User`s manual

ManualsBrandsQuatech ManualsNetwork RouterAirborneDirect ABDG-ET Series

Quick Start Guide

AirborneDirect™ Ethernet Client Adapter

ABDG-BR-DP501/IN5010

Revision v1.0

May 2011

Document Number: 100-8108-100

Kit Contents:

Upon receiving the kit please check that you received the following:

 ABDG-BR-DP501 or ABDG-BR-DP5010 Unit

 5VDC Power Supply (2.1mm barrel jack)

o included with ABDG-BR-DP501

o optional for ABDG-BR-IN5010, included only if ordered as an accessory

 2dBi, 2.4Ghz 50 ohm, omni-directional antenna

 Quick Start Guide

 AirborneDirect™ software and documentation CD

If any of the above contents are missing or appear damaged please contact Quatech Sales support directly at (800) 553-1170 or

support@quatech.com.

What you will need:

To evaluate the unit you will need the following components and facilities:

 ABDG-BR-DP501 or ABDG-BR-IN5010 unit with included antenna attached.

 Laptop or desktop system with an Ethernet port.

 Power outlet for ABDG-BR-DP501/IN5010 power supply. Optionally 5-36 VDC power for the terminal block attachment (IN5010).

 802.11b/g network for testing the unit, either AdHoc or Infrastructure (Access Points) mode. The test network configuration must be

known. Required information will include:

o SSID (Wireless network name).

o Security settings (WEP, WPA, WPA2, etc.).

o Security credentials (passphrase, key or certificates).

o Static IP address, Subnet Mask and Gateway address if static IP addresses are used on the test network.

 A web browser on the laptop top or desktop (Internet Explorer, Firefox, Opera and Chrome v4.0 are supported).

Summary of content (13 pages)

PAGE 1
Quick Start Guide AirborneDirect™ Ethernet Client Adapter ABDG-BR-DP501/IN5010 Revision v1.0 May 2011 Document Number: 100-8108-100 Kit Contents: Upon receiving the kit please check that you received the following:      ABDG-BR-DP501 or ABDG-BR-DP5010 Unit 5VDC Power Supply (2.1mm barrel jack) o included with ABDG-BR-DP501 o optional for ABDG-BR-IN5010, included only if ordered as an accessory 2dBi, 2.
PAGE 2
AirborneDirect™ Ethernet Client Bridge Quick Start Guide Quatech, Inc. Getting Started when no open Network available: 1 Open the AirborneDirect™ packaging and locate the Install CD. 2 Place the CD in the CD/DVD drive of the laptop or desktop you will be using to configure the AirborneDirect™ device. Follow the on screen directions for installation of the appropriate device software and documentation. 3 4 Connect the Ethernet cable on ABDG to an Ethernet port on the laptop or desktop system.
PAGE 3
AirborneDirect™ Ethernet Client Bridge Quick Start Guide Quatech, Inc. Right Click the Unmanaged Device then: 1. Select Change Management State 2. Select Manage OEM-Cfg1 3. Select Device OEM-Cfg1 is Factory Default 8 The device’s status will move to managed and the device will be displayed under the device type/group it belongs to. Right click the device and then: 1. Select Connectivity Tools 2. Select Launch Web Browser for OEM-Cfg1 9 Opening web page shows adapter status.
PAGE 4
AirborneDirect™ Ethernet Client Bridge Quick Start Guide Quatech, Inc. Getting started with an open Network available: 1 Open the AirborneDirect™ packaging and locate the Install CD. 2 Place the CD in the CD/DVD drive of the laptop or desktop you will be using to configure the AirborneDirect™ device. Follow the on screen directions for installation of the appropriate device software and documentation. 3 4 Connect the Ethernet cable on ABDG to an Ethernet port on the laptop or desktop system.
PAGE 5
AirborneDirect™ Ethernet Client Bridge Quick Start Guide Quatech, Inc. When configured correctly the LED pattern should match the following: 11 12 100-8108-100 ABDG-BR-DP5XX POWER: LINK : COMM:  Green  Green  Red ABDG-BR-IN5XXX COMM: LINK : POST: POWER: No TCP Connection  Off  Green  Green  Blue TCP Connection  Green  Green  Green  Blue To use the adapter on the wireless network, address all traffic to the IP address of the Ethernet Client’s Ethernet port.
PAGE 6
AirborneDirect™ Ethernet Client Bridge Quick Start Guide Quatech, Inc. Getting started with no open Network available (No AMC): 1 Open the AirborneDirect™ packaging and locate the Install CD. 2 Place the CD in the CD/DVD drive of the laptop or desktop you will be using to configure the AirborneDirect™ device. Follow the on screen directions for installation of the appropriate device software and documentation. 3 Connect the Ethernet cable on ABDG to an Ethernet port on the laptop or desktop system.
PAGE 7
AirborneDirect™ Ethernet Client Bridge Quick Start Guide Quatech, Inc. When configured correctly the LED pattern should match the following: 11 12 100-8108-100 ABDG-BR-DP5XX POWER: LINK : COMM:  Green  Green  Red ABDG-BR-IN5XXX COMM: LINK : POST: POWER: No TCP Connection  Off  Green  Green  Blue TCP Connection  Green  Green  Green  Blue To use the adapter on the wireless network, address all traffic to the IP address of the Ethernet Client’s Ethernet port.
PAGE 8
AirborneDirect™ Ethernet Client Bridge Quick Start Guide Quatech, Inc. Express Setup Configuration Page When the devices web interface is accessed for the first time an Express Setup page will be shown. This page is designed to allow a quick device set-up by presenting the most popular device configuration options in a single location. For more advanced configurations the full set of options are available in the feature links (left-hand column).
PAGE 9
AirborneDirect™ Ethernet Client Bridge Quick Start Guide 100-8108-100 Quatech, Inc. Step Description Select Wireless LAN Connection Type If you are using Access Points make sure this is set to Infrastructure from the drop down menu. If you want to use AdHoc set this accordingly. Additional settings may be required to fully configure for AdHoc mode. Select SSID Enter the name of the wireless network you wish to access. This field is case sensitive.
PAGE 10
AirborneDirect™ Ethernet Client Bridge Quick Start Guide Quatech, Inc. Step Description Select Telnet Port This is the port used to access the Airborne device for configuration, using a TCP/IP connection. If the Ethernet Client uses port 23 this must be changed to an alternate port number e.g. 8028. Default Port: 23 Select Internal FTP Server Listen Port This is the port on which the Airborne device’s FTP server is listening.
PAGE 11
AirborneDirect™ Ethernet Client Bridge Quick Start Guide Quatech, Inc. Table 2 – IN5010 Indicator LED’s LED Color POWER Adapter is not powered.  POST Airborne Device State Adapter is powered. Adapter is not powered. Adapter failed Power On Self Test (POST) and is not configured for wireless communication. Adapter passed POST but is not configured for wireless network communication. Adapter passed post and is configured for wireless communication. LINK Adapter is not powered.
PAGE 12
AirborneDirect™ Ethernet Client Bridge Quick Start Guide Quatech, Inc. Table 3 – DP500 Indicator LED’s LED POWER Color Airborne Device State Adapter is not powered. Adapter failed Power On Self Test (POST) and is not configured for wireless communication. Adapter passed POST but is not configured for wireless network communication. Adapter passed post and is configured for wireless communication. LINK Adapter is not powered.