorded video on the DVR to find a specific time or event. Search To access the search option, click the SEARCH icon on the popup menu. To access the search option, press the SEARCH button on the front panel or right click the mouse and select Search, (A password may have to be entered) after which the following screen will be displayed. 1-1.
QNVR installation and user manual 1-2. Event Search This allows the user to select between ALARM, MOTION or AUDIO. Select required option by pressing the right arrow, or selecting with the mouse. ALARM – The search is for any alarm activation within the times defined. MOTION – The search is for any motion events within the times defined. AUDIO – The search is for any audio activations within the times defined. 1-3.
QNVR installation and user manual The following screen will be displayed. Hours of the day The hours which have recorded data are displayed as a coloured bar. Select the hour which you want to review, the following screen will be displayed. Minutes in the hour The minutes which have recorded data will be displayed as a coloured bar, click on the time required; the recorded data will be played back from this point. 1-4. Bookmark Search This allows the user to edit the bookmark.
QNVR installation and user manual 2. Archiving Evidence to DVD/CD or USB Once the required video has been found, it may be necessary to down load it for evidential purposes. This can be done either onto the internal CD/DVD-R writer or via the USB port on the front of the DVR. To do this press the SEARCH button and using the down button move to ARCHIVE, once highlighted press SEL, the following screen will be displayed.
QNVR installation and user manual [Adding the files to archive] Press the ADD button, the following screen will be displayed. From/ To You can set up the start and stop time which is required to be backed up to the internal CD/DVD-R or USB device. Highlight this option, then press SEL, then use the alphanumeric buttons or the mouse to set the time and date. Repeat for the end time. Channel As long as the EXCLUSIVE file format is selected, the number of channels to be down loaded can be selected.
QNVR installation and user manual 3. LOG The log file contains information on the following: All : Power, Record, Operation, Event, Archive Power : Power on, Power off, Power fail Record : Rec fail, Rec start, Rec stop, Rec error, Rec full Operation : Play start, Play stop, HDD format, Menu set Event : Alarm, Motion, Audio, Video loss, Email fail Archive : This lists the USER, time/date when Archive was done, and time range of archived section.
QNVR installation and user manual Client Viewer software Each DVR comes with license free viewer software to view the DVR across a network. To be able to do this the recommended minimum specification for the PC is as follows: Recommended PC specification CPU : Intel® Core 2 Duo, E8500 @3.16GHz RAM : DDR2, 4GB Graphic : NVidia GeForce 9500 GT, 512MB OS : Windows XP Installing software When you put Quantum Network installation CD into your PC, it will auto run and lead you through an installation wizard.
QNVR installation and user manual 2. Logging on The following window will appear. To connect to the DVR, enter the units: IP address; DVR Port (2000 ids default), ID and Password. Then, click “OK”, to start the live monitoring. Description field is the name of area / Building / location of the DVR, this should be typed in he first time the unit is connected to, this will store it in the address book. Address book Click on the Arrow to the left of the IP address, the following box will appear.
QNVR installation and user manual 3. Explanation of Screen Buttons 60 QNVR Installation Manual V1.
QNVR installation and user manual 4. Live Monitoring Split Screen options (1/4/6/7/8/9/10/13/16/30) Spilt Screens can be viewed during both live and playback. The splits screens available are: full screen,4,6,7,8,9,10,13,16 and 30 way. 1) Single Screen 2) 8 Way Split Screen 61 QNVR Installation Manual V1.
QNVR installation and user manual Full Screen on/ off When the full screen button is selected, a tool bar offering the various split screen options, and the Exit key will be displayed at the bottom of the screen. OSD on/off The OSD button will toggle between the on screen titles etc being shown or hidden (Smart) Arrange On/Off If cameras are being displayed in segments that are not logical, the Smart button will rearrange and put camera input 1 into segment 1 (Top Left) etc.
QNVR installation and user manual Image Save / Load Still images being displayed at any point on the live or playback screens can be saved to a file on the PC, to save images click on the save button: A box will appear allowing the naming of the files, if a multiscreen image is showing on screen then a still image from each of the displayed channels will be saved in either JPEG, BMP or TIF format The still image is stored as default in C:\ HNClient: Saved folder, as a Jpeg image using the date and time
QNVR installation and user manual Playback (Step Backward, Backward, Playback, Pause, Recording, Stop, Step Forward) Audio (Mute, Volume, Select Audio, Microphone) Select Audio: Toggles through audio channels. 64 QNVR Installation Manual V1.
QNVR installation and user manual 5. Remote Search Search(Date/Time/Event/Calendar), Archive(Remote Archive), Log(Remote Log) are available. 5-1. Search This Remote Search is able to play back video on the PC direct from the hard disk storage on the DVR. There are 3 options for as follows. 1) Date/Time 2) Event 3) Calendar Date/Time Search When the cursor is placed over a part of the time and date a drop down arrow will appear, use this to set the required value. When set.
