Instructions / Assembly

ManualsBrandsQUICKJACK ManualsOtherMotorcycle Lift Kit

1645 Lemonwood Dr.

Santa Paula, CA 93060 USA

Toll Free: (888) 262-3880

Tel: (805) 421-5114

quickjack.com

Motorcycle and ATV/Motorcycle Lift Adapter Kits

Installation and Operation Manual

Manual P/N 5900054 — Manual Revision B — April 2019

Motorcycle Lift Adapter Kit shown. QuickJack, Ranger RML-1100 Motorcycle Jack, technician, and motorcycle

not

included.

QuickJack is designed and engineered by BendPak Inc. in Southern California, USA. Made in China.

⚠ DANGER

IMPORTANT SAFETY INSTRUCTIONS, SAVE THESE INSTRUCTIONS!

Read the

entire

contents of this manual

before

installing, operating,

servicing, or maintaining this lift. Failure to follow the instructions and

safety precautions in this manual can result in serious injury or death.

Make sure all other operators also read this manual. Keep the manual

near the product for future reference. By proceeding with installation and

operation, you agree you fully understand the contents of this manual.

Summary of content (12 pages)

PAGE 1
645 Lemonwood Dr. Santa Paula, CA 93060 USA Toll Free: (888) 262-3880 Tel: (805) 421-5114 quickjack.com Motorcycle and ATV/Motorcycle Lift Adapter Kits Installation and Operation Manual Manual P/N 5900054 — Manual Revision B — April 2019 Motorcycle Lift Adapter Kit shown. QuickJack, Ranger RML-1100 Motorcycle Jack, technician, and motorcycle not included. QuickJack is designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
PAGE 2
Manual. QuickJack Motorcycle and ATV/Motorcycle Adapter Kits, Installation and Operation Manual, Manual P/N 5900054, Manual Revision B, Released April 2019. Copyright. Copyright © 2019 by BendPak Inc. All rights reserved. You may make copies of this document if you agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain any rights to this content, and you will not use the copies for commercial purposes. Trademarks.
PAGE 3
Table of Contents Introduction 3 System Components 7 Shipping Information 4 Setup 9 Safety Considerations 4 Operation 10 Specifications 6 Maintenance 11 Introduction This manual describes the: • Motorcycle Lift Adapter Kit. Holds your motorcycle in place while you service or repair it. Requires a working QuickJack. Not compatible with the BL-6000XLT model. • ATV/Motorcycle Lift Adapter Kit. Holds your ATV or motorcycle in place while you service or repair it.
PAGE 4
Shipping Information Your equipment was carefully checked before shipping. Nevertheless, you should thoroughly inspect the shipment before you sign to acknowledge that you received it. When you sign the bill of lading, it tells the carrier that the items on the invoice were received in good condition. Do not sign the bill of lading until after you have inspected the shipment.
PAGE 5
• QuickJack recommends making a thorough inspection of the product at least once a year. Replace any damaged or severely worn parts, decals, or warning labels. Symbols Following are the symbols used in this manual: ⚠ DANGER Calls attention to an immediate hazard that will result in injury or death. ⚠ WARNING Calls attention to a hazard or unsafe practice that could result in injury or death.
PAGE 6
Specifications Model Motorcycle Adapter Kit ATV/Motorcycle Adapter Kit Platform width 28.5" / 725 mm 47.25" / 1200 mm Platform length 88" / 2,236 mm 88" / 2,236 mm Platform height 3" / 76 mm 3" / 76 mm Ramp length 6.25" / 159 mm 6.25" / 159 mm Weight of Platform plus clamp assembly 104 lbs (47 kg) 124 lbs (56.25 kg) Maximum supported weight 1,000 lbs (453 kg) 1,000 lbs (453 kg) ⚠ WARNING Do not put a vehicle weighing more than 1,000 lbs (453 kg) on the Platform.
PAGE 7
System Components System components include the Platform (with Clamp Assembly) and your QuickJack. The Platform Motorcycle and ATV/Motorcycle Lift Adapter Kits 7 P/N 5900054 —Rev.
PAGE 8
The QuickJack The Lift Adapter Kit requires a QuickJack; the platform sits on top of your QuickJack frames. Tip This manual assumes your QuickJack is already set up and working. If it is not, you need to set it up so you can use your Lift Adapter Kit. Refer to the QuickJack Installation and Operation manual for more information about setting up and using your QuickJack. The latest version of the QuickJack Setup and Operation Manual can always be found on the QuickJack website: quickjack.com/downloads.html.
PAGE 9
Setup ⚠ WARNING Do not use the Lift Adapter Kit where the slope of the floor is greater than 3 degrees; this makes it much more likely that the load on the platform will become off balance and fall, potentially damaging the platform, the QuickJack, or any people in the vicinity. Make sure to wear appropriate work clothing while setting up the Lift Adapter Kit, including gloves and steel-toed work boots. To set up your Lift Adapter Kit: 1. Unpack. The platform and the clamp assembly come in separate boxes.
PAGE 10
You can put the Lift Adapter Kit onto the QuickJack frames when the QuickJack frames are on the ground or in the first locked position. If you are having trouble putting on the platform with the QuickJack frames on the ground, try raising the frames to the first locked position. If you do put the platform on with the QuickJack frames in the first locked position, make sure to lower them before trying to put a vehicle on the platform. ⚠ WARNING The platform must fit securely on the QuickJack frames.
PAGE 11
Maintenance ⚠ WARNING Before performing any maintenance on your Lift Adapter Kit, make sure the QuickJack’s power unit is disconnected from the power source and cannot be reconnected until the maintenance is complete. To maintain your Lift Adapter Kit: • Cleanliness. Always keep your Lift Adapter Kit clean. Make sure to wipe it down after each use; remove any grease, dirt, or other debris. You can use cleaning materials on the platform, but keep them away from the QuickJack frames. • Storage.