CM1X SERIES Installation Manual
TABLE OF CONTENTS PREFACE.............................................................................................................. 2 INTRODUCTION................................................................................................... 4 SPECIFICATIONS.................................................................................................. 8 INSTALLATION.................................................................................................... 10 BATTERY PACK WARNINGS.......
PREFACE PREFACE Thank you for purchasing this Tierra product. The materials available in this Manual (the “Manual”) have been prepared by Tierra S.p.A. (“Tierra”) for customers of Tierra products, and are designed to assist customers with the use of the receiver and its use is subject to these terms and conditions (the “Terms and Conditions”). NOTICE - Please read these Terms and Conditions carefully.
INTRODUCTION INTRODUCTION CM1X Series is Tierra’s third generation of devices and the result of our long-standing expertise in providing advanced telematics and bringing meaningful improvements in our HW to keep on meeting our customers’ necessities. Two versions of CM1X have been designed to suit the market requirements.
INTRODUCTION CM1XLED DISPLAY PANEL INTRODUCTION CM1X MAIN ENVELOPE DIMENSIONS Power LED (Red): • OFF - No power supply. • Double blink - powered and working. • Rapid blinking - key off. 122.65±0.5 102±0.5 GPS LED (green): • Off: GPS initialization phase or device in standby/wake mode. • Blinking: Searching for GPS signal. • On solid: GPS fix completed. 50±0.5 MODEM LED (green): • Off: Modem initialization phase. No network coverage or device in standby/wake mode.
SPECIFICATIONS SPECIFICATIONS CM100 Wakeup sources SIM WiFi/BLE Memory RAM Flash NAND LED Ports & Connectors Serial Port[1] CAN Bus Connector Cellular technologies multi-mode modem RF Output power Bluetooth E-GSM 900 Antennas (Internal) GNSS Receiver Frequency Motion Sensor Input/Output Input Device Output Devices Power Supply Input Battery Batteries Remote Capabilities Configuration Firmware Update[2] Environmental[3] Water/Dust Resistance Operating Temperature Range[4] Humidity Physical Dimensions Weigh
INSTALLATION INSTALLATION The following section describes the installation steps for CM1X devices. Vehicle cables and screws are not included 5. Connect the vehicle cables to the device through the connectors. Ensure that the battery line is protected by a 5A automotive fuse. CM1X DEVICES INSTALLATION 1. Disconnect the vehicle battery main switch, and maintain it disconnected for the duration of the device installation process. 2. Install the device using bolts on dedicated mounting holes. 3.
INSTALLATION INSTALLATION 6. Connect the antenna cables (CM110 only). NOTICE - If the device is not properly installed, any motion detected by the internal accelerometer will have a negative impact. False readings will occur unless the device is firmly in place. WARNING - DO NOT ALLOW the CM1X or the components of the telematic system to BLOCK or LIMIT your view outside the cab. Use goggles when drilling, cutting, or grinding on the machine.
INSTALLATION INSTALLATION CONNECTOR PINOUT Pin # Signal Color Device Pin # 1 GND/Chassis Black/Grey 2 +15 Orange 3 3 CAN1_H (In5) Yellow 10 4 CAN1_L (In4) Green 9 5 Out0_LS Red/Black 13 6 RS232_Out Violet 17 7 RS232_In White 18 8 In0 Brown 5 9 CAN2_H (In7) Yellow/Red 12 10 CAN2_L (In6) Green/Red 11 11 In1 Light Blue 6 12 +30 Red 1 Pin # Signal Color 2-4 Device Pin # 1 In2 Pink 7 2 In3 Blue 8 3 Out1_HS White/Red 14 4 Out2_LS White/Black
BATTERY PACK WARNINGS DANGER - Opening the device by Unauthorized Personal VOIDS the Warranty! Never attempt to open the casing of the detachable batteries! NiMH batteries can be dangerous if mishandled! TROUBLESHOOTING Connectivity is the most common customer technical issue. Troubleshooting involves a series of tests to isolate the issue to the main points of failure (outlined below) from which the root cause can be identified, followed by the resolution.
TECHNICAL SUPPORT LINK TO USER GUIDE If the troubleshooting hints and tips in this Installation Manual fail to remedy the problem, please contact Tierra Support: support-tierra@tierratelematics.com Once the device is installed and running, you can access the User Guide at the following link: http://www.tierratelematics.com/download/CM1XInstallationManual.pdf When emailing, please provide the following information for better, faster service: 1. The device version. 2.
CERTIFICATIONS CERTIFICATIONS ANATEL Este equipamento não tem direito à proteção contra lnterferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. FCC 1. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2. This device model CM100/CM110 contains FCC ID: 2A6VC-AM35 and: FCC ID: XMR201606EC21A (Modem version EC21A) 3.This device complies with part 15 of the FCC Rules.
Part Number TRR-MAN-2F01 Rev A © Copyright Tierra S.p.A. June, 2022 All contents in this manual are copyrighted by Tierra S.p.A. All rights reserved. The information contained herein may not be used, accessed, copied, stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express written consent from Tierra S.p.A.
TIERRA S.p.A. Corso Ferrucci, 112 - 10138 Torino - Italy www.tierratelematics.
