User Manual
a-3D
The Q-3D is a portable high precísíon GimbaJ assembly specifical1y designed for lhe FPV+,
Turnigy ActlonCam and GoPro Hero 3 series camera systems. The Gimbal system is
manufactured trom high grade aJumlnlum aJ/oy and incorporates a brushless motor drive
system and an extremely aeeurate and intel1ige"t eleetronic control system. The Q-3D
Gimbal assembly can be used for appllcations such as aerial videography and photography
etc. The highly precise and stable structure of the gimbat assembly
\Viii
ensure ttiat your
eamera system remains stabte in fli!;lht for lhe besl possibt loolage.
FixellSCrew(M3x12)-----l
ofGimbal
(J)GYro
,......:~.!>+------Horizonlal molar
+---
Rolling molar
"'-+---Till motor
• Supports FPV+,Turnigy AclionCam and GoPro Hero 3 séries camera video auxiliary (
• Supports power supply voltage compensalion.
• snort circuit proteclion.
• Supports ínítial lill and custom roll angte.
• Supports stick position and rate mode.
• Supports regular receivers.
~
..
• Operatíng voltage: DC 7.4V-28V (recommended 12V, 3S UPoly battery).
• Operating curren!: 500mA-600mA (subject 10 voltage supply and motor power).
• Operating temperature: _15° -65°c.
• Sensor: 3-axis MEMS gyro and 3-axis MEMS aceeleóomeler.
• Conlrol accuracy °0.02°.
• Angle eontrol range: -135° - 90° (Iilt) -45° - 45° (rall).
• Compatíble camera systems: FPV+, Tumigy ActionCam, GoPro Hero 3 Series.
• Size: 114.3mm x 97.5mm x 106.6mm (L x W x H).
• Weigh!: 188g (without eamera).
• To ensure correct operation the camera system rnust
be fitted and seeured 10 lhe gimbal prior to power up
and calibralion.
Till molor
Balance
(8
• If lhe eenler of lhe gimbal and camera syslem is
unbalanced, re-assemble lhe syslem wilh lhe balance
aeeessory as necessary.
---_._-~---~~-~--------_....!-_---~-------------
-1 -
~,. u __ ••_ •.••_._u ••.__ ~~ •.r ••~~~~-~._~ ••
->.:-""-; ,~ .~ - , ~-::"'~ -
~,:e"':/' _ ~~..
:':7.:. ,-
3.0 lnetellation instructions . '.. " -
""$ :- ••.. _ . ' •..•~
-~--4
DJI
Phanlom
.•.
Quanum Nova
3.2 Align lhe Gimbal rail \ .
lhe fixing block ano slide
lhe gimbal onto lhe b0iID07
01
lhe fixing block in lhe
direction shown.
lhe spring onto a
2.SJ:<eW,Ihen align
:à:;
&:reW
wilh lhe Ihreaded
anel
1ighlen 10fix lhe
,2-
3.1 Use 2 x M3x8 screws 10
installlhe Gimba\ fixing
block onto lhe bottom of
lhe fuselage .
3.4 Utilising lhe camera fixing
frame, fillhe camera 10 lhe
Gímbal syslem, and secure
by using 2 x M2x4 screws.
a-3D
c ~
<E:g
®
_..
_..
_G FIt
n r.~
:1
@~
L®L--14-
---1-1--@
A. Connecl aírcraft power
a.
Connecl camera controller
C1.Connecl receíver's tiltlroll
channel, centrol lhe tílUroll of
lhe gimbal
C2. Connecl usa adapter,
upgrade gímbal control
systern,
-3'