SubCompact Board GENE-QM67 GENE-QM67 Intel® 2nd Generation CoreTM i5/Celeron® Processor 10/100/1000Base-TX Ethernet 8 USB2.0, 4 COM, 8-bit Digital I/O 2 SATA 6.0Gb/s (Optional RAID) CFast 1 Mini Card, LPC GENE-QM67 Manual Rev.A 1st Ed.
SubCompact Board GENE-QM67 Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
SubCompact Board GENE-QM67 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CFast™ is a trademark of the Compact Flash Association. Intel®, Core, and Celeron® are trademarks of Intel® Corporation. Microsoft Windows® is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
SubCompact Board GENE-QM67 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1 GENE-QM67 1 Cooler 1 DVD-ROM for Manual (in PDF Format) and Drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
SubCompact Board GENE-QM67 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................. 2-2 2.2 Location of Connectors and Jumpers ...................... 2-3 2.
SubCompact Board GENE-QM67 2.15 Touch Screen 4/5/8-wire Selection (JP10) ........... 2-11 2.16 Clear CMOS Selection (JP11) .............................. 2-11 2.17 AT/ATX Power Supply Mode Selection (JP12)..... 2-12 2.18 LVDS Port 1 Inverter/Backlight Connector (CN1) . 2-12 2.19 External +12V Input Connector (CN2) .................. 2-12 2.20 USB2.0 Port 7 and 8 (CN3)................................... 2-12 2.21 USB2.0 Port 5 and 6 (CN4)................................... 2-13 2.22 USB2.
SubCompact Board GENE-QM67 2.40 Intel LAN (RJ-45) Port (CN24) .............................. 2-22 2.41 USB Port 1 and 2 (CN25)...................................... 2-22 2.42 VGA/ DVI Ports (depends on hardware configuration) (CN26) ........................................................................... 2-23 2.43 COM Port 1 (D-SUB 9) (CN27) ............................. 2-24 2.44 CFast™ Slot (CN28) ............................................. 2-24 2.45 DDR3 SODIMM Slot (CN29).........................
SubCompact Board GENE-QM67 B.4 DMA Channel Assignments.……………………… .B-7 Appendix C Mating Connector C.1 List of Mating Connectors and Cables.................. C-2 Appendix D RAID & AHCI Settings D.1 Setting RAID ......................................................... D-2 D.2 Setting AHCI .......................................................
SubCompact Board GENE-QM67 Chapter 1 General Information Chapter 1 General Information 1- 1
SubCompact Board GENE-QM67 1.1 Introduction The GENE-QM67 supports Intel® 2nd Generation Intel® Core™ i5 Mobile/Celeron® processor which when paired with the Intel® QM67 chipset offers a high performance computing platform with low power consumption. This new product supports 204-pin DDR3 SODIMM at speeds of 1066/1333 MHz, up to 8 GB. One CFast™ and two SATA 6.0Gb/s (Optional RAID) interfaces provide ample storages. With dual Gigabit Ethernet, four COM ports, and eight USB2.
SubCompact Board GENE-QM67 1.2 Features Intel® 2nd Generation Core™ i5 Mobile/Celeron® (32nm) Processor Intel® QM67 204-pin DDR3 1066/1333 MHz SODIMM x 1, Up to 8 GB Gigabit Ethernet x 2 CRT, 18/24-bit Dual-Channel LVDS LCD x 2, DVI x 1 2CH HD Audio SATA 6.0Gb/s x 2 (Optional RAID), CFast x 1 USB2.
SubCompact Board GENE-QM67 1.3 Specifications System From Factor 3.
SubCompact Board GENE-QM67 Display: Supports CRT/LCD, DVI/LCD simultaneous / dual view displays Intel® QM67 integrated Chipset Memory Shared system memory up to 512MB Resolution Up to 2048x1536 for CRT Up to 1920 x 1200 for LCD, DVI DVI DVI x 1 I/O: ITE IT8728F + Fintek F81216D SATA 6.0Gb/s x 2 , CFast™ x 1 Storage Serial Port RS-232 x 3 RS-232/422/485 (auto flow) x 1 USB USB2.
SubCompact Board GENE-QM67 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2 - 1
SubCompact Board GENE-QM67 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
SubCompact Board GENE-QM67 2.