QNVR installation and user manual A list of the available events will appear. To play an Event select it and click Play. To stop playing back press Stop the search screen will appear to allow another search to be carried out, if not required, click cancel followed by live. Calendar Search Select the date required (as long as the date is highlighted in Blue there is recorded data on from that day). There are 3 options for selecting the required time once the date has been selected.
QNVR installation and user manual Hours of the day Minutes in the hour [ Select Channel ] Channels can be included or excluded dependent on query. This is available within Search, Backup and Logs. 5-2. Archive Remote Archive – Date/Time Enter the Start and End dates and times, by hovering over the selections, a drop down box will appear. Once selection is made, then “click” calculate, the file size will be displayed. Finally click “Archive”, the file will be transferred to C:\ HNClient \Download.
QNVR installation and user manual Select either: Alarm, Motion or Audio from the top of the screen. A list of events will appear. Click on the event required, it will be come highlighted. Click on Calculate, the file size will be calculated, this may take a few seconds. Finally click Archive; the file will be transferred to C:\ HNClient \Download.
QNVR installation and user manual Click on Calculate, the file size will be calculated, this may take a few seconds. Finally click Archive; the file will be transferred to C:\ QNVR \Download. [ Play back down loaded files ] Open the viewer software but do not connect to a unit, click the cancel button to remove the log on box. Next click on the Local search button ( ) the normal search box will appear, use the same method to search the files on the PC and Play back 5-3.
QNVR installation and user manual System Information The system info displays the Mac address and software version information. Status Information This shows the status of both the Hard disk and the recording modes of each channel. 70 QNVR Installation Manual V1.
QNVR installation and user manual 6. Remote Setup (Menu settings - same as DVR) 6-1. Display This is the same as the Display Menu of NVR, refer to setting the Display Menu of NVR. OSD setting The Symbols and text displayed on screen can be controlled: 1. The status bar can be set to be off/ Always on or be on for 5 or 10 seconds after a key press. 2. The Event symbols such as Motion, Audio, Pan / Tilt can be displayed or turned off. 3. The camera name can be displayed or turned off. 4.
QNVR installation and user manual Camera Covert Cameras can be remotely set into Covert Mode, they are still being recorded but cannot be viewed local to the system, or by any remote user apart from the Administrator on line. Camera Name Up to 32 Characters are available for each camera name. 72 QNVR Installation Manual V1.
QNVR installation and user manual 7-2. IP Camera This is the same as the setting of IP Camera Menu of NVR. Basic This configures IP cameras. It allows you to set the IP address and parameters of IP cameras, like stream, resolution, frame rate. Normal(Time Lapse) This configures the various recording settings per channel in the normal record mode. Each channel can be individually configured for recording stream and Audio on/off.
QNVR installation and user manual Motion Motion on any channel can trigger recording of that camera. This configures the various recording settings per channel in the motion record mode. The stream, audio are set up in the same way as the normal and alarm recording mode. Setting the motion detection area The motion detection area allows you to mask out areas where you would like motion to be detected in. You can left click mouse, hold and drag it to mask the motion detection area.
QNVR installation and user manual 7-3. System Basic This section is used to select: Language Date format DST Setup IR Remote Address VGA Resolution HDMI Resolution Bandwidth Disc Format Formatting of the drive is used when new drives are installed or you need to wipe all information on the disk. E-SATA Function This allows the E-SATA port on the rear panel to work as the port for storage or backup. Smart This function is used to keep a check on the health of the Hard disk.
QNVR installation and user manual PTZ Setup for camera [ ID ] Each camera input can be allocated an RS485 ID between 1 and 255. [ Protocol ] Each camera output can have individual protocol associated with it. an [ Baud rate ] The Baud rate of each PTZ camera can be set the choices are: 2400bps/4800bps/9600bps/19200bps NTP Setup NTP setup allows the NVR to have its internal clock synchronised with an External clock.
QNVR installation and user manual 7-4. Event Email Registration The NVR will send E-mails to up to 6 defined addresses under certain conditions such as Alarms or video loss. The screen is where you setup the receiving address and address that the DVR will send from. The mails can be set to be sent immediately an event occurs, Daily or Weekly. Email Out The actions which cause an e-mail response can be defined within this screen.
QNVR installation and user manual Alarm Out The Alarm output relay can be set to activate on the following occurrences: - Video Loss - Alarm activation - Motion Detection - Power loss The duration of the relay closure can be set. 78 QNVR Installation Manual V1.
QNVR installation and user manual 8. Local Search (viewing downloaded footage) This allows playback of video which has been downloaded top the PC. 8-1. Search Searches can be done by Date/Time, Even and Calendar. Date/Time Search Hovering over the Date and Time bars will allow drop down boxes to select the required time and Date. Once set, click Play. Event Search Choose the Event search box then choose the type of Event you are searching for, options are: Alarms, Motion or Audio.
