Instructions / Assembly

ManualsBrandsQUICKJACK ManualsOtherBL-7000SLX 7,000 lbs. Capacity Portable Car Lift Bundle Package with 12pc adapter set and wall hangers

Table Of Contents

QuickJack Manual
Table of Contents
Introduction
Shipping
Safety
- Important Safety Instructions
- QuickJack Safety Information
- Symbols
- Liability Information
Components
Accessories
- SUV and Light Truck Adapter Kit
- SLX Frame Extension Kit
- Motorcycle Lift Adapter Kit
- Ranger RML-1100 Motorcycle Jack
- JackPak
Specifications
Frequently Asked Questions
Setup Checklist
Setup
- Setup Safety Rules
- Tools
- Selecting a Site
- Unpacking
- Clearances
- QuickJack Assembly Kit
- Air and Hydraulic Cylinders
- Installing the Hydraulic Elbow Fittings
- Preparing the Short Hydraulic Hoses
- About Quick-Connect Fittings
- Routing the Short Hydraulic Hoses
- Preparing and Connecting the Long Hydraulic Hoses
- Pressurizing the Air Cylinders
- Find a Location for the Power Unit
- Installing the Hydraulic Fittings on the Power Unit
- Connect the Power Unit to a Power Source
  - Power Sources for VAC Power Units
    - 110 VAC Power Unit
    - 220/240 VAC Power Unit
  - Power Sources for 12 VDC Power Units
    - 12 VDC Power Unit
- Filling the Hydraulic Fluid Reservoir on the Power Unit
- Check the Breather Valve
- Connect the Hydraulic Hoses
- Bleeding the Hydraulic Cylinders
- Final Checklist Before Operation
- Test the QuickJack
- Leave the Manual with the Owner/Operator
Operation
- Safety
- About Lift Blocks
- Special QuickJack Warnings
- Positioning the Lift Blocks and Frames
- Raising the QuickJack Frames
- Lowering the Frames from the First Locking Position
- Lowering the Frames from the Top Locking Position
- Using the 12 VDC Power Unit
- Additional Operating Information
- Hydraulic System Warnings
Maintenance
- Lubrication Points
- About Outdoor Operation
Troubleshooting
- Frames at Full Height with No Load
- Vehicle with No Tires Fully Lowered
- Priming the Pump
Wiring Diagrams
- 12 VDC Wiring Diagram
- 208-230 VAC Wiring Diagram
Labels
Parts Sheets
Automotive Lift Institute (ALI) Store
Maintenance Log
CE Documentation

QuickJack™ Portable Car Jack 19 P/N 5900959 — Rev. J3 — Oct. 2019

QuickJack Assembly Kit

Many of the items you will be using during initial setup come in the QuickJack Assembly Kit, which is a

clear plastic container included in your QuickJack packaging.

The QuickJack Assembly Kit includes:

• Four female Quick-Connect Fittings (for Long Hydraulic Hoses, both ends of each hose)

• Two male Quick-Connect Fittings (one for each Short Hydraulic Hose)

• Two Power Unit Quick-Connect Fittings (both connect to the Hydraulic Ports on the front of the

Power Unit, one above the other; put on the bottom one first)

• Two Hydraulic Elbow Fittings (one for each Hydraulic Cylinder)

• Thread Seal Tape

• Four plastic feet (for Power Units with carriers)

• Two

replacement

wheels

Air and Hydraulic Cylinders

Each QuickJack Frame has one Air Cylinder and one Hydraulic Cylinder.

The components of the Air and Hydraulic Cylinders are:

• Air Inflation Valve. Used to add air pressure to the Air Cylinder. Comes with the appropriate

valve (also called a Schrader® valve) installed.

• Hydraulic Cylinder Connector. Hydraulic Elbow Fitting attaches here. Use a 6 mm hex key to

remove the shipping plug before installing the Hydraulic Elbow Fitting.

• Bleeder Screw. Used to “bleed” the air from the Hydraulic System, if necessary. Refer to

Troubleshooting for more information.