SubCompact Board Solder Side Chapter 2 Quick Installation Guide 2 - 4 GENE-QM67
SubCompact Board GENE-QM67 2.
SubCompact Board Solder Side Chapter 2 Quick Installation Guide 2 - 6 GENE-QM67
SubCompact Board GENE-QM67 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
SubCompact Board CN8 Audio I/O Port CN9 LVDS Port 1 CN10 LVDS Port 2 CN11 COM Port 2 CN12 LPT / Digital IO Port CN13 COM Port 3 GENE-QM67 CN15 COM Port 4 CN16 UIM Card Module CN17 PS/2 Keyboard/Mouse Combo Port CN18 +5VSB Output with SMBus CN19 Touch Screen Connector CN20 CPU FAN CN22 +5V Output for SATA HDD CN23 Realtek LAN (RJ-45) Port CN24 Intel LAN (RJ-45) Port CN25 USB Ports 1 and 2 CN26 VGA / DVI Ports (depend on hardware configuration) CN27 COM Port 1 (D-SUB 9) C
SubCompact Board GENE-QM67 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
SubCompact Board GENE-QM67 2.7 LVDS Port 2 Operating VDD Selection (JP2) JP2 Function 1-2 +5V 2-3 +3.3V (Default) 2.8 LVDS Port 1 Backlight Inverter VCC Selection (JP3) JP3 Function 1-2 +12V 2-3 +5V (Default) 2.9 LVDS Port 2 Backlight Inverter VCC Selection (JP4) JP4 Function 1-2 +12V 2-3 +5V (Default) 2.10 LVDS Port 2 Operating VDD Selection (JP5) JP5 Function 1-2 +5V 2-3 +3.3V (Default) 2.
SubCompact Board GENE-QM67 2.13 COM2 Pin8 Function Selection (JP8) JP8 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V 2.14 Front Panel Connector (JP9) 1 3 5 7 9 2 4 6 8 10 Pin Signal Pin Signal 1 PWRBTN(-) 2 PWRBTN(+) 3 HDLED(-) 4 HDLED(+) 5 SPEAKER(-) 6 SPEAKER(+) 7 PWRLED(-) 8 PWRLED(+) 9 RESET(-) 10 RESET(+) 2.15 Touch Screen 4/5/8-wire Selection (JP10) JP10 Function 1-2 4/8-wire Mode (Default) 2-3 5-wire Mode 2.
SubCompact Board GENE-QM67 2.17 AT/ATX Power Supply Mode Selection (JP12) JP12 Function 1-2 AT Mode (Default) 2-3 ATX Mode 2.18 LVDS Port 1 Inverter/Backlight Connector (CN1) Pin Signal 1 VDD 2 BKL_CTL 3 GND 4 GND 5 BKL_EN Note: LVDS1 VDD can be set to +5V or +12V by JP3. LVDS1 BKL_CTL can be set by JP6. 2.19 External +12V Input Connector (CN2) Pin Signal 1 +12V 2 GND 2.20 USB2.
SubCompact Board GENE-QM67 2.21 USB2.0 Port 5 and 6 (CN4) Pin Signal Pin Signal 1 +5V 2 GND 3 D- 4 GND 5 D+ 6 D+ 7 GND 8 D- 9 GND 10 +5V 2.22 USB2.0 Port 3 and 4 (CN5) Pin Signal Pin Signal 1 +5V 2 GND 3 D- 4 GND 5 D+ 6 D+ 7 GND 8 D- 9 GND 10 +5V 2.23 External +5VSB Input (CN6) Pin Signal 1 PSON# 2 GND 3 +5VSBY 2.
SubCompact Board GENE-QM67 UNote: LVDS2 VDD can be set to +5V or +12V by JP4. LVDS2 BKL_CTL can be set by JP7. 2.25 Audio I/O Port (CN8) Pin Signal 1 Microphone Left Channel 2 Microphone Left Channel 3 GND 4 Line-In Left Channel 5 Line-In Right Channel 6 GND 7 Line-Out Left Channel 8 GND 9 Line-Out Right Channel 10 +5V 2.
SubCompact Board GENE-QM67 23 DATA_B2- 24 DATA_B2+ 25 DATA_B3- 26 DATA_B3+ 27 VCC 28 GND 29 CLK_B30 Note: LVDS1 VCC can be set by JP5. CLK_B+ 2.
