Installation Guide

ManualsBrandsQuickStep ManualsLaminate Flooring SamplesLWCQS316

Quick Step Studio Laminate Flooring Installation Instructions

For more information, visit QuickStepatLowes.com or call 1-888-387-9882

2019_0202_QS_LOW_INST

10' (3 m)

)mm 031( "5 >

nigriv )mm 51.0( lim 6

polyethelene vapor barrier

ground

)mm 002( "8 >

Site Requirements

Laminate is a durable ﬂoor covering, not intended as structural

material. Laminate requires a clean, dry, secure subﬂoor that

meets building codes.

The following requirements are not intended to supersede federal,

state or local building codes, but as with many other interior ﬁnish

products, may require modifying existing structural components

for successful installation. Owner assumes responsibility for

compliance with all building codes.

Laminate ﬂoor is suitable for use in climate controlled (35-65% RH

and 60-85° F) indoor installations only and should not be installed

over any ﬂoor with a sump pump or in a room with a ﬂoor drain.

Laminate ﬂoor can be installed above, on or below grade.

A moisture test is strongly recommended to determine if high

moisture exists in the subﬂoor. When using a calcium chloride

moisture test for concrete subﬂoors (ASTM F1869), values must

be ≤ 5 lbs/1000ft²/24-hr or <80% RH with an in situ probe (ASTM

F2170). Moisture readings of wood subﬂoors must be ≤ 12%.

Acceptable job site conditions, including relative humidity and

subﬂoor moisture conditions, must be maintained throughout the

lifetime of the ﬂooring.

Laminate ﬂooring is installed as a ﬂoating ﬂoor and requires the

use of T-moldings in doorways 4 ft (1.22m) or less and in rooms

40 feet (12.2 m) or larger in length or width. Floor movement must

not be constrained by glue, nails, screws, hardware or other ﬁxed

obstructions.

This product must be installed in accordance with these

installation instructions.

Job Site

Tools Required for InstallationTools Required for Installation

Common Tools

Wood

Glue

Carbide

40T Blade

Other Tools and Supplies

(

)

PREMIUM

SYSTEM

COMPONENT

Finishing

Putty

PREMIUM

SYSTEM

COMPONENT

Finishing

Putty

SILICONE

CAULK

SILICONE

CAULK

SILICONE

CAULK

100% Silicone

Sealant

Felt furniture

pads

Moisture

Meter

Non Destructive Moisture

dlfwej dtra

djflsv

dlfwe vtra

alskdjf

vmwjc

Concrete

Encounter

Plus

100

150

200

250

Moisture

Meter

Laminate ﬂoor tapping

block and 5mm (3/16")

spacers

PE Foam

Backer Rod

Summary of content (14 pages)

