Instructions / Assembly
Table Of Contents
- QuickJack Manual
 - Table of Contents
 - Introduction
 - Shipping
 - Safety
 - Components
 - Accessories
 - Specifications
 - Frequently Asked Questions
 - Setup Checklist
 - Setup
- Setup Safety Rules
 - Tools
 - Selecting a Site
 - Unpacking
 - Clearances
 - QuickJack Assembly Kit
 - Air and Hydraulic Cylinders
 - Installing the Hydraulic Elbow Fittings
 - Preparing the Short Hydraulic Hoses
 - About Quick-Connect Fittings
 - Routing the Short Hydraulic Hoses
 - Preparing and Connecting the Long Hydraulic Hoses
 - Pressurizing the Air Cylinders
 - Find a Location for the Power Unit
 - Installing the Hydraulic Fittings on the Power Unit
 - Connect the Power Unit to a Power Source
 - Filling the Hydraulic Fluid Reservoir on the Power Unit
 - Check the Breather Valve
 - Connect the Hydraulic Hoses
 - Bleeding the Hydraulic Cylinders
 - Final Checklist Before Operation
 - Test the QuickJack
 - Leave the Manual with the Owner/Operator
 
 - Operation
 - Maintenance
 - Troubleshooting
 - Wiring Diagrams
 - Labels
 - Parts Sheets
 - Automotive Lift Institute (ALI) Store
 - Maintenance Log
 - CE Documentation
 
QuickJack™ Portable Car Jack  49  P/N 5900959 — Rev. J3 — Oct. 2019 
About Outdoor Operation 
Your QuickJack is approved for indoor installation and use only. 
Outdoor installation is 
prohibited
. 
Your QuickJack is portable, however, so if you end up taking it outdoors, remember to protect it from 
the weather (for example, from falling dirt, rain, sleet, and snow). 
Here are some additional things to consider if you end up taking your QuickJack outside: 
•  Extreme environmental conditions must be avoided. The QuickJack warranty does not 
cover damage from rain, snow, sleet, excessive humidity, corrosive agents, hazardous and/or 
combustible fibers and flyings, or other contaminants. Keep your QuickJack protected from these 
environmental conditions at all times. 
•  The QuickJack lifetime may be reduced. Taking a QuickJack outside means it is subject to 
a harsher environment: a QuickJack ages more quickly the more it is outside. 
•  Maintenance and replacement parts costs may increase. The longer you keep your 
QuickJack outside, even when protected from the weather, the more often it will need 
maintenance: metal parts rust, plastic parts break down and dry out, hydraulic fluid gets dirty 
faster, and so on. Keeping your QuickJack outside for long periods is usually going to require extra 
maintenance and more frequent replacement parts. 
Here are some things customers have told us they did with QuickJacks they took outside: 
•  Move it back inside when done. It may seem obvious, but here it is: when you are done with 
your QuickJack outside, even if it was protected from the weather, bring it back inside and 
thoroughly clean it. 
•  Cover the Power Unit. 
This one is really important
. The Power Unit includes an electric 
motor. If that motor gets wet, people could get electrocuted, a fire could start, and almost certainly 
the motor will short circuit and stop functioning. 
These things are not covered by the 
QuickJack warranty
. This advice applies your QuickJack at all times; keep the Power Unit 
protected from all sources of moisture. 
•  Put up a carport canopy, party tent, or other structure. And then put the QuickJack 
under the structure. It blocks the sun and the rain, reducing the impact the outside environment 
has on the QuickJack. 
•  Use Ground Fault Circuit Interrupter (GFCI) protection. If available, use a GFCI circuit 
breaker in the service panel (breaker box) to protect the entire circuit. 
•  Increase the maintenance. If the maintenance instructions say to do something every day, 
check it twice a day; if they say to do something once a week, check it two times a week; and so 
on. This will help minimize the impact the outside environment has on your QuickJack. 
•  Increase the replacement parts. Parts on a QuickJack you take outside are not going to last 
as long as normal. Be prepared to start ordering replacement parts sooner. 