SubCompact Board GENE-QM67 3 RX RX+ N.C 4 RTS N.C N.C 5 TX TX+ A (Data+) 6 CTS N.C N.C 7 DTR RX- N.C 8 RI +5V/+12V +5V/+12V 9 GND GND GND Note: COM2 RS-232/422/485 can be set by BIOS setting. Default is RS-232. Pin 8 function can be set by JP8. 2.29 LPT/ Digital I/O Port (CN12) This connector offers 4-pair of digital I/O functions and address is A06h and A07h.
SubCompact Board GENE-QM67 Port 3 @A06h Pin 3 GPIO Set 7 / Bit 2 U18 Pin110(GPIO 72) Port 2 @A06h Pin 2 GPIO Set 7 / Bit 1 U18 Pin109(GPIO 71) Port 1 @A06h Pin 1 GPIO Set 7 / Bit 0 U18 Pin108(GPIO 70) LPT Mode Pin Signal Pin Signal 1 STROBE# 2 AFD# 3 D0 4 ERR# 5 D1 6 PRINT# 7 D2 8 SLIN# 9 D3 10 GND 11 D4 12 GND 13 D5 14 GND 15 D6 16 GND 17 D7 18 GND 19 ACK# 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SLCT 26 N.
SubCompact Board GENE-QM67 15 N.C 16 GND 17 N.C 18 GND 19 D7 20 GND 21 D6 22 GND 23 D5 24 GND 25 D4 26 N.C Note: LPT / Digital IO can be set by BIOS setting. Default is LPT Function. 2.30 COM Port 3 (CN13) Pin Signal 1 DCD 2 DSR 3 RX 4 RTS 5 TX 6 CTS 7 DTR 8 RI 9 GND 2.31 LPC Port (CN14) Pin Signal 1 AD0 2 AD1 3 AD2 4 AD3 5 +3.
SubCompact Board 9 33MCLK 10 DRQ0# 11 DRQ1# 12 SERIRQ GENE-QM67 2.32 COM Port 4 (CN15) Pin Signal 1 DCD 2 DSR 3 RX 4 RTS 5 TX 6 CTS 7 DTR 8 RI 9 GND 2.33 UIM Card Module (CN16) Pin Signal 1 PWR 2 RST 3 CLK 4 GND 5 VPP 6 DAT 2.
SubCompact Board GENE-QM67 3 GND 4 +5V 5 MS_DAT 6 MS_CLK 2.35 +5VSB Output with SMBus (CN18) Pin Signal 1 SMB_DAT 2 GND 3 SMB_CLK 4 GND 5 PSON# 6 +5VSB 2.
SubCompact Board 5 RIGHT 6 N.C 7 N.C 8 N.C 9 N.C GENE-QM67 5-wire Pin Signal 1 GND 2 UL(Y-) 3 UR(Y+) 4 LL(X-) 5 LR(X+) 6 SENSE 7 N.C 8 N.C 9 N.C 2.37 CPU FAN (CN20) Pin Signal 1 GND 2 VDD 3 TACH 2.
SubCompact Board 2.39 Realtek LAN (RJ-45) Port (CN23) Pin Signal 1 BI_DA+ 2 BI_DA- 3 BI_DB+ 4 BI_DC+ 5 BI_DC- 6 BI_DB- 7 BI_DD+ 8 BI_DD- 2.40 Intel LAN (RJ-45) Port (CN24) Pin Signal 1 BI_DA+ 2 BI_DA- 3 BI_DB+ 4 BI_DC+ 5 BI_DC- 6 BI_DB- 7 BI_DD+ 8 BI_DD- 2.
SubCompact Board GENE-QM67 2.42 VGA/ DVI Ports (depends on hardware configuration) (CN26) VGA Pin Signal Pin Signal 1 RED 2 GREEN 3 BLUE 4 N.C 5 GND 6 RED_RTN 7 GREEN_RTN 8 BLUE_RTN 9 +5V 10 GND 11 N.
SubCompact Board GENE-QM67 2.43 COM Port 1 (D-SUB 9) (CN27) Pin Signa l Pin Sign al 1 DCD 6 DSR 2 RX 7 RTS 3 TX 8 CTS 4 DTR 9 RI 5 GND 2.44 CFast™ Slot (CN28) Pin Signal S1 GND S2 A+ S3 A- S4 GND S5 B- S6 B+ S7 GND PC1 N.C PC2 GND PC3 N.C PC4 N.C PC5 N.C PC6 N.C PC7 GND PC8 N.C PC9 N.C PC10 N.C PC11 N.C PC12 N.