PAGE 1
Quick Step Studio Laminate Flooring Installation Instructions Tools Required for Installation Other Tools and Supplies Spa cer 5m m s Finishing Putty LY DEVEL O AL PE I M AD 3 2 1 dlfwej dtra djflsv 4 5 6 0 50 ers 0 D FOR LA 100 150 Concrete Encounter Plus 200 250 IUM PREM IUM EM PREM SYST EM ENT SYST PON ENT COM PON COM TE FL O IN A O ac NG SPE C Sp 5m m M Carbide 40T Blade Wood Glue RI Common Tools S E IN THE U dlfwe vtra alskdjf vmwjc Moisture Meter A 1 FL OZ (33.
PAGE 2
Quick Step Studio Laminate Flooring Installation Instructions Site and Material Preparation A B Wallbase Door Frame Casing Cutting Line C D 1 inch (2,5 cm) E % 48 hours F 60° – 85° F 15° – 29° C 35% – 65% RH G H > 8" (200 mm) subfloor 6 mil (0.15 mm) virgin polyethelene vapor barrier A) Remove carpet and padding. Also remove any wood flooring installed on concrete. Do not remove products unless they are asbestos-free. B) Undercut door frame and wallbase.
PAGE 3
Quick Step Studio Laminate Flooring Installation Instructions Flooring Installation 1 2 3 4 Left Right 5 6 8 7 2 6 1 5 3 4 6 5 6 5 > 6 in > 15,24 cm 9 10 1 13 3 12 3 4 2 18 11 14 15 16 17 19 2019_0202_QS_LOW_INST
PAGE 4
Quick Step Studio Laminate Flooring Installation Instructions Flooring Installation 1. Inspect each plank. Floor should be installed blending planks from several cartons at the same time to ensure good color and shade mixture throughout the installation. 2. For the first row along straight walls, remove the tongue on all long side joints and on the short side of the 1st plank only. 3. For uneven walls, trace contour on tongue-side of plank and cut. 4. Assemble the first row tongue side toward wall.
PAGE 5
Quick Step Studio Laminate Flooring Installation Instructions A B C Care and Cleaning Place felt floor protectors under legs of moveable furniture. Chair casters should be rubber — not plastic or metal. Place walk-off mats at entrances. Dust mop as primary cleaning method. Occasionally damp mop with water only, using a well wrung out mop; DO NOT pour liquid directly on floor or use an excessively wet mop that will puddle or leave moisture standing on the floor.
PAGE 6
Quick Step Studio Laminate Flooring on Wall Install Instructions Although originally designed as a durable floor covering, many consumers have started using Quick-Step® Studio™ laminate flooring on walls to give their rooms more character and to create a feature or accent wall. Laminate can be utilized as a decorative covering over an existing clean, dry, secure and vertical wall that meets building codes. The wall substrate should be primed or painted drywall (gypsum board) only.
PAGE 7
Quick Step Studio Vertical Wainscot Style Wall Install Instructions 1. Measure the length of your laminate plank and the length of the wall area to determine the total square footage area. Order that amount of flooring plus an additional 10% for incorrect cuts. 2. Remove all base and trim from accent wall. Measure from the floor a distance equal to your laminate plank plus one inch then level and mark the wall with a chalk line. With an electronic stud finder locate and mark wall studs. (Figure 1) 3.
PAGE 8
Quick Step Studio Vertical Wainscot Style Wall Install Instructions 8. Apply silicone adhesive to the back side of the plank in an “S” pattern. If you’re using a laminate plank with an attached pad, apply the silicone directly to the pad on the back of the plank. (Figure 3) 9. Adhere the plank to the wall leaving a 3/16" gap (A) from the corners of the wall and a 1" gap (B) at bottom. Drive brad nails 1/2" from the top and bottom of each plank to secure to wall. Place nails where the trim will cover.
PAGE 9
Quick Step Studio Horizontal Accent Wall Install Instructions 1. Measure the length and width of the wall area to determine the total square footage area. Order that amount of flooring plus an additional 10% for incorrect cuts. 2. Remove baseboards from the accent wall and locate the wall studs using the stud finder tool. Mark vertical lines over all studs. Use painters tape to extend stud location to ceiling if needed. (Figure 1) 3. Turn off power while working around wall outlets and light switches.
PAGE 10
Quick Step Studio Horizontal Accent Wall Install Instructions 9. Drive a brad nail into each plank at each wall stud through the shallow area of the extended groove (see inset diagram). Take care that the brad nail heads are not raised, but also don’t force them all the way through the groove. This will allow easy connection of the next row of planks.
PAGE 11
Quick Step Studio Horizontal Accent Wall Install Instructions 13. Repeat this process for each plank working your way up to the last row. (Figure 8) 14. For the last row of the installation, use painters tape to mark the stud location for brad nailing. Cut all planks in the last row to the required width to complete the installation. Complete the installation as you have the earlier rows. (Figure 8A) 15. Use quarter round for inside corners and ceiling. Finish with wall base board of your choice.
PAGE 12
Quick Step Studio Laminate Flooring on Wall Install Instructions Care and Cleaning Dry wipe as primary cleaning method. Occasionally damp wipe with water only. NO wet washing. If needed, use 1 cup of vinegar per gallon of water OR 1/3 cup non-sudsing ammonia per gallon of water. DO NOT use detergents, abrasive cleaners, soaps, waxes or polishes. Wipe off spills immediately. DO NOT allow moisture to remain on the product surface for longer than 30 minutes.
PAGE 13
Quick Step Studio Limited Lifetime* Residential Warranty for Wall Installations Only Quick•Step provides the following limited lifetime* residential warranty to the original purchaser for as long as he or she owns the product in its original installation: (1) the laminate surface will not fade due to sun or electrical light; and (2) the laminate surface will not stain. These limited warranties are subject to the conditions described in the “Conditions” section below.
PAGE 14
Quick Step Studio Limited Lifetime* Residential Warranty for Wall Installations Only DISCLAIMERS: QUICK•STEP DISCLAIMS ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THIS PRODUCT. Quick•Step disclaims liability for incidental and consequential damages. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.