Instructions / Assembly

ManualsBrandsQUICKJACK ManualsOtherBL-7000SLX 7,000 lbs. Capacity Portable Car Lift Bundle Package with 12pc adapter set and wall hangers

Table Of Contents

QuickJack Manual
Table of Contents
Introduction
Shipping
Safety
- Important Safety Instructions
- QuickJack Safety Information
- Symbols
- Liability Information
Components
Accessories
- SUV and Light Truck Adapter Kit
- SLX Frame Extension Kit
- Motorcycle Lift Adapter Kit
- Ranger RML-1100 Motorcycle Jack
- JackPak
Specifications
Frequently Asked Questions
Setup Checklist
Setup
- Setup Safety Rules
- Tools
- Selecting a Site
- Unpacking
- Clearances
- QuickJack Assembly Kit
- Air and Hydraulic Cylinders
- Installing the Hydraulic Elbow Fittings
- Preparing the Short Hydraulic Hoses
- About Quick-Connect Fittings
- Routing the Short Hydraulic Hoses
- Preparing and Connecting the Long Hydraulic Hoses
- Pressurizing the Air Cylinders
- Find a Location for the Power Unit
- Installing the Hydraulic Fittings on the Power Unit
- Connect the Power Unit to a Power Source
  - Power Sources for VAC Power Units
    - 110 VAC Power Unit
    - 220/240 VAC Power Unit
  - Power Sources for 12 VDC Power Units
    - 12 VDC Power Unit
- Filling the Hydraulic Fluid Reservoir on the Power Unit
- Check the Breather Valve
- Connect the Hydraulic Hoses
- Bleeding the Hydraulic Cylinders
- Final Checklist Before Operation
- Test the QuickJack
- Leave the Manual with the Owner/Operator
Operation
- Safety
- About Lift Blocks
- Special QuickJack Warnings
- Positioning the Lift Blocks and Frames
- Raising the QuickJack Frames
- Lowering the Frames from the First Locking Position
- Lowering the Frames from the Top Locking Position
- Using the 12 VDC Power Unit
- Additional Operating Information
- Hydraulic System Warnings
Maintenance
- Lubrication Points
- About Outdoor Operation
Troubleshooting
- Frames at Full Height with No Load
- Vehicle with No Tires Fully Lowered
- Priming the Pump
Wiring Diagrams
- 12 VDC Wiring Diagram
- 208-230 VAC Wiring Diagram
Labels
Parts Sheets
Automotive Lift Institute (ALI) Store
Maintenance Log
CE Documentation

QuickJack™ Portable Car Jack 14 P/N 5900959 — Rev. J3 — Oct. 2019

Setup Checklist

Following are the steps needed to install a QuickJack. Perform them in the order shown.

☐ 1. Review the setup Safety Rules.

☐ 2. Make sure you have the necessary Tools.

☐ 3. Select the setup Site.

☐ 4. Unpack the Components that came with the QuickJack.

☐ 5. Make sure there is adequate Clearance on all sides and above.

☐ 6. Locate the QuickJack Assembly Kit.

☐ 7. Locate and examine the Air and Hydraulic Cylinders.

☐ 8. Install the Hydraulic Elbow Fittings.

☐ 9. Prepare the Short Hydraulic Hoses.

☐ 10. Understand Quick-Connect Fittings

☐ 11. Route the Short Hydraulic Hoses.

☐ 12. Prepare and connect the Long Hydraulic Hoses.

☐ 13. Pressurize the Air Cylinders.

☐ 14. Find a location for the Power Unit.

☐ 15. Install fittings on the Power Unit.

☐ 16. Connect the Power Unit to a Power Source.

☐ 17. Fill the Hydraulic Fluid Reservoir.

☐ 18. Check the Breather Valve.

☐ 19. Connect the Hydraulic Hoses.

☐ 20. Bleed the Hydraulic Cylinders.

☐ 21. Review the Final Checklist.

☐ 22. Test the QuickJack.

☐ 23. Leave the Manual for the owner/operator.