SubCompact Board PC13 +3.3V PC14 +3.3V PC15 GND PC16 GND PC17 N.C GENE-QM67 2.45 DDR3 SODIMM Slot (CN29) Standard specification 2.46 Mini Card Slot (CN30) P in Signa l Pin Signal 1 PCIE_WAKE# 2 +3.3VSB 3 N.C 4 GND 5 N.C 6 +1.5V 7 CLK_REQ# 8 UIM_PWR 9 GND 10 UIM_DATA 11 CLK- 12 UIM_CLK 13 CLK+ 14 UIM_RESET 15 GND 16 UIM_VPP 17 N.C 18 GND 19 N.C 20 Wireless DISABLE# 21 GND 22 Reset# 23 RX- 24 +3.3VSB 25 RX+ 26 GND 27 GND 28 +1.
SubCompact Board GENE-QM67 37 GND 38 USB_D+ 39 +3.3VSB 40 GND 41 +3.3VSB 42 N.C 43 GND 44 N.C 45 N.C 46 N.C 47 N.C 48 +1.5V 49 N.C 50 GND 51 N.C 52 +3.3VSB 2.47 SATA Port 1 (SATA1) Standard specification 2.
SubCompact Board GENE-QM67 2.49 Cooler & Fan Installations Please follow the installation steps to make sure the proper installation of the cooler and fan.
SubCompact Board Step 3 : Fasten the screw at the right-up side Step 4 : Fasten the screw at the right-down side Chapter 2 Quick Installation Guide 2 - 28 GENE-QM67
SubCompact Board GENE-QM67 Step 5 : Fasten the screw at the left-up side as the picture Step 6 : Connect the Fan Cable to the Fan Connector Chapter 2 Quick Installation Guide 2 - 29
SubCompact Board GENE-QM67 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2 - 30
SubCompact Board GENE-QM67 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
SubCompact Board 3.1 GENE-QM67 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
SubCompact Board 3.2 GENE-QM67 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
SubCompact Board GENE-QM67 switched to LVDS2 under the OS. 2. If the "Onboard LVDS2 (CH7511)" has been set "Enable," the status of the "Primary IGFx Boot Display" is concealed. The screen can be switched to LVDS2 under the OS.
SubCompact Board GENE-QM67 Chapter 4 Driver Installation .
SubCompact Board GENE-QM67 The GENE-QM67 comes with an AutoRun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
SubCompact Board 4.1 GENE-QM67 Installation: Insert the GENE-QM67 DVD-ROM into the DVD-ROM drive. And install the drivers from Step 1 to Step 9 in order. Step 1 – Install Chipset Driver Click on the STEP 1-CHIPSET folder and double click on the infinst_autol.exe file 1. Follow the instructions that the window shows 2. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the STEP2-VGA folder and select the OS folder your system is 2.
SubCompact Board GENE-QM67 Step 3 –Install LAN1 Driver (Intel® LAN Chip) 1. Click on the STEP3-LAN1 folder and select the OS folder your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 4 –Install LAN2 Driver (Realtek LAN Chip) 1. Click on the STEP4-LAN2 folder and select the OS folder your system is 2. Double click on the setup.exe file located in each OS folder 3.
SubCompact Board GENE-QM67 your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 7 – Install RAID & AHDI Driver Please refer to the Appendix D RAID & AHDI Settings Step 8 – Install TPM Driver 1. Click on the STEP8-TPM DRIVER folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3.
SubCompact Board GENE-QM67 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
SubCompact Board GENE-QM67 A.1 Programming GENE-QM67 utilizes ITE IT8728F chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8728F enters the normal mode with all logical devices disabled except KBC.
SubCompact Board GENE-QM67 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
SubCompact Board GENE-QM67 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
SubCompact Board GENE-QM67 WatchDog Timer Control Register (Index=71h, Default=00h) WatchDog Timer Configuration Register (Index=72h, Default=00h) WatchDog Timer Time-out Value Register (Index=73h, Default=00h) Appendix A Programming the Watchdog Timer A-5
SubCompact Board GENE-QM67 A.2 ITE8728F Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
SubCompact Board GENE-QM67 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Appendix A Programming the Watchdog Timer A-7
SubCompact Board GENE-QM67 RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL Appendix A Programming the Watchdog Timer A-8
SubCompact Board GENE-QM67 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
SubCompact Board GENE-QM67 push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
SubCompact Board GENE-QM67 Appendix B I/O Information Appendix B I/O Information B-1
SubCompact Board B.
