User Manual MODEL: HPI212S
Contents Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting The Best From Your HPI212S . . . . . . . . . . . . . . 4 Flying Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 HPI212S Specifications. . . . . . . . . . . . . . . . . . . . . . . . .
HPI212S User Manual Safety Precautions • Be sure to read the instructions in this section carefully before use. • Make sure you observe the instructions in this manual as the conventions of safety symbols and messages are very important. • We also recommend you keep this instruction manual handy for future reference. Safety Symbol and Message Conventions Safety symbols described below are used in this manual to prevent bodily injury and property damage which could result from mishandling.
HPI212S User Manual WARNING When Installing the Unit When the Unit is in Use • Flying and\or installation of this speaker cabinet must be carried out by suitably qualified personnel following the locally authorised and approved safety standards. • Do not expose the unit to rain or an environment where it may be exposed to water or other liquids, as doing so may result in damage to the bass driver or corrosion of the steel protective grill.
HPI212S User Manual General Description The HPI212S is designed for the permanent installation and live sound touring market. It is suited to mid to high sound pressure level bass and sub bass high fidelity reproduction as a stand-alone unit or in combination with the 18” HPI18LP sub bass as a multi-way sub bass system.
HPI212S User Manual Getting The Best From Your HPI212S Amplification Connections The performance of any loudspeaker depends on the amplifier delivering an adequate supply of clean power. Please ensure a suitable amplifier is selected for use in conjunction with the HPI212S and accompanying speaker system. Two NL-4 connectors are mounted in a recessed panel on the rear surface of the box. This allows the speaker box to be set flat against a wall without physical interference to the speaker connector.
HPI212S User Manual Avoid Amplifier Clipping Finding a Suitable Amplifier Bearing in mind the previously described principle of amplifier power being higher than speaker power, keep signal levels low enough so that neither the Clip or Limit Active indicators are blinking frequently or are on continuously. If they are, turn down the input signal level. The HPI212S is a 4 ohm enclosure. A low power amplifier that is clipping will quickly damage the loudspeaker.
HPI212S User Manual Flying Your System Overhead Installation and Rigging 6 Purchaser\Installer Responsibility It is the responsibility of the purchaser and end-user of Quest Engineering products to: “Rigging” is used in this manual as a general term referring to fixed mounting or hangin suspension as well as the hardware used for such mounting and suspension. It also applies to temporary and permanent installation. 1. Read the product instructions and labels and follow them.
HPI212S User Manual Maintenance of Rigging Suspension systems can degrade with time, exposure to atmospheric conditions and ware, they require regular inspection and routine maintenance to insure the speaker cluster and fittings are secure. The installation must be inspected for fatigue at least annually.
HPI212S User Manual HPI212S Specifications Typical Frequency Reponse 110 100 90 80 70 60 8 50 20 50 100 200 500 1k 2k 5k HPI 1212S - Frequency Response - 2.83V/1m (processed) HPI 1212S - Frequency Response - 2.83V/1m Technical Specifications User Manual Power Handling 1000 W rms Frequency Response 45-250 Hz Sensitivity 93.
HPI212S User Manual HPI212S Reference Diagram 3 4 6 5 7 9 8 2 2bis 9 1 No. Description Spare Part 1 Complete Grille (inc. foam) HGHPI212S 2 12” Woofer (x2) T12007 2bis Recone Kit for 12” Woofer RT12007 3 Top Hat HTHHPI 4 Connection Plate (inc.
Register Your Product Thank you for choosing Quest. Please take the time to complete your product registration card which is included with the packaging. Registering your Quest Engineering product will: • CONFIRM YOUR WARRANTY • REGISTER YOUR PRODUCT • PROTECT YOUR NEW PRODUCT REGISTER ONLINE: www.questaudio.net/registration www.questaudio.