GSM/GPRS/GPS Tracker GL200 User Manual TRACGL200UM001 Revision: 1.04 http://www.queclink.com sales@queclink.
GL200 User Manual Document Title GL200 User manual Version 1.04 Date 2012-03-21 Status Release Document Control ID TRACGL200UM001 General Notes Queclink offers this information as a service to its customers, to support application and engineering efforts that use the products designed by Queclink. The information provided is based upon requirements specifically provided to Queclink by the customers.
GL200 User Manual Contents Contents ............................................................................................................................................2 0. Revision history ............................................................................................................................3 1. Introduction...................................................................................................................................4 2. Product Overview ...................
GL200 User Manual 0. Revision history Revision Date Author Description of change 1.01 2010-09-19 Ella HUANG Initial 1.02 2010-12-20 Ella HUANG 1. Modify interface define and pictures in chapter 2.4,2.6,3.3; 1.03 2011-04-11 Ken JI 1.Add Ignition Detection connection position in chapter 2.5 2.Add the input function description in chapter 2.6 3.Add the output function description in chapter 2.7 4.Modify the external cable interface description in chapter 3.3 1.
GL200 User Manual 1. Introduction GL200 is a powerful GPS locator which is designed for vehicle, pets and assets tracking. With superior receiving sensitivity, fast TTFF and GSM frequencies 850/900/1800/1900. Its location can be real time or schedule tracked by backend server or specified terminals.
GL200 User Manual 2. Product Overview 2.1. Appearance k n i l l c a i e t u n Q ide f n o C 2.2. Buttons/Mini USB Interface Description Button /Mini USB Interface Description Power Key Turn on GL200 Turn off GL200 when without charging. (If power key is enabled) Function Key Geo-Fence mode Long press the key to enable/disable Geo-Fence ID0 Geo-Fence in current position mode Long press the key to enable/disable Geo-Fence ID0.
GL200 User Manual 2.3. LEDs Description There are three LED in GL200, the description as following. LED GSM LED Event Searching network State Fast flash Network has been registered Power off SIM-PIN Locked Receives a valid protocol command is 2 GPS has fixed Slow flash Dark Solid Turn on for 3 seconds Dark Solid GPS is in fixing Fast flash GPS is on and GPS data wrong Slow flash GPS is off Dark If is 0, 150 seconds later after powers on.
GL200 User Manual k n i l l c a i e t u n Q ide f n o C 2.4.2. External Battery Interface The Pin 8 on Mini-USB connector is for external battery and named as EXTBAT pin, It can be connected to 3.7V Li-ion or Li-Polymer battery to power GL200. 2.5. Ignition Detection The Pin 7 on Mini-USB connector is for ignition detection when GL200 is used in vehicle tracking application, It is named as IGN_IND pin.
GL200 User Manual k n i l l c a i e t u n Q ide f n o C Another easy way is to connect PIN7 to a power output in the fuse box of the vehicle which is only enabled after the vehicle is ignition on. For example: the power output for radio FM. 2.6.
GL200 User Manual k n i l l c a i e t u n Q ide f n o C Example of NSW pin connect to a panic button 2.7. External Output Interface The older hardware version of the GL200 whose IMEI code is between 35946403600001X(ignore the last one parity bit X) and 35946403607338X do not support the output function ,before using the output function ,you should check if the GL200 is a newer hardware version. The Pin 9 on Mini-USB connector is a negative trigger output in newer hardware version, It is named as OUT pin.
GL200 User Manual k n i l l c a i e t u n Q ide f n o C Example of OUT pin drive a LED Example of OUT pin drive a relay If the digital output is used to drive a relay, a catch diode is showed across the relay coil, this is necessary to prevent damage to the digital output when the relay is turned off. Many modern relays come with this diode pre-installed internal to the relay itself. If the relay has this diode, insure the proper relay polarity connected is used.
GL200 User Manual 2.8. External GPS antenna specification There is a MMCX RF connector on GL200 and it is for external GPS antenna. The specification of the external GPS antenna is listed in following table. GPS antenna: Frequency: 1575.42MHz Bandwidth: >5MHz Beamwidth: >120 deg Supply voltage: 3.3V Polarization: RHCP or Linear Gain: Passive: 0dBi minimum Active: 15dB k n i l l c a i e t u n Q ide f n o C Impedance: 50Ω VSWR: ﹤2 Noise figure: <3 Connector MMCX 3. Getting Started 3.1.
GL200 User Manual Car Cigarette Charger (Optional accessory) It is used to power the GL200 with the cigarette power output on the vehicle. Car Kit Charger (Optional accessory) It is used to power the GL200 with the battery output on the vehicle. External Battery Kit (Optional accessory) It is a set of accessories include an external battery, a power control unit and a pelican waterproof casing.
GL200 User Manual 3.2. Battery Charging Please connect AC-DC power adapter with GL200. Insert the AC-DC power adapter into the power socket. During charging, the PWR LED is flashing fast. When the battery is full charged, the PWR LED will be Ever-light. You can also charge the battery by USB cable which connects GL200 with the PC. Charging time is about 5 hours. Note: Before the first time using GL200, please full charge the battery.
GL200 User Manual 3.3. GL200 External Cable Interface GL200 External Cable is a cable with a Mini USB connector and six wires which include the external power interface, ignition detect and input/output interface for GL200. Please find the detail description in following table. Color RED Black Blue White Green Yellow k n i l l c a i e t u n Q ide f n o C Name Remark External DC IN (5V) Please refer to 2.4.1 for detail Ground Please refer to 2.4.1 for detail External Battery IN (DC 3.4V to 4.
GL200 User Manual 3.4. Install SIM Card First, open the cover of SIM card.. Then insert the SIM card into the slot of SIM card according to the direction shown. Finally, cover the slot. k n i l l c a i e t u n Q ide f n o C 3.5. Install Device Into The Holder Please install the GL200 into the holder follow the following process. 3.6. Turn on/Turn off Turn on: Method 1: Press the Power key at least 3 seconds and release it to turn on GL200. At the same time, PWR LED will light on.
GL200 User Manual 4. Troubleshooting and Safety info 4.1. Troubleshooting Trouble Possible Reason Solution After GL200 is turned on, the GSM LED flashes quickly always. The SIM card is not inserted. Please insert the SIM card into GL200. k n i l l c a i e t u n Q ide f n o C Messages can’t be reported to the backend server by GPRS. Unable to power off GL200. No response from UART when configure GL200 through UART The signal is too weak; GL200 can’t register to the network.
GL200 User Manual 4.2. Safety info Please do not disassemble the device by yourself. Please do not put the device on the overheating or too humid place, avoid exposure to direct sunlight. Too high temperature will damage the device or even cause the battery explosion. Please do not use GL200 on the airplane or near medical equipment.