SubCompact Board GENE-QM67 Appendix B I/O Information B-3
SubCompact Board B.
SubCompact Board GENE-QM67 B.
SubCompact Board Appendix B I/O Information B-6 GENE-QM67
SubCompact Board GENE-QM67 B.
SubCompact Board GENE-QM67 Appendix C Mating Connector Appendix C Mating Connector C - 1
SubCompact Board GENE-QM67 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Label Mating Connector Function Vendor Model No.
SubCompact Board GENE-QM67 CN13 COM Port 3 Connector Molex 51021-0900 Serial Port Cable 1701090150 CN14 LPC Port JST SHR-12V-SB AAEON LPC Cable 1703120130 CN15 COM Port 4 Connector Molex 51021-0900 Serial Port Cable 1701090150 CN16 UIM Connector Molex 51021-0600 N/A N/A CN17 P/S2 KB/MS Connector JST PHDR-06V S P/S2 KB/MS Cable 1700060152 CN18 External AUX Power and PS_ON# JST PHR-6 N/A N/A CN19 Touch Screen Connector JST SHR-9V-SB N/A N/A CN20 CPU Fan Connector
SubCompact Board GENE-QM67 Appendix D RAID & AHCI Settings Appendix D RAID & AHCI Settings D-1
SubCompact Board GENE-QM67 D.
SubCompact Board GENE-QM67 Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Mode -> RAID Mode Step 4: The setting procedures “In BIOS Setup Menu” B: Advanced -> Launch Storage OpROM -> Enabled Appendix D RAID & AHCI Settings D-3
SubCompact Board GENE-QM67 Step 5: The setting procedures “In BIOS Setup Menu” C: Boot -> Boot Option #1 -> DVD-ROM Type Step 6: The setting procedures “In BIOS Setup Menu” D: Save & Exit -> Save Changes and Exit Appendix D RAID & AHCI Settings D-4
SubCompact Board GENE-QM67 Step 7: Press Ctrl-I to enter MAIN MENU Step 8: Choose “1.
SubCompact Board Step 9: RAID Level -> RAID0(Stripe) Step 10: Choose “Create Volume” Appendix D RAID & AHCI Settings D-6 GENE-QM67
SubCompact Board GENE-QM67 Step 11: Choose “Y” Step 12: Choose “5.
SubCompact Board Step 13: Choose “Y” Step 14: Setup OS Appendix D RAID & AHCI Settings D-8 GENE-QM67
SubCompact Board GENE-QM67 Step 15: Press “F6” Step 16: Choose “S” Appendix D RAID & AHCI Settings D-9
SubCompact Board GENE-QM67 Step 17: Choose “Intel(R) Mobile Express Chipset SATA RAID Controller” Step 18: It will show the model number you select and then press “ENTER” Appendix D RAID & AHCI Settings D-10
SubCompact Board GENE-QM67 Step 19: Setup is starting Windows Appendix D RAID & AHCI Settings D-11
SubCompact Board GENE-QM67 D.
SubCompact Board GENE-QM67 Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Configuration -> SATA Mode -> AHCI Mode Step 4: The setting procedures “In BIOS Setup Menu” B: Boot -> Boot Option #1 -> DVD-ROM Type Appendix D RAID & AHCI Settings D-13
SubCompact Board GENE-QM67 Step 5: The setting procedures “In BIOS Setup Menu” C: Save & Exit -> Save Changes and Exit Step 6: Setup OS Appendix D RAID & AHCI Settings D-14
SubCompact Board GENE-QM67 Step 7: Press “F6” Step 8: Choose “S” Appendix D RAID & AHCI Settings D-15
SubCompact Board GENE-QM67 Step 9: Choose “Intel(R) Mobile Express Chipset SATA AHCI Controller” Step 10: It will show the model number you select and then press “ENTER” Appendix D RAID & AHCI Settings D-16
SubCompact Board GENE-QM67 Step 11: Setup is loading files Appendix D RAID & AHCI Settings D-17