QNVR installation and user manual Calendar Search When the Calendar option is chosen this screen will appear, any day with recording available will be highlighted in Blue. Select the required day. Any downloaded event s will be shown, click on the event, the red line will move to that event. Then click Play to review the recording. Bookmark Search The files with a bookmark will be shown, select one of them. Then click Play to review the recording. 80 QNVR Installation Manual V1.
QNVR installation and user manual File List Search The archive list will be shown in order of file name, select the file you wish to review. Then click Play button. 8-2. Log Clicking on Log will display the log file from the unit. This file can be printed, by clicking Print. 8-3. Info Click on Info. This will display the version of the software client being used. 81 QNVR Installation Manual V1.
QNVR installation and user manual 9. Local Setup This allows the setup of the viewing of the software on the PC. 9-1. Global This screen allows the following: Draw mode to be set to YUV or RGB Date Format to be set to: DD/MM/YYY, MM/DD/YYYY or YYYY/MM/DD. Save Format, for the saving of stills as either JPEG, Bit Map or TIF. Location for where stills are saved. 9-2. Opacity The opacity or “boldness” of the OSD can be individually set per function. The lower the number the more see through the box.
QNVR installation and user manual 9-3. Audio Buffer Audio Buffer settings are there to adjust the audio over the network, this will compensate for different network speeds ( LANs, WANs etc). This can only be adjusted if the LIVE video is switched off. Adjust each variable to achieve best quality video for Network bandwidth available, this is best done through trial and error. 9-4. Camera Name Each camera can be titled, each title can have up to 32 characters. 9-5.
QNVR installation and user manual 10. Telemetry Control (Pan/Tilt/Zoom/Focus) When PTZ button is being pressed, PTZ control icon will be pop-up on the live image. 10-1. Pan / Tilt / Zoom / Focus When PAN/TILT button is clicked the Pan/Tilt control appears, this allows Left, Right, Up and Down Control of PTZ cameras When Zoom/Focus button is clicked, the control changes to Zoom in on the up arrow, Zoom out on the down arrow. Focus near on the left button and focus far on the right arrow.
QNVR installation and user manual 10-2. Preset / Learn Preset & Learn icon The presets button can be activated by clicking on the centre of the control icon, the preset symbol will appear and the Preset selection box will appear. To save a preset, move the camera to the desired position then click “Set” followed by the desired number. To recall the preset, click “Call” followed by the desired number. 85 QNVR Installation Manual V1.
QNVR installation and user manual 11. Screen Position Save/Load 11-1. Screen Position Save The positions of each channel on screen are saved into the registry and then restored the next time you open the client viewer software. 11-2. Screen Position Load It is possible to edit & restore the screen position which is stored in the registry. Select one of the screen positions, then click OK button. 86 QNVR Installation Manual V1.
QNVR installation and user manual 12. Firmware Upgrade User can select Firmware Upgrade menu, if a new version of firmaware exits in the C:/HNClient/Upgrade folder ,then the message ‘New program found!’ will be displayed if there is no file then ‘New program not found!’ message will be displayed. To proceed with upgrading press the OK button and select each firmware files to upgrade it to the system, by ticking the boxes. Once the upgrade has been completed the following message will appear.
QNVR installation and user manual Appendix 1 Dynamic IP (Supporting DDNS Server) With DDNS Server, This allows a user to connect to the unit remotely without the need for a fixed IP address. (Please register your ID & Domain at www.ddns-dvr.com in which you can use their DDNS server as free of charge) 1. Visit www.ddns-dvr.com to get the DDNS user ID & PW as well as Host name. 2. Click to create / set account of “Dynamic DNS”. 3. Select “Create Account” menu. 88 QNVR Installation Manual V1.
QNVR installation and user manual 4. Create Account. Fill in all blanks in order to create new account. ID & Password will be emailed to you when the account is setup correctly. Once the DDns-Dvr account has been setup, it is necessary to add the details in the Network menu of DVR. Set up DDNS 1. Change DDNS to ON 2. Input User ID 3. Input User PW 4. Input Domain 5. Click “DDNS Status Check”. If it is “ok”, click “Apply”. NOTE : In DDNS Setup, The Domain Name has to be filled in.
QNVR installation and user manual Appendix 2 Setup for DVR port & web server port using IP sharing router (Port Forwarding) 1. To use IP sharing router, “Dynamic IP” should be set to “OFF”. ① DVR Port : This can be set to any number between 2000 to 65535. ② Web Server Port : This can be set to any number between 2000~65535, as long as it is not the same as the DVR Port number. 2. Setup “virtual server” on IP sharing Router It is for setting virtual server to forward IP which is allotted to DVR.
QNVR installation and user manual Appendix 3 Specification Model Camera Input Output Input via Audio network/Output Sensor In / Alarm Out Operating System HDMI Resolution VGA Resolution Display Split Display Compression Resolution (Pixel) Recording Mode Rec Frame Split Display Search Mode Playback Mode QNVR Max 16ch 1 HDMI , 1 VGA Video Network Archive Network Interface Protocol Serial Communication Web Browser Event Transport Viewing / User Access Interface Archive Device Motion Detection Event Even
