Tile Replacement Mount For use with Flat, S, & W shaped tiles Installation Instructions
Instructions: QMTR - Tile Replacement Mount Installation Tools Required: stud finder, tape measure, utility knife, drill with 1/8" bit, impact gun with T-30 Torx bit, channel lock pliers, caulking gun, appropriate sealant compatible with EPDM rubber and roofing materials, roofing bar, hand broom, stapler, 18" wide piece of underlayment or materials for 3-course method. NOTE: Installation method is the same for all tile replacement flashing profiles.
Waterproofing on Tile: Three-Course Method Installation Tools Required: gloves, hammer, brush, roofing cement, trowel, 4 inch wide roof repair fabric. Install the base mount. Clean away dust and debris. (See instructions on pg 1) Gather materials needed. Apply a bead of sealant in the shape of an upside down U on the back side of the base mount around the lag holes.
ITEM NO. 1 2 3 4 4 DESCRIPTION QTY. FLASHING, .040" X 12" X 7.5", SHEET, 5052H32, MILL TILE REPLACEMENT BASE, 8.125", 6061-T6, MILL WASHER, SEALING, 5/16" ID X 3/4" OD, EPDM BONDED SS LAG SCREW, GRK RSS WASHER HEAD, 5/16" X 4", T-30, STEEL, CLIMATEK COATED 1 1 2 2 3 1 TITLE: 2 QMTR-BM: TILE REPLACEMENT, BASE MOUNT UNLESS OTHERWISE SPECIFIED: PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF QUICK MOUNT PV.
BI 7.2.3-40 4 May-2016, Rev 1 5 4 PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF QUICK MOUNT PV. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF QUICK MOUNT PV IS PROHIBITED. BASE MOUNT SOLD SERARATELY (QMTR-BM) 4 5 6 7 8 1 2 3 3 2 DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL 1/8 TWO PLACE DECIMAL .18 THREE PLACE DECIMAL .125 UNLESS OTHERWISE SPECIFIED: DFM 1 5/12/2016 WEIGHT: 2.
BI 7.2.3-40 5 May-2016, Rev 1 5 4 1 2 3 3 2 DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL 1/8 TWO PLACE DECIMAL .18 THREE PLACE DECIMAL .125 UNLESS OTHERWISE SPECIFIED: DFM 1 5/12/2016 WEIGHT: 2.
BI 7.2.3-40 6 May-2016, Rev 1 1 2 3 5 4 3 THIS EDGE TOWARDS ROOF RIDGE 1 CAP SCREW, HEX HEAD, 5/16"-18 X 1" UNC2A, 18-8 SS 8 2 DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL 1/8 TWO PLACE DECIMAL .18 THREE PLACE DECIMAL .125 UNLESS OTHERWISE SPECIFIED: DFM 1 5/12/2016 WEIGHT: 2.80 DATE: DRAWN BY: SCALE: 1:5 A SIZE SHEET 1 OF 1 1 REV QMTR-S3.25: TILE REPLACEMENT, S-TILE, 3-1/4" POST 1 WASHER, SPLIT-LOCK, 5/16" ID, 18-8 SS 7 TITLE: 1 1 1 1 1 1 QTY.
925-478-8269 | www.quickmountpv.com | tech@quickmountpv.com 2700 Mitchell Dr. | Walnut Creek, CA 94598 BI 7.2.3-40 May-2016, Rev 1 ©2016 by Quick Mount PV. All rights reserved.
