EA00022 User Manual EA00022 User Manual Telematics Device EA00022 QSZTRACEA00022UM0101 Version: 1.
EA00022 User Manual Document Title EA00022 User Manual Version 1.01 Date 2021-09-07 Status Released Document Control ID QSZTRACEA00022UM0101 General Notes Vehicle Control Module EA00022 integrates the components and functions such as OLED display, headlight control, Powertrain Control Module(PCM), Battery Module, brake actuator, throttle actuator, and speaker while providing communication with integrated bluetooth and GPS positioning modules.
EA00022 User Manual Contents 0. Revision History............................................................................................................................... 1 1. Introduction.....................................................................................................................................2 1.1. EA00022 Series Products......................................................................................................2 1.2. Reference.....................................
0. Revision History Version Date Author Description of change 1.
1. Introduction The Vehicle Control Module EA00022 integrates the components and functions such as OLED display, headlight control, Powertrain Control Module (PCM), Battery Module, brake actuator, throttle actuator, and speaker while providing communication with integrated Bluetooth and GPS positioning modules.
2. Product Overview 2.1. Product Appearance Figure 1. EA00022 Appearance 2.2. Parts List Table 4. EA00022 Series Parts List Name Picture Description tracker EA00022 125.5mm*62.08mm*101.0mm 3. Interface Definition The EA00022 harness have 24-pin interface connector. It contains the connections for power, Speaker, headlight and so on.
Figure 2. 24-pin Connector of the EA00022 Table 5.
4. Device Cable Color Table 6.
5. Started 5.1. Opening and Closing the Casing To open/close: Loosen or fasten the screws to open or to close. 5.2. Installing a SIM Card Install the SIM card into the holder when power is off as shown blow. Take care to align the cut mark, and then close the case.
5.3. Power Supply Connection The red wire is power line ,the black wire is ground line and blue wire is power EAN line . The input voltage range for this device is from 12V to 60V DC. Figure 5. Example of Connection for power 5.4. CAN Connection The yellow wire is CAN_H line, the green wire is CAN_L line. Need connect CAN-Bus tools for communication. Figure 6. Example of Connection for CAN 5.5.
5.6. Throttle The blue wire is throttle weak up 2 line, the black wire is ground line, the red wire is power line, the yellow wire is throttle weak up 1 line. Figure 8. Example Connection to Throttle 5.7. Brake Right The black wire is ground line, the red wire is power line, the orange wire is weak up line. Figure 9. Example connection to brake right 5.8. Brake Left The black wire is ground line, the red wire is power line, the green wire is weak up line.
Figure 10. Example connection to brake left 5.9. Headlight The white wire is ground line, the green wire is power line. Figure 11. Example connection to headlight 5.10. Speaker The white wire is ground line, the green wire is power line. Figure 12.
6. Basic communication EA00022 Can communicate with the backend server through LTE Cat-M network, and transfer reports of emergency, Geo-fencing, device status and schedule GPS position ect…service provider is easy to setup their tracking platform based on the functional wireless. 7. BLE 7.1. BLE working mode explanation EA00022 is installed in the shared scooter and supplied by the main battery of scooter. With the external power(main battery of scooter) supplying , the BLE of EA00022 works.
10. FCC Certification Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.
ISED RSS Warning/ISED RF Exposure Statement ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence.
